Merge git://www.denx.de/git/u-boot

52 files changed, 4028 insertions, 362 deletions

diff --git a/board/amcc/acadia/Makefile b/board/amcc/acadia/Makefile
index ddbcb8091f..c56b2733a9 100644
--- a/board/amcc/acadia/Makefile
+++ b/board/amcc/acadia/Makefile
@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= $(obj)lib$(BOARD).a
 
-COBJS	= $(BOARD).o cmd_acadia.o cpr.o memory.o
+COBJS	= $(BOARD).o cmd_acadia.o memory.o pll.o
 SOBJS	=
 
 SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
diff --git a/board/amcc/acadia/acadia.c b/board/amcc/acadia/acadia.c
index 46d63e6308..8b82ea40ed 100644
--- a/board/amcc/acadia/acadia.c
+++ b/board/amcc/acadia/acadia.c
@@ -31,13 +31,13 @@ static void acadia_gpio_init(void)
 	/*
 	 * GPIO0 setup (select GPIO or alternate function)
 	 */
-       	out32(GPIO0_OSRL, CFG_GPIO0_OSRL);
-       	out32(GPIO0_OSRH, CFG_GPIO0_OSRH);	/* output select */
-       	out32(GPIO0_ISR1L, CFG_GPIO0_ISR1L);
-       	out32(GPIO0_ISR1H, CFG_GPIO0_ISR1H);	/* input select */
-       	out32(GPIO0_TSRL, CFG_GPIO0_TSRL);
-       	out32(GPIO0_TSRH, CFG_GPIO0_TSRH);	/* three-state select */
-       	out32(GPIO0_TCR, CFG_GPIO0_TCR);  /* enable output driver for outputs */
+	out32(GPIO0_OSRL, CFG_GPIO0_OSRL);
+	out32(GPIO0_OSRH, CFG_GPIO0_OSRH);	/* output select */
+	out32(GPIO0_ISR1L, CFG_GPIO0_ISR1L);
+	out32(GPIO0_ISR1H, CFG_GPIO0_ISR1H);	/* input select */
+	out32(GPIO0_TSRL, CFG_GPIO0_TSRL);
+	out32(GPIO0_TSRH, CFG_GPIO0_TSRH);	/* three-state select */
+	out32(GPIO0_TCR, CFG_GPIO0_TCR);  /* enable output driver for outputs */
 
 	/*
 	 * Ultra (405EZ) was nice enough to add another GPIO controller
@@ -55,10 +55,12 @@ int board_early_init_f(void)
 {
 	unsigned int reg;
 
+#if !defined(CONFIG_NAND_U_BOOT)
 	/* don't reinit PLL when booting via I2C bootstrap option */
 	mfsdr(SDR_PINSTP, reg);
 	if (reg != 0xf0000000)
 		board_pll_init_f();
+#endif
 
 	acadia_gpio_init();
 
diff --git a/board/amcc/acadia/memory.c b/board/amcc/acadia/memory.c
index 25904d3b94..9346d2c52f 100644
--- a/board/amcc/acadia/memory.c
+++ b/board/amcc/acadia/memory.c
@@ -31,6 +31,8 @@
 #include <asm/io.h>
 #include <asm/gpio.h>
 
+extern void board_pll_init_f(void);
+
 /*
  * sdram_init - Dummy implementation for start.S, spd_sdram used on this board!
  */
@@ -67,6 +69,15 @@ static void cram_bcr_write(u32 wr_val)
 
 long int initdram(int board_type)
 {
+#if defined(CONFIG_NAND_SPL)
+	u32 reg;
+
+	/* don't reinit PLL when booting via I2C bootstrap option */
+	mfsdr(SDR_PINSTP, reg);
+	if (reg != 0xf0000000)
+		board_pll_init_f();
+#endif
+
 #if !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
 	int i;
 	u32 val;
diff --git a/board/amcc/acadia/cpr.c b/board/amcc/acadia/pll.c
index 9dcce35c89..9dcce35c89 100644
--- a/board/amcc/acadia/cpr.c
+++ b/board/amcc/acadia/pll.c
diff --git a/board/amcc/bamboo/bamboo.c b/board/amcc/bamboo/bamboo.c
index 2e651df3b7..caf66909b9 100644
--- a/board/amcc/bamboo/bamboo.c
+++ b/board/amcc/bamboo/bamboo.c
@@ -416,7 +416,7 @@ int testdram(void)
  *	certain pre-initialization actions.
  *
  ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT)
+#if defined(CONFIG_PCI)
 int pci_pre_init(struct pci_controller *hose)
 {
 	unsigned long addr;
@@ -457,7 +457,7 @@ int pci_pre_init(struct pci_controller *hose)
 
 	return 1;
 }
-#endif				/* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */
+#endif /* defined(CONFIG_PCI) */
 
 /*************************************************************************
  *  pci_target_init
diff --git a/board/amcc/ebony/ebony.c b/board/amcc/ebony/ebony.c
index dcafac950d..ededb3e7e1 100644
--- a/board/amcc/ebony/ebony.c
+++ b/board/amcc/ebony/ebony.c
@@ -207,14 +207,14 @@ long int fixed_sdram(void)
  *	certain pre-initialization actions.
  *
  ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT)
+#if defined(CONFIG_PCI)
 int pci_pre_init(struct pci_controller *hose)
 {
 	unsigned long strap;
 
 	/*--------------------------------------------------------------------------+
-     *	The ebony board is always configured as the host & requires the
-     *	PCI arbiter to be enabled.
+	 * The ebony board is always configured as the host & requires the
+	 * PCI arbiter to be enabled.
 	 *--------------------------------------------------------------------------*/
 	strap = mfdcr(cpc0_strp1);
 	if ((strap & 0x00100000) == 0) {
@@ -224,7 +224,7 @@ int pci_pre_init(struct pci_controller *hose)
 
 	return 1;
 }
-#endif				/* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */
+#endif	/* defined(CONFIG_PCI) */
 
 /*************************************************************************
  *  pci_target_init
diff --git a/board/amcc/katmai/katmai.c b/board/amcc/katmai/katmai.c
index 286bdc1f21..b804d55f2e 100644
--- a/board/amcc/katmai/katmai.c
+++ b/board/amcc/katmai/katmai.c
@@ -292,7 +292,7 @@ int testdram (void)
  *	certain pre-initialization actions.
  *
  ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT)
+#if defined(CONFIG_PCI)
 int pci_pre_init(struct pci_controller * hose )
 {
 	unsigned long strap;
@@ -309,7 +309,7 @@ int pci_pre_init(struct pci_controller * hose )
 
 	return 1;
 }
-#endif	/* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */
+#endif	/* defined(CONFIG_PCI) */
 
 /*************************************************************************
  *  pci_target_init
diff --git a/board/amcc/luan/luan.c b/board/amcc/luan/luan.c
index 778aafc766..2eff3b33fd 100644
--- a/board/amcc/luan/luan.c
+++ b/board/amcc/luan/luan.c
@@ -161,7 +161,7 @@ int testdram(void)
  *	certain pre-initialization actions.
  *
  ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT)
+#if defined(CONFIG_PCI)
 int pci_pre_init( struct pci_controller *hose )
 {
 	unsigned long strap;
@@ -179,7 +179,7 @@ int pci_pre_init( struct pci_controller *hose )
 
 	return  1;
 }
-#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */
+#endif /* defined(CONFIG_PCI) */
 
 
 /*************************************************************************
diff --git a/board/amcc/ocotea/ocotea.c b/board/amcc/ocotea/ocotea.c
index 3f6d2042d7..3bd1b81400 100644
--- a/board/amcc/ocotea/ocotea.c
+++ b/board/amcc/ocotea/ocotea.c
@@ -306,7 +306,7 @@ long int fixed_sdram (void)
  *	certain pre-initialization actions.
  *
  ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT)
+#if defined(CONFIG_PCI)
 int pci_pre_init(struct pci_controller * hose )
 {
 	unsigned long strap;
@@ -323,7 +323,7 @@ int pci_pre_init(struct pci_controller * hose )
 
 	return 1;
 }
-#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */
+#endif /* defined(CONFIG_PCI) */
 
 /*************************************************************************
  *  pci_target_init
diff --git a/board/amcc/sequoia/Makefile b/board/amcc/sequoia/Makefile
index 06ef7f9331..e1c9ad4d69 100644
--- a/board/amcc/sequoia/Makefile
+++ b/board/amcc/sequoia/Makefile
@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= $(obj)lib$(BOARD).a
 
-COBJS	= $(BOARD).o sdram.o
+COBJS	= $(BOARD).o cmd_sequoia.o sdram.o
 SOBJS	= init.o
 
 SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
diff --git a/board/amcc/sequoia/cmd_sequoia.c b/board/amcc/sequoia/cmd_sequoia.c
new file mode 100644
index 0000000000..6fc60eaaa2
--- /dev/null
+++ b/board/amcc/sequoia/cmd_sequoia.c
@@ -0,0 +1,111 @@
+/*
+ * (C) Copyright 2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <common.h>
+#include <command.h>
+#include <i2c.h>
+
+static u8 boot_533_nor[] = {
+	0x87, 0x78, 0x82, 0x52, 0x09, 0x57, 0xa0, 0x30,
+	0x40, 0x08, 0x23, 0x50, 0x0d, 0x05, 0x00, 0x00
+};
+
+static u8 boot_533_nand[] = {
+	0x87, 0x78, 0x82, 0x52, 0x09, 0x57, 0xd0, 0x10,
+	0xa0, 0x68, 0x23, 0x58, 0x0d, 0x05, 0x00, 0x00
+};
+
+static u8 boot_667_nor[] = {
+	0x87, 0x78, 0xa2, 0x52, 0x09, 0xd7, 0xa0, 0x30,
+	0x40, 0x08, 0x23, 0x50, 0x0d, 0x05, 0x00, 0x00
+};
+
+static u8 boot_667_nand[] = {
+	0x87, 0x78, 0xa2, 0x52, 0x09, 0xd7, 0xd0, 0x10,
+	0xa0, 0x68, 0x23, 0x58, 0x0d, 0x05, 0x00, 0x00
+};
+
+static int do_bootstrap(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	u8 chip;
+	u8 *buf;
+	int cpu_freq;
+
+	if (argc < 3) {
+		printf("Usage:\n%s\n", cmdtp->usage);
+		return 1;
+	}
+
+	cpu_freq = simple_strtol(argv[1], NULL, 10);
+	if (!((cpu_freq == 533) || (cpu_freq == 667))) {
+		printf("Unsupported cpu-frequency - only 533 and 667 supported\n");
+		return 1;
+	}
+
+	/* use 0x52 as I2C EEPROM address for now */
+	chip = 0x52;
+
+	if ((strcmp(argv[2], "nor") != 0) &&
+	    (strcmp(argv[2], "nand") != 0)) {
+		printf("Unsupported boot-device - only nor|nand support\n");
+		return 1;
+	}
+
+	if (strcmp(argv[2], "nand") == 0) {
+		switch (cpu_freq) {
+		default:
+		case 533:
+			buf = boot_533_nand;
+			break;
+		case 667:
+			buf = boot_667_nand;
+			break;
+		}
+	} else {
+		switch (cpu_freq) {
+		default:
+		case 533:
+			buf = boot_533_nor;
+			break;
+		case 667:
+			buf = boot_667_nor;
+			break;
+		}
+	}
+
+	if (i2c_write(chip, 0, 1, buf, 16) != 0)
+		printf("Error writing to EEPROM at address 0x%x\n", chip);
+	udelay(CFG_EEPROM_PAGE_WRITE_DELAY_MS * 1000);
+
+	printf("Done\n");
+	printf("Please power-cycle the board for the changes to take effect\n");
+
+	return 0;
+}
+
+U_BOOT_CMD(
+	bootstrap,	3,	0,	do_bootstrap,
+	"bootstrap - program the I2C bootstrap EEPROM\n",
+	"<cpu-freq> <nor|nand> - program the I2C bootstrap EEPROM\n"
+	);
diff --git a/board/amcc/sequoia/sequoia.c b/board/amcc/sequoia/sequoia.c
index ba365aea31..f823117687 100644
--- a/board/amcc/sequoia/sequoia.c
+++ b/board/amcc/sequoia/sequoia.c
@@ -25,7 +25,6 @@
 #include <common.h>
 #include <asm/processor.h>
 #include <ppc440.h>
-#include "sequoia.h"
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -226,7 +225,7 @@ int misc_init_r(void)
 	if (act == NULL || strcmp(act, "hostdev") == 0)	{
 		/* SDR Setting */
 		mfsdr(SDR0_PFC1, sdr0_pfc1);
-		mfsdr(SDR0_USB0, usb2d0cr);
+		mfsdr(SDR0_USB2D0CR, usb2d0cr);
 		mfsdr(SDR0_USB2PHY0CR, usb2phy0cr);
 		mfsdr(SDR0_USB2H0CR, usb2h0cr);
 
@@ -254,7 +253,7 @@ int misc_init_r(void)
 		sdr0_pfc1 = sdr0_pfc1 | SDR0_PFC1_UES_USB2D_SEL;		/*0*/
 
 		mtsdr(SDR0_PFC1, sdr0_pfc1);
-		mtsdr(SDR0_USB0, usb2d0cr);
+		mtsdr(SDR0_USB2D0CR, usb2d0cr);
 		mtsdr(SDR0_USB2PHY0CR, usb2phy0cr);
 		mtsdr(SDR0_USB2H0CR, usb2h0cr);
 
@@ -298,7 +297,7 @@ int misc_init_r(void)
 		/* SDR Setting */
 		mfsdr(SDR0_USB2PHY0CR, usb2phy0cr);
 		mfsdr(SDR0_USB2H0CR, usb2h0cr);
-		mfsdr(SDR0_USB0, usb2d0cr);
+		mfsdr(SDR0_USB2D0CR, usb2d0cr);
 		mfsdr(SDR0_PFC1, sdr0_pfc1);
 
 		usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_XOCLK_MASK;
@@ -323,7 +322,7 @@ int misc_init_r(void)
 
 		mtsdr(SDR0_USB2H0CR, usb2h0cr);
 		mtsdr(SDR0_USB2PHY0CR, usb2phy0cr);
-		mtsdr(SDR0_USB0, usb2d0cr);
+		mtsdr(SDR0_USB2D0CR, usb2d0cr);
 		mtsdr(SDR0_PFC1, sdr0_pfc1);
 
 		/*clear resets*/
@@ -426,23 +425,10 @@ int testdram(void)
  *	certain pre-initialization actions.
  *
  ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT)
+#if defined(CONFIG_PCI)
 int pci_pre_init(struct pci_controller *hose)
 {
 	unsigned long addr;
-#if 0
-	/*--------------------------------------------------------------------------+
-	 *	Cactus is always configured as the host & requires the
-	 *	PCI arbiter to be enabled ???
-	 *--------------------------------------------------------------------------*/
-	unsigned long strap;
-	mfsdr(sdr_sdstp1, strap);
-	if ((strap & SDR0_SDSTP1_PAE_MASK) == 0) {
-		printf("PCI: SDR0_STRP1[PAE] not set.\n");
-		printf("PCI: Configuration aborted.\n");
-		return 0;
-	}
-#endif
 
 	/*-------------------------------------------------------------------------+
 	  | Set priority for all PLB3 devices to 0.
@@ -480,7 +466,7 @@ int pci_pre_init(struct pci_controller *hose)
 
 	return 1;
 }
-#endif				/* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */
+#endif /* defined(CONFIG_PCI) */
 
 /*************************************************************************
  *  pci_target_init
@@ -586,3 +572,13 @@ int is_pci_host(struct pci_controller *hose)
 	return (1);
 }
 #endif				/* defined(CONFIG_PCI) */
+#if defined(CONFIG_POST)
+/*
+ * Returns 1 if keys pressed to start the power-on long-running tests
+ * Called from board_init_f().
+ */
+int post_hotkeys_pressed(void)
+{
+	return 0;	/* No hotkeys supported */
+}
+#endif /* CONFIG_POST */
diff --git a/board/amcc/sequoia/sequoia.h b/board/amcc/sequoia/sequoia.h
deleted file mode 100644
index 1d44b16464..0000000000
--- a/board/amcc/sequoia/sequoia.h
+++ /dev/null
@@ -1,67 +0,0 @@
-/*
- * (C) Copyright 2006
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * (C) Copyright 2006
- * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com
- * Alain Saurel,            AMCC/IBM, alain.saurel@fr.ibm.com
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-
-/*----------------------------------------------------------------------------+
-  | EBC Configuration Register - EBC0_CFG
-  +----------------------------------------------------------------------------*/
-/* External Bus Three-State Control */
-#define EBC0_CFG_EBTC_DRIVEN	    0x80000000
-/* Device-Paced Time-out Disable */
-#define EBC0_CFG_PTD_ENABLED	    0x00000000
-/* Ready Timeout Count */
-#define EBC0_CFG_RTC_MASK	    0x38000000
-#define EBC0_CFG_RTC_16PERCLK	    0x00000000
-#define EBC0_CFG_RTC_32PERCLK	    0x08000000
-#define EBC0_CFG_RTC_64PERCLK	    0x10000000
-#define EBC0_CFG_RTC_128PERCLK	    0x18000000
-#define EBC0_CFG_RTC_256PERCLK	    0x20000000
-#define EBC0_CFG_RTC_512PERCLK	    0x28000000
-#define EBC0_CFG_RTC_1024PERCLK	    0x30000000
-#define EBC0_CFG_RTC_2048PERCLK	    0x38000000
-/* External Master Priority Low */
-#define EBC0_CFG_EMPL_LOW	    0x00000000
-#define EBC0_CFG_EMPL_MEDIUM_LOW    0x02000000
-#define EBC0_CFG_EMPL_MEDIUM_HIGH   0x04000000
-#define EBC0_CFG_EMPL_HIGH	    0x06000000
-/* External Master Priority High */
-#define EBC0_CFG_EMPH_LOW	    0x00000000
-#define EBC0_CFG_EMPH_MEDIUM_LOW    0x00800000
-#define EBC0_CFG_EMPH_MEDIUM_HIGH   0x01000000
-#define EBC0_CFG_EMPH_HIGH	    0x01800000
-/* Chip Select Three-State Control */
-#define EBC0_CFG_CSTC_DRIVEN	    0x00400000
-/* Burst Prefetch */
-#define EBC0_CFG_BPF_ONEDW	    0x00000000
-#define EBC0_CFG_BPF_TWODW	    0x00100000
-#define EBC0_CFG_BPF_FOURDW	    0x00200000
-/* External Master Size */
-#define EBC0_CFG_EMS_8BIT	    0x00000000
-/* Power Management Enable */
-#define EBC0_CFG_PME_DISABLED	    0x00000000
-#define EBC0_CFG_PME_ENABLED	    0x00020000
-/* Power Management Timer */
-#define EBC0_CFG_PMT_ENCODE(n)		((((unsigned long)(n))&0x1F)<<12)
-
-#define SDR0_USB0                    0x0320     /* USB Control Register */
diff --git a/board/amcc/taishan/taishan.c b/board/amcc/taishan/taishan.c
index 1a2e53b1ab..bc976c7526 100644
--- a/board/amcc/taishan/taishan.c
+++ b/board/amcc/taishan/taishan.c
@@ -236,7 +236,7 @@ int testdram (void)
  *	certain pre-initialization actions.
  *
  ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT)
+#if defined(CONFIG_PCI)
 int pci_pre_init(struct pci_controller * hose )
 {
 	unsigned long strap;
@@ -253,7 +253,7 @@ int pci_pre_init(struct pci_controller * hose )
 
 	return 1;
 }
-#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */
+#endif /* defined(CONFIG_PCI) */
 
 /*************************************************************************
  *  pci_target_init
diff --git a/board/amcc/yosemite/yosemite.c b/board/amcc/yosemite/yosemite.c
index c2e12ba12e..912f09ee43 100644
--- a/board/amcc/yosemite/yosemite.c
+++ b/board/amcc/yosemite/yosemite.c
@@ -385,7 +385,7 @@ int testdram(void)
  *	certain pre-initialization actions.
  *
  ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT)
+#if defined(CONFIG_PCI)
 int pci_pre_init(struct pci_controller *hose)
 {
 	unsigned long addr;
@@ -426,7 +426,7 @@ int pci_pre_init(struct pci_controller *hose)
 
 	return 1;
 }
-#endif				/* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */
+#endif	/* defined(CONFIG_PCI) */
 
 /*************************************************************************
  *  pci_target_init
diff --git a/board/amcc/yucca/yucca.c b/board/amcc/yucca/yucca.c
index 90eaab1c80..7316c34b4a 100644
--- a/board/amcc/yucca/yucca.c
+++ b/board/amcc/yucca/yucca.c
@@ -604,7 +604,7 @@ int testdram (void)
  *	certain pre-initialization actions.
  *
  ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT)
+#if defined(CONFIG_PCI)
 int pci_pre_init(struct pci_controller * hose )
 {
 	unsigned long strap;
@@ -621,7 +621,7 @@ int pci_pre_init(struct pci_controller * hose )
 
 	return 1;
 }
-#endif	/* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */
+#endif	/* defined(CONFIG_PCI) */
 
 /*************************************************************************
  *  pci_target_init
diff --git a/board/bf537-stamp/ether_bf537.c b/board/bf537-stamp/ether_bf537.c
index f00837aad2..807b9e839b 100644
--- a/board/bf537-stamp/ether_bf537.c
+++ b/board/bf537-stamp/ether_bf537.c
@@ -48,7 +48,7 @@
 #define TXBUF_BASE_ADDR		0xFF800000
 #define TX_BUF_CNT		1
 
-#define TOUT_LOOP 		1000000
+#define TOUT_LOOP		1000000
 
 ADI_ETHER_BUFFER *txbuf[TX_BUF_CNT];
 ADI_ETHER_BUFFER *rxbuf[PKTBUFSRX];
diff --git a/board/bf537-stamp/flash-defines.h b/board/bf537-stamp/flash-defines.h
index acc1e8638b..1fa7a10bda 100644
--- a/board/bf537-stamp/flash-defines.h
+++ b/board/bf537-stamp/flash-defines.h
@@ -44,9 +44,9 @@
 #define ERASE_SECT		6
 #define READ			7
 #define GET_SECTNUM		8
-#define FLASH_START_L 		0x0000
-#define FLASH_START_H 		0x2000
-#define FLASH_MAN_ST 		2
+#define FLASH_START_L		0x0000
+#define FLASH_START_H		0x2000
+#define FLASH_MAN_ST		2
 #define RESET_VAL		0xF0
 
 flash_info_t flash_info[CFG_MAX_FLASH_BANKS];
diff --git a/board/bf537-stamp/stm_m25p64.c b/board/bf537-stamp/stm_m25p64.c
index 7077e85f41..d9c08ee8e6 100644
--- a/board/bf537-stamp/stm_m25p64.c
+++ b/board/bf537-stamp/stm_m25p64.c
@@ -9,7 +9,7 @@
 
 /* Application definitions */
 
-#define	NUM_SECTORS 	128	/* number of sectors */
+#define	NUM_SECTORS	128	/* number of sectors */
 #define SECTOR_SIZE	0x10000
 #define NOP_NUM		1000
 
diff --git a/board/bf537-stamp/u-boot.lds.S b/board/bf537-stamp/u-boot.lds.S
index 3fb2d0cc60..8632097b61 100644
--- a/board/bf537-stamp/u-boot.lds.S
+++ b/board/bf537-stamp/u-boot.lds.S
@@ -33,7 +33,7 @@ SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib);
    __DYNAMIC = 0;    */
 MEMORY
  {
- ram : 	   ORIGIN = (CFG_MONITOR_BASE), LENGTH = (256 * 1024)
+ ram :	   ORIGIN = (CFG_MONITOR_BASE), LENGTH = (256 * 1024)
  l1_code : ORIGIN = 0xFFA00000, LENGTH = 0xC000
  l1_data : ORIGIN = 0xFF900000, LENGTH = 0x4000
  }
@@ -47,11 +47,11 @@ SECTIONS
   .dynsym        : { *(.dynsym)		}
   .dynstr        : { *(.dynstr)		}
   .rel.text      : { *(.rel.text)	}
-  .rela.text     : { *(.rela.text) 	}
+  .rela.text     : { *(.rela.text)	}
   .rel.data      : { *(.rel.data)	}
-  .rela.data     : { *(.rela.data) 	}
-  .rel.rodata    : { *(.rel.rodata) 	}
-  .rela.rodata   : { *(.rela.rodata) 	}
+  .rela.data     : { *(.rela.data)	}
+  .rel.rodata    : { *(.rel.rodata)	}
+  .rela.rodata   : { *(.rela.rodata)	}
   .rel.got       : { *(.rel.got)	}
   .rela.got      : { *(.rela.got)	}
   .rel.ctors     : { *(.rel.ctors)	}
@@ -68,7 +68,7 @@ SECTIONS
   .text      :
   {
     /* WARNING - the following is hand-optimized to fit within	*/
-    /* the sector before the environment sector. If it throws 	*/
+    /* the sector before the environment sector. If it throws	*/
     /* an error during compilation remove an object here to get	*/
     /* it linked after the configuration sector.		*/
 
diff --git a/board/cds/mpc8548cds/mpc8548cds.c b/board/cds/mpc8548cds/mpc8548cds.c
index 929ff2e662..b7236417e8 100644
--- a/board/cds/mpc8548cds/mpc8548cds.c
+++ b/board/cds/mpc8548cds/mpc8548cds.c
@@ -345,23 +345,23 @@ int last_stage_init(void)
 	/* This is needed to get the RGMII working for the 1.3+
 	 * CDS cards */
 	if (get_board_version() ==  0x13) {
-		miiphy_write(CONFIG_MPC85XX_TSEC1_NAME,
+		miiphy_write(CONFIG_TSEC1_NAME,
 				TSEC1_PHY_ADDR, 29, 18);
 
-		miiphy_read(CONFIG_MPC85XX_TSEC1_NAME,
+		miiphy_read(CONFIG_TSEC1_NAME,
 				TSEC1_PHY_ADDR, 30, &temp);
 
 		temp = (temp & 0xf03f);
 		temp |= 2 << 9;		/* 36 ohm */
 		temp |= 2 << 6;		/* 39 ohm */
 
-		miiphy_write(CONFIG_MPC85XX_TSEC1_NAME,
+		miiphy_write(CONFIG_TSEC1_NAME,
 				TSEC1_PHY_ADDR, 30, temp);
 
-		miiphy_write(CONFIG_MPC85XX_TSEC1_NAME,
+		miiphy_write(CONFIG_TSEC1_NAME,
 				TSEC1_PHY_ADDR, 29, 3);
 
-		miiphy_write(CONFIG_MPC85XX_TSEC1_NAME,
+		miiphy_write(CONFIG_TSEC1_NAME,
 				TSEC1_PHY_ADDR, 30, 0x8000);
 	}
 
diff --git a/board/cm1_qp1/Makefile b/board/cm1_qp1/Makefile
new file mode 100644
index 0000000000..e7393267e7
--- /dev/null
+++ b/board/cm1_qp1/Makefile
@@ -0,0 +1,50 @@
+#
+# (C) Copyright 2003-2007
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS	:= $(BOARD).o cmd_cm1_qp1.o fwupdate.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/cm1_qp1/cm1_qp1.c b/board/cm1_qp1/cm1_qp1.c
new file mode 100644
index 0000000000..b49298f64b
--- /dev/null
+++ b/board/cm1_qp1/cm1_qp1.c
@@ -0,0 +1,222 @@
+/*
+ * (C) Copyright 2003-2007
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * (C) Copyright 2004
+ * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
+ *
+ * (C) Copyright 2004-2005
+ * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <mpc5xxx.h>
+#include <pci.h>
+#include <asm/processor.h>
+#include <i2c.h>
+#ifdef CONFIG_OF_FLAT_TREE
+#include <ft_build.h>
+#endif /* CONFIG_OF_FLAT_TREE */
+
+#include "fwupdate.h"
+
+#ifndef CFG_RAMBOOT
+/*
+ * Helper function to initialize SDRAM controller.
+ */
+static void sdram_start(int hi_addr)
+{
+	long hi_addr_bit = hi_addr ? 0x01000000 : 0;
+
+	/* unlock mode register */
+	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000000 |
+						hi_addr_bit;
+
+	/* precharge all banks */
+	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 |
+						hi_addr_bit;
+
+	/* auto refresh */
+	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000004 |
+						hi_addr_bit;
+
+	/* auto refresh, second time */
+	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000004 |
+						hi_addr_bit;
+
+	/* set mode register */
+	*(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_MODE;
+
+	/* normal operation */
+	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | hi_addr_bit;
+}
+#endif /* CFG_RAMBOOT */
+
+/*
+ * Initalize SDRAM - configure SDRAM controller, detect memory size.
+ */
+long int initdram(int board_type)
+{
+	ulong dramsize = 0;
+#ifndef CFG_RAMBOOT
+	ulong test1, test2;
+
+	/* configure SDRAM start/end for detection */
+	*(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x0000001e; /* 2G at 0x0 */
+
+	/* setup config registers */
+	*(vu_long *)MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1;
+	*(vu_long *)MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2;
+
+	sdram_start(0);
+	test1 = get_ram_size((long *)CFG_SDRAM_BASE, 0x80000000);
+	sdram_start(1);
+	test2 = get_ram_size((long *)CFG_SDRAM_BASE, 0x80000000);
+	if (test1 > test2) {
+		sdram_start(0);
+		dramsize = test1;
+	} else
+		dramsize = test2;
+
+	/* memory smaller than 1MB is impossible */
+	if (dramsize < (1 << 20))
+		dramsize = 0;
+
+	/* set SDRAM CS0 size according to the amount of RAM found */
+	if (dramsize > 0) {
+		*(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x13 +
+			__builtin_ffs(dramsize >> 20) - 1;
+	} else
+		*(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0; /* disabled */
+#else /* CFG_RAMBOOT */
+	/* retrieve size of memory connected to SDRAM CS0 */
+	dramsize = *(vu_long *)MPC5XXX_SDRAM_CS0CFG & 0xFF;
+	if (dramsize >= 0x13)
+		dramsize = (1 << (dramsize - 0x13)) << 20;
+	else
+		dramsize = 0;
+#endif /* CFG_RAMBOOT */
+
+	/*
+	 * On MPC5200B we need to set the special configuration delay in the
+	 * DDR controller.  Refer to chapter 8.7.5 SDelay--MBAR + 0x0190 of
+	 * the MPC5200B User's Manual.
+	 */
+	*(vu_long *)MPC5XXX_SDRAM_SDELAY = 0x04;
+	__asm__ volatile ("sync");
+
+	return dramsize;
+}
+
+
+int checkboard(void)
+{
+	puts("Board: CM1.QP1\n");
+	return 0;
+}
+
+
+int board_early_init_r(void)
+{
+	/*
+	 * Now, when we are in RAM, enable flash write access for detection
+	 * process. Note that CS_BOOT cannot be cleared when executing in
+	 * flash.
+	 */
+	*(vu_long *)MPC5XXX_BOOTCS_CFG &= ~0x1; /* clear RO */
+	return 0;
+}
+
+
+#ifdef CONFIG_POST
+int post_hotkeys_pressed(void)
+{
+	return 0;
+}
+#endif /* CONFIG_POST */
+
+
+#if defined(CONFIG_POST) || defined(CONFIG_LOGBUFFER)
+void post_word_store(ulong a)
+{
+	vu_long *save_addr = (vu_long *)(MPC5XXX_SRAM + MPC5XXX_SRAM_POST_SIZE);
+	*save_addr = a;
+}
+
+
+ulong post_word_load(void)
+{
+	vu_long *save_addr = (vu_long *)(MPC5XXX_SRAM + MPC5XXX_SRAM_POST_SIZE);
+	return *save_addr;
+}
+#endif /* CONFIG_POST || CONFIG_LOGBUFFER */
+
+
+#ifdef CONFIG_MISC_INIT_R
+int misc_init_r(void)
+{
+#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C)
+	uchar buf[6];
+	char str[18];
+
+	/* Read ethaddr from EEPROM */
+	if (i2c_read(CFG_I2C_EEPROM, CONFIG_MAC_OFFSET, 2, buf, 6) == 0) {
+		sprintf(str, "%02X:%02X:%02X:%02X:%02X:%02X",
+			buf[0], buf[1], buf[2], buf[3], buf[4], buf[5]);
+		/* Check if MAC addr is owned by Schindler */
+		if (strstr(str, "00:06:C3") != str) {
+			printf(LOG_PREFIX "Warning - Illegal MAC address (%s)"
+				" in EEPROM.\n", str);
+			printf(LOG_PREFIX "Using MAC from environment\n");
+		} else {
+			printf(LOG_PREFIX "Using MAC (%s) from I2C EEPROM\n",
+				str);
+			setenv("ethaddr", str);
+		}
+	} else {
+		printf(LOG_PREFIX "Warning - Unable to read MAC from I2C"
+			" device at address %02X:%04X\n", CFG_I2C_EEPROM,
+			CONFIG_MAC_OFFSET);
+		printf(LOG_PREFIX "Using MAC from environment\n");
+	}
+	return 0;
+#endif /* defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) */
+}
+#endif /* CONFIG_MISC_INIT_R */
+
+
+#ifdef CONFIG_LAST_STAGE_INIT
+int last_stage_init(void)
+{
+#ifdef CONFIG_USB_STORAGE
+	cm1_fwupdate();
+#endif /* CONFIG_USB_STORAGE */
+	return 0;
+}
+#endif /* CONFIG_LAST_STAGE_INIT */
+
+
+#if defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+	ft_cpu_setup(blob, bd);
+}
+#endif /* defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP) */
diff --git a/board/cm1_qp1/cmd_cm1_qp1.c b/board/cm1_qp1/cmd_cm1_qp1.c
new file mode 100644
index 0000000000..4a01d2a7f4
--- /dev/null
+++ b/board/cm1_qp1/cmd_cm1_qp1.c
@@ -0,0 +1,446 @@
+/*
+ *  (C) Copyright 2007 Markus Kappeler <markus.kappeler@objectxp.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <i2c.h>
+#include <usb.h>
+
+#if (CONFIG_COMMANDS & CFG_CMD_BSP)
+
+int do_i2c(char *argv[])
+{
+	unsigned char temp, temp1;
+
+	printf("Starting I2C Test\n"
+		"Please set Jumper:\nI2C SDA 2-3\nI2C SCL 2-3\n\n"
+		"Please press any key to start\n\n");
+	getc();
+
+	temp = 0xf0; /* set io 0-4 as output */
+	i2c_write(CFG_I2C_IO, 3, 1, (uchar *)&temp, 1);
+
+	printf("Press I2C4-7. LED I2C0-3 should have the same state\n\n"
+		"Press any key to stop\n\n");
+
+	while (!tstc()) {
+		i2c_read(CFG_I2C_IO, 0, 1, (uchar *)&temp, 1);
+		temp1 = (temp >> 4) & 0x03;
+		temp1 |= (temp >> 3) & 0x08; /* S302 -> LED303 */
+		temp1 |= (temp >> 5) & 0x04; /* S303 -> LED302 */
+		temp = temp1;
+		i2c_write(CFG_I2C_IO, 1, 1, (uchar *)&temp, 1);
+	}
+	getc();
+
+	return 0;
+}
+
+int do_usbtest(char *argv[])
+{
+	int i;
+	static int usb_stor_curr_dev = -1; /* current device */
+
+	printf("Starting USB Test\n"
+		"Please insert USB Memmory Stick\n\n"
+		"Please press any key to start\n\n");
+	getc();
+
+	usb_stop();
+	printf("(Re)start USB...\n");
+	i = usb_init();
+#ifdef CONFIG_USB_STORAGE
+		/* try to recognize storage devices immediately */
+		if (i >= 0)
+			usb_stor_curr_dev = usb_stor_scan(1);
+#endif /* CONFIG_USB_STORAGE */
+	if (usb_stor_curr_dev >= 0)
+		printf("Found USB Storage Dev continue with Test...\n");
+	else {
+		printf("No USB Storage Device detected.. Stop Test\n");
+		return 1;
+	}
+
+	usb_stor_info();
+
+	printf("stopping USB..\n");
+	usb_stop();
+
+	return 0;
+}
+
+int do_led(char *argv[])
+{
+	int i = 0;
+	struct mpc5xxx_gpt_0_7 *gpt = (struct mpc5xxx_gpt_0_7 *)MPC5XXX_GPT;
+
+	printf("Starting LED Test\n"
+		"Please set Switch S500 all off\n\n"
+		"Please press any key to start\n\n");
+	getc();
+
+	/* configure timer 2-3 for simple GPIO output High */
+	gpt->gpt2.emsr |= 0x00000034;
+	gpt->gpt3.emsr |= 0x00000034;
+
+	(*(vu_long *)MPC5XXX_WU_GPIO_ENABLE) |= 0x80000000;
+	(*(vu_long *)MPC5XXX_WU_GPIO_DIR) |= 0x80000000;
+	printf("Please press any key to stop\n\n");
+	while (!tstc()) {
+		if (i == 1) {
+			(*(vu_long *)MPC5XXX_WU_GPIO_DATA_O) |= 0x80000000;
+			gpt->gpt2.emsr &= ~0x00000010;
+			gpt->gpt3.emsr &= ~0x00000010;
+		} else if (i == 2) {
+			(*(vu_long *)MPC5XXX_WU_GPIO_DATA_O) &= ~0x80000000;
+			gpt->gpt2.emsr &= ~0x00000010;
+			gpt->gpt3.emsr |= 0x00000010;
+		} else if (i >= 3) {
+			(*(vu_long *)MPC5XXX_WU_GPIO_DATA_O) &= ~0x80000000;
+			gpt->gpt3.emsr &= ~0x00000010;
+			gpt->gpt2.emsr |= 0x00000010;
+			i = 0;
+		}
+		i++;
+		udelay(200000);
+	}
+	getc();
+
+	(*(vu_long *)MPC5XXX_WU_GPIO_DATA_O) |= 0x80000000;
+	gpt->gpt2.emsr |= 0x00000010;
+	gpt->gpt3.emsr |= 0x00000010;
+
+	return 0;
+}
+
+int do_rs232(char *argv[])
+{
+	int error_status = 0;
+	struct mpc5xxx_gpio *gpio = (struct mpc5xxx_gpio *)MPC5XXX_GPIO;
+	struct mpc5xxx_psc *psc1 = (struct mpc5xxx_psc *)MPC5XXX_PSC1;
+
+	/* Configure PSC 2-3-6 as GPIO */
+	gpio->port_config &= 0xFF0FF80F;
+
+	switch (simple_strtoul(argv[2], NULL, 10)) {
+	case 1:
+		/* check RTS <-> CTS loop */
+		/* set rts to 0 */
+		printf("Uart 1 test: RX TX tested by using U-Boot\n"
+			"Please connect RTS with CTS on Uart1 plug\n\n"
+			"Press any key to start\n\n");
+		getc();
+
+		psc1->op1 |= 0x01;
+
+		/* wait some time before requesting status */
+		udelay(10);
+
+		/* check status at cts */
+		if ((psc1->ip & 0x01) != 0) {
+			error_status = 3;
+			printf("%s: failure at rs232_1, cts status is %d "
+				"(should be 0)\n",
+				__FUNCTION__, (psc1->ip & 0x01));
+		}
+
+		/* set rts to 1 */
+		psc1->op0 |= 0x01;
+
+		/* wait some time before requesting status */
+		udelay(10);
+
+		/* check status at cts */
+		if ((psc1->ip & 0x01) != 1) {
+			error_status = 3;
+			printf("%s: failure at rs232_1, cts status is %d "
+				"(should be 1)\n",
+				__FUNCTION__, (psc1->ip & 0x01));
+		}
+		break;
+	case 2:
+		/* set PSC2_0, PSC2_2 as output and PSC2_1, PSC2_3 as input */
+		printf("Uart 2 test: Please use RS232 Loopback plug on UART2\n"
+			"\nPress any key to start\n\n");
+		getc();
+
+		gpio->simple_gpioe &= ~(0x000000F0);
+		gpio->simple_gpioe |= 0x000000F0;
+		gpio->simple_ddr &= ~(0x000000F0);
+		gpio->simple_ddr |= 0x00000050;
+
+		/* check TXD <-> RXD loop */
+		/* set TXD to 1 */
+		gpio->simple_dvo |= (1 << 4);
+
+		/* wait some time before requesting status */
+		udelay(10);
+
+		if ((gpio->simple_ival & 0x00000020) != 0x00000020) {
+			error_status = 2;
+			printf("%s: failure at rs232_2, rxd status is %d "
+				"(should be 1)\n", __FUNCTION__,
+				(gpio->simple_ival & 0x00000020) >> 5);
+		}
+
+		/* set TXD to 0 */
+		gpio->simple_dvo &= ~(1 << 4);
+
+		/* wait some time before requesting status */
+		udelay(10);
+
+		if ((gpio->simple_ival & 0x00000020) != 0x00000000) {
+			error_status = 2;
+			printf("%s: failure at rs232_2, rxd status is %d "
+				"(should be 0)\n", __FUNCTION__,
+				(gpio->simple_ival & 0x00000020) >> 5);
+		}
+
+		/* check RTS <-> CTS loop */
+		/* set RTS to 1 */
+		gpio->simple_dvo |= (1 << 6);
+
+		/* wait some time before requesting status */
+		udelay(10);
+
+		if ((gpio->simple_ival & 0x00000080) != 0x00000080) {
+			error_status = 3;
+			printf("%s: failure at rs232_2, cts status is %d "
+				"(should be 1)\n", __FUNCTION__,
+				(gpio->simple_ival & 0x00000080) >> 7);
+		}
+
+		/* set RTS to 0 */
+		gpio->simple_dvo &= ~(1 << 6);
+
+		/* wait some time before requesting status */
+		udelay(10);
+
+		if ((gpio->simple_ival & 0x00000080) != 0x00000000) {
+			error_status = 3;
+			printf("%s: failure at rs232_2, cts status is %d "
+				"(should be 0)\n", __FUNCTION__,
+				(gpio->simple_ival & 0x00000080) >> 7);
+		}
+		break;
+	case 3:
+		/* set PSC3_0, PSC3_2 as output and PSC3_1, PSC3_3 as input */
+		printf("Uart 3 test: Please use RS232 Loopback plug on UART2\n"
+			"\nPress any key to start\n\n");
+		getc();
+
+		gpio->simple_gpioe &= ~(0x00000F00);
+		gpio->simple_gpioe |= 0x00000F00;
+
+		gpio->simple_ddr &= ~(0x00000F00);
+		gpio->simple_ddr |= 0x00000500;
+
+		/* check TXD <-> RXD loop */
+		/* set TXD to 1 */
+		gpio->simple_dvo |= (1 << 8);
+
+		/* wait some time before requesting status */
+		udelay(10);
+
+		if ((gpio->simple_ival & 0x00000200) != 0x00000200) {
+			error_status = 2;
+			printf("%s: failure at rs232_3, rxd status is %d "
+				"(should be 1)\n", __FUNCTION__,
+				(gpio->simple_ival & 0x00000200) >> 9);
+		}
+
+		/* set TXD to 0 */
+		gpio->simple_dvo &= ~(1 << 8);
+
+		/* wait some time before requesting status */
+		udelay(10);
+
+		if ((gpio->simple_ival & 0x00000200) != 0x00000000) {
+			error_status = 2;
+			printf("%s: failure at rs232_3, rxd status is %d "
+				"(should be 0)\n", __FUNCTION__,
+				(gpio->simple_ival & 0x00000200) >> 9);
+		}
+
+		/* check RTS <-> CTS loop */
+		/* set RTS to 1 */
+		gpio->simple_dvo |= (1 << 10);
+
+		/* wait some time before requesting status */
+		udelay(10);
+
+		if ((gpio->simple_ival & 0x00000800) != 0x00000800) {
+			error_status = 3;
+			printf("%s: failure at rs232_3, cts status is %d "
+				"(should be 1)\n", __FUNCTION__,
+				(gpio->simple_ival & 0x00000800) >> 11);
+		}
+
+		/* set RTS to 0 */
+		gpio->simple_dvo &= ~(1 << 10);
+
+		/* wait some time before requesting status */
+		udelay(10);
+
+		if ((gpio->simple_ival & 0x00000800) != 0x00000000) {
+			error_status = 3;
+			printf("%s: failure at rs232_3, cts status is %d "
+				"(should be 0)\n", __FUNCTION__,
+				(gpio->simple_ival & 0x00000800) >> 11);
+		}
+		break;
+	case 4:
+		/* set PSC6_2, PSC6_3 as output and PSC6_0, PSC6_1 as input */
+		printf("Uart 4 test: Please use RS232 Loopback plug on UART2\n"
+			"\nPress any key to start\n\n");
+		getc();
+
+		gpio->simple_gpioe &= ~(0xF0000000);
+		gpio->simple_gpioe |= 0x30000000;
+
+		gpio->simple_ddr &= ~(0xf0000000);
+		gpio->simple_ddr |= 0x30000000;
+
+		(*(vu_long *)MPC5XXX_WU_GPIO_ENABLE) |= 0x30000000;
+		(*(vu_long *)MPC5XXX_WU_GPIO_DIR) &= ~(0x30000000);
+
+		/* check TXD <-> RXD loop */
+		/* set TXD to 1 */
+		gpio->simple_dvo |= (1 << 28);
+
+		/* wait some time before requesting status */
+		udelay(10);
+
+		if (((*(vu_long *)MPC5XXX_WU_GPIO_DATA_I) & 0x10000000) !=
+				0x10000000) {
+			error_status = 2;
+			printf("%s: failure at rs232_4, rxd status is %d "
+				"(should be 1)\n", __FUNCTION__,
+				((*(vu_long *)MPC5XXX_WU_GPIO_DATA_I) &
+					0x10000000) >> 28);
+		}
+
+		/* set TXD to 0 */
+		gpio->simple_dvo &= ~(1 << 28);
+
+		/* wait some time before requesting status */
+		udelay(10);
+
+		if (((*(vu_long *)MPC5XXX_WU_GPIO_DATA_I) & 0x10000000) !=
+				0x00000000) {
+			error_status = 2;
+			printf("%s: failure at rs232_4, rxd status is %d "
+				"(should be 0)\n", __FUNCTION__,
+				((*(vu_long *)MPC5XXX_WU_GPIO_DATA_I) &
+					0x10000000) >> 28);
+		}
+
+		/* check RTS <-> CTS loop */
+		/* set RTS to 1 */
+		gpio->simple_dvo |= (1 << 29);
+
+		/* wait some time before requesting status */
+		udelay(10);
+
+		if (((*(vu_long *)MPC5XXX_WU_GPIO_DATA_I) & 0x20000000) !=
+				0x20000000) {
+			error_status = 3;
+			printf("%s: failure at rs232_4, cts status is %d "
+				"(should be 1)\n", __FUNCTION__,
+				((*(vu_long *)MPC5XXX_WU_GPIO_DATA_I) &
+					0x20000000) >> 29);
+		}
+
+		/* set RTS to 0 */
+		gpio->simple_dvo &= ~(1 << 29);
+
+		/* wait some time before requesting status */
+		udelay(10);
+
+		if (((*(vu_long *)MPC5XXX_WU_GPIO_DATA_I) & 0x20000000) !=
+				0x00000000) {
+			error_status = 3;
+			printf("%s: failure at rs232_4, cts status is %d "
+				"(should be 0)\n", __FUNCTION__,
+				((*(vu_long *)MPC5XXX_WU_GPIO_DATA_I) &
+					0x20000000) >> 29);
+		}
+		break;
+	default:
+		printf("%s: invalid rs232 number %s\n", __FUNCTION__, argv[2]);
+		error_status = 1;
+		break;
+	}
+	gpio->port_config |= (CFG_GPS_PORT_CONFIG & 0xFF0FF80F);
+
+	return error_status;
+}
+
+int cmd_fkt(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	int rcode = -1;
+
+	switch (argc) {
+	case 2:
+		if (strncmp(argv[1], "i2c", 3) == 0)
+			rcode = do_i2c(argv);
+		else if (strncmp(argv[1], "led", 3) == 0)
+			rcode = do_led(argv);
+		else if (strncmp(argv[1], "usb", 3) == 0)
+			rcode = do_usbtest(argv);
+		break;
+	case 3:
+		if (strncmp(argv[1], "rs232", 3) == 0)
+			rcode = do_rs232(argv);
+		break;
+	}
+
+	switch (rcode) {
+	case -1:
+		printf("Usage:\n"
+			"fkt { i2c | led | usb }\n"
+			"fkt rs232 number\n");
+		rcode = 1;
+		break;
+	case 0:
+		printf("Test passed\n");
+		break;
+	default:
+		printf("Test failed with code: %d\n", rcode);
+	}
+
+	return rcode;
+}
+
+U_BOOT_CMD(
+	fkt,	4,	1,	cmd_fkt,
+	"fkt     - Function test routines\n",
+	"i2c\n"
+	"     - Test I2C communication\n"
+	"fkt led\n"
+	"     - Test LEDs\n"
+	"fkt rs232 number\n"
+	"     - Test RS232 (loopback plug(s) for RS232 required)\n"
+	"fkt usb\n"
+	"     - Test USB communication\n"
+);
+#endif /* CFG_CMD_BSP */
diff --git a/board/cm1_qp1/config.mk b/board/cm1_qp1/config.mk
new file mode 100644
index 0000000000..7f061391a2
--- /dev/null
+++ b/board/cm1_qp1/config.mk
@@ -0,0 +1,26 @@
+#
+# (C) Copyright 2007
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+TEXT_BASE = 0xfc000000
+
+PLATFORM_CPPFLAGS += -DTEXT_BASE=$(TEXT_BASE) -I$(TOPDIR)/board
diff --git a/board/cm1_qp1/fwupdate.c b/board/cm1_qp1/fwupdate.c
new file mode 100644
index 0000000000..637375e598
--- /dev/null
+++ b/board/cm1_qp1/fwupdate.c
@@ -0,0 +1,187 @@
+/*
+ * (C) Copyright 2007 Schindler Lift Inc.
+ * (C) Copyright 2007 Semihalf
+ *
+ * Author: Michel Marti <mma@objectxp.com>
+ * Adapted for U-Boot 1.2 by Piotr Kruszynski <ppk@semihalf.com>:
+ * - code clean-up
+ * - bugfix for overwriting bootargs by user
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <malloc.h>
+#include <image.h>
+#include <usb.h>
+#include <fat.h>
+
+#include "fwupdate.h"
+
+extern int do_bootm(cmd_tbl_t *, int, int, char *[]);
+extern long do_fat_read(const char *, void *, unsigned long, int);
+extern int do_fat_fsload(cmd_tbl_t *, int, int, char *[]);
+
+static int load_rescue_image(ulong);
+
+void cm1_fwupdate(void)
+{
+	cmd_tbl_t *bcmd;
+	char *rsargs;
+	char *tmp = NULL;
+	char ka[16];
+	char *argv[3] = { "bootm", ka, NULL };
+
+	/* Check if rescue system is disabled... */
+	if (getenv("norescue")) {
+		printf(LOG_PREFIX "Rescue System disabled.\n");
+		return;
+	}
+
+	/* Check if we have a USB storage device and load image */
+	if (load_rescue_image(LOAD_ADDR))
+		return;
+
+	bcmd = find_cmd("bootm");
+	if (!bcmd)
+		return;
+
+	sprintf(ka, "%lx", LOAD_ADDR);
+
+	/* prepare our bootargs */
+	rsargs = getenv("rs-args");
+	if (!rsargs)
+		rsargs = RS_BOOTARGS;
+	else {
+		tmp = malloc(strlen(rsargs+1));
+		if (!tmp) {
+			printf(LOG_PREFIX "Memory allocation failed\n");
+			return;
+		}
+		strcpy(tmp, rsargs);
+		rsargs = tmp;
+	}
+
+	setenv("bootargs", rsargs);
+
+	if (rsargs == tmp)
+		free(rsargs);
+
+	printf(LOG_PREFIX "Starting update system (bootargs=%s)...\n", rsargs);
+	do_bootm(bcmd, 0, 2, argv);
+}
+
+static int load_rescue_image(ulong addr)
+{
+	disk_partition_t info;
+	int devno;
+	int partno;
+	int i;
+	char fwdir[64];
+	char nxri[128];
+	char *tmp;
+	char dev[7];
+	char addr_str[16];
+	char *argv[6] = { "fatload", "usb", dev, addr_str, nxri, NULL };
+	block_dev_desc_t *stor_dev = NULL;
+	cmd_tbl_t *bcmd;
+
+	/* Get name of firmware directory */
+	tmp = getenv("fw-dir");
+
+	/* Copy it into fwdir */
+	strncpy(fwdir, tmp ? tmp : FW_DIR, sizeof(fwdir));
+	fwdir[sizeof(fwdir) - 1] = 0; /* Terminate string */
+
+	printf(LOG_PREFIX "Checking for firmware image directory '%s' on USB"
+		" storage...\n", fwdir);
+	usb_stop();
+	if (usb_init() != 0)
+		return 1;
+
+	/* Check for storage device */
+	if (usb_stor_scan(1) != 0) {
+		usb_stop();
+		return 1;
+	}
+
+	/* Detect storage device */
+	for (devno = 0; devno < USB_MAX_STOR_DEV; devno++) {
+		stor_dev = usb_stor_get_dev(devno);
+		if (stor_dev->type != DEV_TYPE_UNKNOWN)
+			break;
+	}
+	if (!stor_dev || stor_dev->type == DEV_TYPE_UNKNOWN) {
+		printf(LOG_PREFIX "No valid storage device found...\n");
+		usb_stop();
+		return 1;
+	}
+
+	/* Detect partition */
+	for (partno = -1, i = 0; i < 6; i++) {
+		if (get_partition_info(stor_dev, i, &info) == 0) {
+			if (fat_register_device(stor_dev, i) == 0) {
+				/* Check if rescue image is present */
+				FW_DEBUG("Looking for firmware directory '%s'"
+					" on partition %d\n", fwdir, i);
+				if (do_fat_read(fwdir, NULL, 0, LS_NO) == -1) {
+					FW_DEBUG("No NX rescue image on "
+						"partition %d.\n", i);
+				} else {
+					partno = i;
+					FW_DEBUG("Partition %d contains "
+						"firmware directory\n", partno);
+					break;
+				}
+			}
+		}
+	}
+
+	if (partno == -1) {
+		printf(LOG_PREFIX "Error: No valid (FAT) partition detected\n");
+		usb_stop();
+		return 1;
+	}
+
+	/* Load the rescue image */
+	bcmd = find_cmd("fatload");
+	if (!bcmd) {
+		printf(LOG_PREFIX "Error - 'fatload' command not present.\n");
+		usb_stop();
+		return 1;
+	}
+
+	tmp = getenv("nx-rescue-image");
+	sprintf(nxri, "%s/%s", fwdir, tmp ? tmp : RESCUE_IMAGE);
+	sprintf(dev, "%d:%d", devno, partno);
+	sprintf(addr_str, "%lx", addr);
+
+	FW_DEBUG("fat_fsload device='%s', addr='%s', file: %s\n",
+		dev, addr_str, nxri);
+
+	if (do_fat_fsload(bcmd, 0, 5, argv) != 0) {
+		usb_stop();
+		return 1;
+	}
+
+	/* Stop USB */
+	usb_stop();
+	return 0;
+}
diff --git a/board/cm1_qp1/fwupdate.h b/board/cm1_qp1/fwupdate.h
new file mode 100644
index 0000000000..119c2d691c
--- /dev/null
+++ b/board/cm1_qp1/fwupdate.h
@@ -0,0 +1,47 @@
+/*
+ * (C) Copyright 2007 Schindler Lift Inc.
+ *
+ * Author: Michel Marti <mma@objectxp.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __FW_UPDATE_H
+#define __FW_UPDATE_H
+
+/* Default prefix for output messages */
+#define LOG_PREFIX	"CM1:   "
+
+/* Extra debug macro */
+#ifdef CONFIG_FWUPDATE_DEBUG
+#define FW_DEBUG(fmt...) printf(LOG_PREFIX fmt)
+#else
+#define FW_DEBUG(fmt...)
+#endif
+
+/* Name of the directory holding firmware images */
+#define FW_DIR		"nx-fw"
+#define RESCUE_IMAGE	"nxrs.img"
+#define LOAD_ADDR	0x400000
+#define RS_BOOTARGS	"ramdisk=8192K"
+
+/* Main function for fwupdate */
+void cm1_fwupdate(void);
+
+#endif /* __FW_UPDATE_H */
diff --git a/board/cm1_qp1/u-boot.lds b/board/cm1_qp1/u-boot.lds
new file mode 100644
index 0000000000..8fa9c0f7ed
--- /dev/null
+++ b/board/cm1_qp1/u-boot.lds
@@ -0,0 +1,123 @@
+/*
+ * (C) Copyright 2003-2007
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+SECTIONS
+{
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    cpu/mpc5xxx/start.o	(.text)
+    *(.text)
+    *(.fixup)
+    *(.got1)
+    . = ALIGN(16);
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+    *(.eh_frame)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x0FFF) & 0xFFFFF000;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
+  __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  . = .;
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+
+  . = .;
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(4096);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(4096);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}
diff --git a/board/esd/cpci405/cpci405.c b/board/esd/cpci405/cpci405.c
index f80361081a..69cb8cef56 100644
--- a/board/esd/cpci405/cpci405.c
+++ b/board/esd/cpci405/cpci405.c
@@ -23,13 +23,15 @@
 
 #include <common.h>
 #include <asm/processor.h>
+#include <asm/io.h>
 #include <command.h>
 #include <malloc.h>
 #include <net.h>
+#include <pci.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
-extern int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]);       /*cmd_boot.c*/
+extern int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]);	/*cmd_boot.c*/
 #if 0
 #define FPGA_DEBUG
 #endif
@@ -52,8 +54,6 @@ const unsigned char fpgadata[] =
  * include common fpga code (for esd boards)
  */
 #include "../common/fpga.c"
-
-
 #include "../common/auto_update.h"
 
 #ifdef CONFIG_CPCI405AB
@@ -86,13 +86,11 @@ au_image_t au_image[] = {
 
 int N_AU_IMAGES = (sizeof(au_image) / sizeof(au_image[0]));
 
-
 /* Prototypes */
 int cpci405_version(void);
 int gunzip(void *, int, unsigned char *, unsigned long *);
 void lxt971_no_sleep(void);
 
-
 int board_early_init_f (void)
 {
 #ifndef CONFIG_CPCI405_VER2
@@ -111,10 +109,10 @@ int board_early_init_f (void)
 	/*
 	 * First pull fpga-prg pin low, to disable fpga logic (on version 2 board)
 	 */
-	out32(GPIO0_ODR, 0x00000000);        /* no open drain pins      */
-	out32(GPIO0_TCR, CFG_FPGA_PRG);      /* setup for output        */
+	out32(GPIO0_ODR, 0x00000000);	     /* no open drain pins	*/
+	out32(GPIO0_TCR, CFG_FPGA_PRG);      /* setup for output	*/
 	out32(GPIO0_OR,  CFG_FPGA_PRG);      /* set output pins to high */
-	out32(GPIO0_OR, 0);                  /* pull prg low            */
+	out32(GPIO0_OR, 0);		     /* pull prg low		*/
 
 	/*
 	 * Boot onboard FPGA
@@ -176,47 +174,48 @@ int board_early_init_f (void)
 	 * IRQ 30 (EXT IRQ 5) PCI SLOT 3; active low; level sensitive
 	 * IRQ 31 (EXT IRQ 6) COMPACT FLASH; active high; level sensitive
 	 */
-	mtdcr(uicsr, 0xFFFFFFFF);       /* clear all ints */
-	mtdcr(uicer, 0x00000000);       /* disable all ints */
-	mtdcr(uiccr, 0x00000000);       /* set all to be non-critical*/
+	mtdcr(uicsr, 0xFFFFFFFF);	/* clear all ints */
+	mtdcr(uicer, 0x00000000);	/* disable all ints */
+	mtdcr(uiccr, 0x00000000);	/* set all to be non-critical*/
+#ifdef CONFIG_CPCI405_6U
 	if (cpci405_version() == 3) {
-		mtdcr(uicpr, 0xFFFFFF99);       /* set int polarities */
+		mtdcr(uicpr, 0xFFFFFF99);	/* set int polarities */
 	} else {
-		mtdcr(uicpr, 0xFFFFFF81);       /* set int polarities */
+		mtdcr(uicpr, 0xFFFFFF81);	/* set int polarities */
 	}
-	mtdcr(uictr, 0x10000000);       /* set int trigger levels */
-	mtdcr(uicvcr, 0x00000001);      /* set vect base=0,INT0 highest priority*/
-	mtdcr(uicsr, 0xFFFFFFFF);       /* clear all ints */
+#else
+	mtdcr(uicpr, 0xFFFFFF81);	/* set int polarities */
+#endif
+	mtdcr(uictr, 0x10000000);	/* set int trigger levels */
+	mtdcr(uicvcr, 0x00000001);	/* set vect base=0,INT0 highest priority*/
+	mtdcr(uicsr, 0xFFFFFFFF);	/* clear all ints */
 
 	return 0;
 }
 
-
 /* ------------------------------------------------------------------------- */
 
 int ctermm2(void)
 {
 #ifdef CONFIG_CPCI405_VER2
-	return 0;                       /* no, board is cpci405 */
+	return 0;			/* no, board is cpci405 */
 #else
 	if ((*(unsigned char *)0xf0000400 == 0x00) &&
 	    (*(unsigned char *)0xf0000401 == 0x01))
-		return 0;               /* no, board is cpci405 */
+		return 0;		/* no, board is cpci405 */
 	else
-		return -1;              /* yes, board is cterm-m2 */
+		return -1;		/* yes, board is cterm-m2 */
 #endif
 }
 
-
 int cpci405_host(void)
 {
 	if (mfdcr(strap) & PSR_PCI_ARBIT_EN)
-		return -1;              /* yes, board is cpci405 host */
+		return -1;		/* yes, board is cpci405 host */
 	else
-		return 0;               /* no, board is cpci405 adapter */
+		return 0;		/* no, board is cpci405 adapter */
 }
 
-
 int cpci405_version(void)
 {
 	unsigned long cntrl0Reg;
@@ -227,10 +226,10 @@ int cpci405_version(void)
 	 */
 	cntrl0Reg = mfdcr(cntrl0);
 	mtdcr(cntrl0, cntrl0Reg | 0x03000000);
-	out32(GPIO0_ODR, in32(GPIO0_ODR) & ~0x00180000);
-	out32(GPIO0_TCR, in32(GPIO0_TCR) & ~0x00180000);
-	udelay(1000);                   /* wait some time before reading input */
-	value = in32(GPIO0_IR) & 0x00180000;       /* get config bits */
+	out_be32((void*)GPIO0_ODR, in_be32((void*)GPIO0_ODR) & ~0x00180000);
+	out_be32((void*)GPIO0_TCR, in_be32((void*)GPIO0_TCR) & ~0x00180000);
+	udelay(1000);			/* wait some time before reading input */
+	value = in_be32((void*)GPIO0_IR) & 0x00180000;	     /* get config bits */
 
 	/*
 	 * Restore GPIO settings
@@ -245,7 +244,7 @@ int cpci405_version(void)
 		/* CS2==0 && CS3==1 -> version 2 */
 		return 2;
 	case 0x00100000:
-		/* CS2==1 && CS3==0 -> version 3 */
+		/* CS2==1 && CS3==0 -> version 3 or 6U board */
 		return 3;
 	case 0x00000000:
 		/* CS2==0 && CS3==0 -> version 4 */
@@ -256,13 +255,11 @@ int cpci405_version(void)
 	}
 }
 
-
 int misc_init_f (void)
 {
 	return 0;  /* dummy implementation */
 }
 
-
 int misc_init_r (void)
 {
 	unsigned long cntrl0Reg;
@@ -283,7 +280,6 @@ int misc_init_r (void)
 	 * On CPCI-405 version 2 the environment is saved in eeprom!
 	 * FPGA can be gzip compressed (malloc) and booted this late.
 	 */
-
 	if (cpci405_version() >= 2) {
 		/*
 		 * Setup GPIO pins (CS6+CS7 as GPIO)
@@ -354,6 +350,7 @@ int misc_init_r (void)
 		SET_FPGA(FPGA_PRG | FPGA_CLK | FPGA_DATA);
 		udelay(1000); /* wait 1ms */
 
+#ifdef CONFIG_CPCI405_6U
 		if (cpci405_version() == 3) {
 			volatile unsigned short *fpga_mode = (unsigned short *)CFG_FPGA_BASE_ADDR;
 			volatile unsigned char *leds = (unsigned char *)CFG_LED_ADDR;
@@ -375,6 +372,7 @@ int misc_init_r (void)
 			udelay(100);
 			*fpga_mode &= ~(CFG_FPGA_MODE_DUART_RESET);
 		}
+#endif
 	}
 	else {
 		puts("\n*** U-Boot Version does not match Board Version!\n");
@@ -425,7 +423,6 @@ int misc_init_r (void)
 	return (0);
 }
 
-
 /*
  * Check Board Identity:
  */
@@ -481,7 +478,7 @@ int checkboard (void)
 	}
 
 #ifndef CONFIG_CPCI405_VER2
-	puts ("\nFPGA:  ");
+	puts ("\nFPGA:	");
 
 	/* display infos on fpgaimage */
 	index = 15;
@@ -493,12 +490,6 @@ int checkboard (void)
 #endif
 
 	putc ('\n');
-
-	/*
-	 * Disable sleep mode in LXT971
-	 */
-	lxt971_no_sleep();
-
 	return 0;
 }
 
@@ -511,22 +502,18 @@ long int initdram (int board_type)
 	mtdcr(memcfga, mem_mb0cf);
 	val = mfdcr(memcfgd);
 
-#if 0
-	printf("\nmb0cf=%x\n", val); /* test-only */
-	printf("strap=%x\n", mfdcr(strap)); /* test-only */
-#endif
-
 	return (4*1024*1024 << ((val & 0x000e0000) >> 17));
 }
 
-/* ------------------------------------------------------------------------- */
-
-int testdram (void)
+void reset_phy(void)
 {
-	/* TODO: XXX XXX XXX */
-	printf ("test: 16 MB - ok\n");
+#ifdef CONFIG_LXT971_NO_SLEEP
 
-	return (0);
+	/*
+	 * Disable sleep mode in LXT971
+	 */
+	lxt971_no_sleep();
+#endif
 }
 
 /* ------------------------------------------------------------------------- */
@@ -551,14 +538,47 @@ void ide_set_reset(int on)
 #endif /* CONFIG_IDE_RESET */
 #endif /* CONFIG_CPCI405_VER2 */
 
+#if defined(CONFIG_PCI)
+void cpci405_pci_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
+{
+	unsigned char int_line = 0xff;
+
+	/*
+	 * Write pci interrupt line register (cpci405 specific)
+	 */
+	switch (PCI_DEV(dev) & 0x03) {
+	case 0:
+		int_line = 27 + 2;
+		break;
+	case 1:
+		int_line = 27 + 3;
+		break;
+	case 2:
+		int_line = 27 + 0;
+		break;
+	case 3:
+		int_line = 27 + 1;
+		break;
+	}
+
+	pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, int_line);
+}
+
+int pci_pre_init(struct pci_controller *hose)
+{
+	hose->fixup_irq = cpci405_pci_fixup_irq;
+	return 1;
+}
+#endif /* defined(CONFIG_PCI) */
+
 
 #ifdef CONFIG_CPCI405AB
 
-#define ONE_WIRE_CLEAR   (*(volatile unsigned short *)(CFG_FPGA_BASE_ADDR + CFG_FPGA_MODE) \
+#define ONE_WIRE_CLEAR	 (*(volatile unsigned short *)(CFG_FPGA_BASE_ADDR + CFG_FPGA_MODE) \
 			  |= CFG_FPGA_MODE_1WIRE_DIR)
-#define ONE_WIRE_SET     (*(volatile unsigned short *)(CFG_FPGA_BASE_ADDR + CFG_FPGA_MODE) \
+#define ONE_WIRE_SET	 (*(volatile unsigned short *)(CFG_FPGA_BASE_ADDR + CFG_FPGA_MODE) \
 			  &= ~CFG_FPGA_MODE_1WIRE_DIR)
-#define ONE_WIRE_GET     (*(volatile unsigned short *)(CFG_FPGA_BASE_ADDR + CFG_FPGA_STATUS) \
+#define ONE_WIRE_GET	 (*(volatile unsigned short *)(CFG_FPGA_BASE_ADDR + CFG_FPGA_STATUS) \
 			  & CFG_FPGA_MODE_1WIRE)
 
 /*
@@ -581,7 +601,6 @@ int OWTouchReset(void)
 	return result;
 }
 
-
 /*
  * Send 1 a 1-wire write bit.
  * Provide 10us recovery time.
@@ -607,7 +626,6 @@ void OWWriteBit(int bit)
 	}
 }
 
-
 /*
  * Read a bit from the 1-wire bus and return it.
  * Provide 10us recovery time.
@@ -627,7 +645,6 @@ int OWReadBit(void)
 	return result;
 }
 
-
 void OWWriteByte(int data)
 {
 	int loop;
@@ -638,7 +655,6 @@ void OWWriteByte(int data)
 	}
 }
 
-
 int OWReadByte(void)
 {
 	int loop, result = 0;
@@ -653,7 +669,6 @@ int OWReadByte(void)
 	return result;
 }
 
-
 int do_onewire(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 {
 	volatile unsigned short val;
@@ -694,7 +709,6 @@ U_BOOT_CMD(
 	NULL
 	);
 
-
 #define CFG_I2C_EEPROM_ADDR_2	0x51	/* EEPROM CAT28WC32		*/
 #define CFG_ENV_SIZE_2	0x800	/* 2048 bytes may be used for env vars*/
 
diff --git a/board/hermes/hermes.c b/board/hermes/hermes.c
index a523db1a48..8fd081fef3 100644
--- a/board/hermes/hermes.c
+++ b/board/hermes/hermes.c
@@ -597,6 +597,7 @@ void show_boot_progress (int status)
 {
 	volatile immap_t *immr = (immap_t *) CFG_IMMR;
 
+	if (status < -32) status = -1;	/* let things compatible */
 	status ^= 0x0F;
 	status = (status & 0x0F) << 14;
 	immr->im_cpm.cp_pbdat = (immr->im_cpm.cp_pbdat & ~PB_LED_ALL) | status;
diff --git a/board/logodl/logodl.c b/board/logodl/logodl.c
index 14fd28f56f..897787bcf7 100644
--- a/board/logodl/logodl.c
+++ b/board/logodl/logodl.c
@@ -107,6 +107,7 @@ void logodl_set_led(int led, int state)
 
 void show_boot_progress (int status)
 {
+	if (status < -32) status = -1;  /* let things compatible */
 	/*
 	  switch(status) {
 	  case  1: logodl_set_led(0,1); break;
diff --git a/board/lwmon5/Makefile b/board/lwmon5/Makefile
new file mode 100644
index 0000000000..06ef7f9331
--- /dev/null
+++ b/board/lwmon5/Makefile
@@ -0,0 +1,51 @@
+#
+# (C) Copyright 2002-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS	= $(BOARD).o sdram.o
+SOBJS	= init.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/lwmon5/config.mk b/board/lwmon5/config.mk
new file mode 100644
index 0000000000..bf2b8798c1
--- /dev/null
+++ b/board/lwmon5/config.mk
@@ -0,0 +1,39 @@
+#
+# (C) Copyright 2002
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+#
+# lwmon5 (440EPx)
+#
+
+ifndef TEXT_BASE
+TEXT_BASE = 0xFFF80000
+endif
+
+PLATFORM_CPPFLAGS += -DCONFIG_440=1
+
+ifeq ($(debug),1)
+PLATFORM_CPPFLAGS += -DDEBUG
+endif
+
+ifeq ($(dbcr),1)
+PLATFORM_CPPFLAGS += -DCFG_INIT_DBCR=0x8cff0000
+endif
diff --git a/board/lwmon5/init.S b/board/lwmon5/init.S
new file mode 100644
index 0000000000..6798e80985
--- /dev/null
+++ b/board/lwmon5/init.S
@@ -0,0 +1,90 @@
+/*
+ * (C) Copyright 2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ *  Copyright (C) 2002 Scott McNutt <smcnutt@artesyncp.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <ppc_asm.tmpl>
+#include <config.h>
+#include <asm-ppc/mmu.h>
+
+/**************************************************************************
+ * TLB TABLE
+ *
+ * This table is used by the cpu boot code to setup the initial tlb
+ * entries. Rather than make broad assumptions in the cpu source tree,
+ * this table lets each board set things up however they like.
+ *
+ *  Pointer to the table is returned in r1
+ *
+ *************************************************************************/
+	.section .bootpg,"ax"
+	.globl tlbtab
+
+tlbtab:
+	tlbtab_start
+
+	/*
+	 * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the
+	 * speed up boot process. It is patched after relocation to enable SA_I
+	 */
+	tlbentry(CFG_BOOT_BASE_ADDR, SZ_256M, CFG_BOOT_BASE_ADDR, 1, AC_R|AC_W|AC_X|SA_G)
+
+	/*
+	 * TLB entries for SDRAM are not needed on this platform.
+	 * They are dynamically generated in the SPD DDR(2) detection
+	 * routine.
+	 */
+
+#ifdef CFG_INIT_RAM_DCACHE
+	/* TLB-entry for init-ram in dcache (SA_I must be turned off!) */
+	tlbentry(CFG_INIT_RAM_ADDR, SZ_64K, CFG_INIT_RAM_ADDR, 0, AC_R|AC_W|AC_X|SA_G)
+#endif
+
+	/* TLB-entry for PCI Memory */
+	tlbentry(CFG_PCI_MEMBASE, SZ_256M, CFG_PCI_MEMBASE, 1, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCI_MEMBASE1, SZ_256M, CFG_PCI_MEMBASE1, 1, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCI_MEMBASE2, SZ_256M, CFG_PCI_MEMBASE2, 1, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCI_MEMBASE3, SZ_256M, CFG_PCI_MEMBASE3, 1, AC_R|AC_W|SA_G|SA_I)
+
+	/* TLB-entry for the FPGA Chip select 2 */
+	tlbentry(CFG_FPGA_BASE_0, SZ_1M, CFG_FPGA_BASE_0, 1, AC_R|AC_W|AC_X|SA_I|SA_G)
+
+	/* TLB-entry for the FPGA Chip select 3 */
+	tlbentry(CFG_FPGA_BASE_1, SZ_1M, CFG_FPGA_BASE_1, 1,AC_R|AC_W|AC_X|SA_I|SA_G)
+
+	/* TLB-entry for the LIME Controller */
+	tlbentry(CFG_LIME_BASE_0, SZ_16M, CFG_LIME_BASE_0, 1, AC_R|AC_W|AC_X|SA_I|SA_G)
+	tlbentry(CFG_LIME_BASE_1, SZ_16M, CFG_LIME_BASE_1, 1, AC_R|AC_W|AC_X|SA_I|SA_G)
+	tlbentry(CFG_LIME_BASE_2, SZ_16M, CFG_LIME_BASE_2, 1, AC_R|AC_W|AC_X|SA_I|SA_G)
+	tlbentry(CFG_LIME_BASE_3, SZ_16M, CFG_LIME_BASE_3, 1, AC_R|AC_W|AC_X|SA_I|SA_G)
+
+	/* TLB-entry for Internal Registers & OCM */
+	tlbentry(0xe0000000, SZ_16M, 0xe0000000, 0,  AC_R|AC_W|AC_X|SA_I)
+
+	/*TLB-entry PCI registers*/
+	tlbentry(0xEEC00000, SZ_1K, 0xEEC00000, 1,  AC_R|AC_W|AC_X|SA_G|SA_I)
+
+	/* TLB-entry for peripherals */
+	tlbentry(0xEF000000, SZ_16M, 0xEF000000, 1, AC_R|AC_W|AC_X|SA_G|SA_I)
+
+	tlbtab_end
diff --git a/board/lwmon5/lwmon5.c b/board/lwmon5/lwmon5.c
new file mode 100644
index 0000000000..d916284753
--- /dev/null
+++ b/board/lwmon5/lwmon5.c
@@ -0,0 +1,465 @@
+/*
+ * (C) Copyright 2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <ppc440.h>
+#include <asm/processor.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+extern flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips	*/
+
+ulong flash_get_size (ulong base, int banknum);
+
+int board_early_init_f(void)
+{
+	u32 sdr0_pfc1, sdr0_pfc2;
+	u32 reg;
+
+	/* PLB Write pipelining disabled. Denali Core workaround */
+	mtdcr(plb0_acr, 0xDE000000);
+	mtdcr(plb1_acr, 0xDE000000);
+
+	/*--------------------------------------------------------------------
+	 * Setup the interrupt controller polarities, triggers, etc.
+	 *-------------------------------------------------------------------*/
+	mtdcr(uic0sr, 0xffffffff);  /* clear all. if write with 1 then the status is cleared  */
+	mtdcr(uic0er, 0x00000000);  /* disable all */
+	mtdcr(uic0cr, 0x00000000);  /* we have not critical interrupts at the moment */
+	mtdcr(uic0pr, 0xfffff7ff);  /* Adjustment of the polarity */
+	mtdcr(uic0tr, 0x00000810);  /* per ref-board manual */
+	mtdcr(uic0vr, 0x00000000);  /* int31 highest, base=0x000 is within DDRAM */
+	mtdcr(uic0sr, 0xffffffff);  /* clear all */
+
+	mtdcr(uic1sr, 0xffffffff);  /* clear all */
+	mtdcr(uic1er, 0x00000000);  /* disable all */
+	mtdcr(uic1cr, 0x00000000);  /* all non-critical */
+	mtdcr(uic1pr, 0xFFFFC7AD);  /* Adjustment of the polarity */
+	mtdcr(uic1tr, 0x0600384A);  /* per ref-board manual */
+	mtdcr(uic1vr, 0x00000000);  /* int31 highest, base=0x000 is within DDRAM */
+	mtdcr(uic1sr, 0xffffffff);  /* clear all */
+
+	mtdcr(uic2sr, 0xffffffff);  /* clear all */
+	mtdcr(uic2er, 0x00000000);  /* disable all */
+	mtdcr(uic2cr, 0x00000000);  /* all non-critical */
+	mtdcr(uic2pr, 0x27C00000);  /* Adjustment of the polarity */
+	mtdcr(uic2tr, 0xDFC00000);  /* per ref-board manual */
+	mtdcr(uic2vr, 0x00000000);  /* int31 highest, base=0x000 is within DDRAM */
+	mtdcr(uic2sr, 0xffffffff);  /* clear all. Why this??? */
+
+	/* Trace Pins are disabled. SDR0_PFC0 Register */
+	mtsdr(SDR0_PFC0, 0x0);
+
+	/* select Ethernet pins */
+	mfsdr(SDR0_PFC1, sdr0_pfc1);
+	/* SMII via ZMII */
+	sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_SELECT_MASK) |
+		SDR0_PFC1_SELECT_CONFIG_6;
+	mfsdr(SDR0_PFC2, sdr0_pfc2);
+	sdr0_pfc2 = (sdr0_pfc2 & ~SDR0_PFC2_SELECT_MASK) |
+		SDR0_PFC2_SELECT_CONFIG_6;
+
+	/* enable SPI (SCP) */
+	sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_SIS_MASK) | SDR0_PFC1_SIS_SCP_SEL;
+
+	mtsdr(SDR0_PFC2, sdr0_pfc2);
+	mtsdr(SDR0_PFC1, sdr0_pfc1);
+
+	mtsdr(SDR0_PFC4, 0x80000000);
+
+	/* PCI arbiter disabled */
+	/* PCI Host Configuration disbaled */
+	mfsdr(sdr_pci0, reg);
+	reg = 0;
+	mtsdr(sdr_pci0, 0x00000000 | reg);
+
+	gpio_write_bit(CFG_GPIO_FLASH_WP, 1);
+
+	return 0;
+}
+
+/*---------------------------------------------------------------------------+
+  | misc_init_r.
+  +---------------------------------------------------------------------------*/
+int misc_init_r(void)
+{
+	u32 pbcr;
+	int size_val = 0;
+	u32 reg;
+	unsigned long usb2d0cr = 0;
+	unsigned long usb2phy0cr, usb2h0cr = 0;
+	unsigned long sdr0_pfc1;
+
+	/*
+	 * FLASH stuff...
+	 */
+
+	/* Re-do sizing to get full correct info */
+
+	/* adjust flash start and offset */
+	gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
+	gd->bd->bi_flashoffset = 0;
+
+	mfebc(pb0cr, pbcr);
+	switch (gd->bd->bi_flashsize) {
+	case 1 << 20:
+		size_val = 0;
+		break;
+	case 2 << 20:
+		size_val = 1;
+		break;
+	case 4 << 20:
+		size_val = 2;
+		break;
+	case 8 << 20:
+		size_val = 3;
+		break;
+	case 16 << 20:
+		size_val = 4;
+		break;
+	case 32 << 20:
+		size_val = 5;
+		break;
+	case 64 << 20:
+		size_val = 6;
+		break;
+	case 128 << 20:
+		size_val = 7;
+		break;
+	}
+	pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
+	mtebc(pb0cr, pbcr);
+
+	/*
+	 * Re-check to get correct base address
+	 */
+	flash_get_size(gd->bd->bi_flashstart, 0);
+
+	/* Monitor protection ON by default */
+	(void)flash_protect(FLAG_PROTECT_SET,
+			    -CFG_MONITOR_LEN,
+			    0xffffffff,
+			    &flash_info[0]);
+
+	/* Env protection ON by default */
+	(void)flash_protect(FLAG_PROTECT_SET,
+			    CFG_ENV_ADDR_REDUND,
+			    CFG_ENV_ADDR_REDUND + 2*CFG_ENV_SECT_SIZE - 1,
+			    &flash_info[0]);
+
+	/*
+	 * USB suff...
+	 */
+	/* SDR Setting */
+	mfsdr(SDR0_PFC1, sdr0_pfc1);
+	mfsdr(SDR0_USB0, usb2d0cr);
+	mfsdr(SDR0_USB2PHY0CR, usb2phy0cr);
+	mfsdr(SDR0_USB2H0CR, usb2h0cr);
+
+	usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_XOCLK_MASK;
+	usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL;	/*0*/
+	usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_WDINT_MASK;
+	usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_WDINT_16BIT_30MHZ;	/*1*/
+	usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DVBUS_MASK;
+	usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PURDIS;		/*0*/
+	usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DWNSTR_MASK;
+	usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_HOST;		/*1*/
+	usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_UTMICN_MASK;
+	usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_HOST;		/*1*/
+
+	/* An 8-bit/60MHz interface is the only possible alternative
+	   when connecting the Device to the PHY */
+	usb2h0cr   = usb2h0cr &~SDR0_USB2H0CR_WDINT_MASK;
+	usb2h0cr   = usb2h0cr | SDR0_USB2H0CR_WDINT_16BIT_30MHZ;	/*1*/
+
+	mtsdr(SDR0_PFC1, sdr0_pfc1);
+	mtsdr(SDR0_USB0, usb2d0cr);
+	mtsdr(SDR0_USB2PHY0CR, usb2phy0cr);
+	mtsdr(SDR0_USB2H0CR, usb2h0cr);
+
+	/*
+	 * Clear resets
+	 */
+	udelay (1000);
+	mtsdr(SDR0_SRST1, 0x00000000);
+	udelay (1000);
+	mtsdr(SDR0_SRST0, 0x00000000);
+
+	printf("USB:   Host(int phy) Device(ext phy)\n");
+
+	/*
+	 * Clear PLB4A0_ACR[WRP]
+	 * This fix will make the MAL burst disabling patch for the Linux
+	 * EMAC driver obsolete.
+	 */
+	reg = mfdcr(plb4_acr) & ~PLB4_ACR_WRP;
+	mtdcr(plb4_acr, reg);
+
+	/*
+	 * Reset Lime controller
+	 */
+	gpio_write_bit(CFG_GPIO_LIME_S, 1);
+	udelay(500);
+	gpio_write_bit(CFG_GPIO_LIME_RST, 1);
+
+	/* Lime memory clock adjusted to 133MHz */
+	out_be32((void *)CFG_LIME_SDRAM_CLOCK, CFG_LIME_CLOCK_133MHZ);
+	/* Wait untill time expired. Because of requirements in lime manual */
+	udelay(300);
+	/* Write lime controller memory parameters */
+	out_be32((void *)CFG_LIME_MMR, CFG_LIME_MMR_VALUE);
+
+	/*
+	 * Reset PHY's
+	 */
+	gpio_write_bit(CFG_GPIO_PHY0_RST, 0);
+	gpio_write_bit(CFG_GPIO_PHY1_RST, 0);
+	udelay(100);
+	gpio_write_bit(CFG_GPIO_PHY0_RST, 1);
+	gpio_write_bit(CFG_GPIO_PHY1_RST, 1);
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	char *s = getenv("serial#");
+
+	printf("Board: lwmon5");
+
+	if (s != NULL) {
+		puts(", serial# ");
+		puts(s);
+	}
+	putc('\n');
+
+	return (0);
+}
+
+#if defined(CFG_DRAM_TEST)
+int testdram(void)
+{
+	unsigned long *mem = (unsigned long *)0;
+	const unsigned long kend = (1024 / sizeof(unsigned long));
+	unsigned long k, n;
+
+	mtmsr(0);
+
+	for (k = 0; k < CFG_MBYTES_SDRAM;
+	     ++k, mem += (1024 / sizeof(unsigned long))) {
+		if ((k & 1023) == 0) {
+			printf("%3d MB\r", k / 1024);
+		}
+
+		memset(mem, 0xaaaaaaaa, 1024);
+		for (n = 0; n < kend; ++n) {
+			if (mem[n] != 0xaaaaaaaa) {
+				printf("SDRAM test fails at: %08x\n",
+				       (uint) & mem[n]);
+				return 1;
+			}
+		}
+
+		memset(mem, 0x55555555, 1024);
+		for (n = 0; n < kend; ++n) {
+			if (mem[n] != 0x55555555) {
+				printf("SDRAM test fails at: %08x\n",
+				       (uint) & mem[n]);
+				return 1;
+			}
+		}
+	}
+	printf("SDRAM test passes\n");
+	return 0;
+}
+#endif
+
+/*************************************************************************
+ *  pci_pre_init
+ *
+ *  This routine is called just prior to registering the hose and gives
+ *  the board the opportunity to check things. Returning a value of zero
+ *  indicates that things are bad & PCI initialization should be aborted.
+ *
+ *	Different boards may wish to customize the pci controller structure
+ *	(add regions, override default access routines, etc) or perform
+ *	certain pre-initialization actions.
+ *
+ ************************************************************************/
+#if defined(CONFIG_PCI)
+int pci_pre_init(struct pci_controller *hose)
+{
+	unsigned long addr;
+
+	/*-------------------------------------------------------------------------+
+	  | Set priority for all PLB3 devices to 0.
+	  | Set PLB3 arbiter to fair mode.
+	  +-------------------------------------------------------------------------*/
+	mfsdr(sdr_amp1, addr);
+	mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
+	addr = mfdcr(plb3_acr);
+	mtdcr(plb3_acr, addr | 0x80000000);
+
+	/*-------------------------------------------------------------------------+
+	  | Set priority for all PLB4 devices to 0.
+	  +-------------------------------------------------------------------------*/
+	mfsdr(sdr_amp0, addr);
+	mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
+	addr = mfdcr(plb4_acr) | 0xa0000000;	/* Was 0x8---- */
+	mtdcr(plb4_acr, addr);
+
+	/*-------------------------------------------------------------------------+
+	  | Set Nebula PLB4 arbiter to fair mode.
+	  +-------------------------------------------------------------------------*/
+	/* Segment0 */
+	addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
+	addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
+	addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
+	addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
+	mtdcr(plb0_acr, addr);
+
+	/* Segment1 */
+	addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
+	addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
+	addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
+	addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
+	mtdcr(plb1_acr, addr);
+
+	return 1;
+}
+#endif	/* defined(CONFIG_PCI) */
+
+/*************************************************************************
+ *  pci_target_init
+ *
+ *	The bootstrap configuration provides default settings for the pci
+ *	inbound map (PIM). But the bootstrap config choices are limited and
+ *	may not be sufficient for a given board.
+ *
+ ************************************************************************/
+#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT)
+void pci_target_init(struct pci_controller *hose)
+{
+	/*--------------------------------------------------------------------------+
+	 * Set up Direct MMIO registers
+	 *--------------------------------------------------------------------------*/
+	/*--------------------------------------------------------------------------+
+	  | PowerPC440EPX PCI Master configuration.
+	  | Map one 1Gig range of PLB/processor addresses to PCI memory space.
+	  |   PLB address 0xA0000000-0xDFFFFFFF ==> PCI address 0xA0000000-0xDFFFFFFF
+	  |   Use byte reversed out routines to handle endianess.
+	  | Make this region non-prefetchable.
+	  +--------------------------------------------------------------------------*/
+	out32r(PCIX0_PMM0MA, 0x00000000);	/* PMM0 Mask/Attribute - disabled b4 setting */
+	out32r(PCIX0_PMM0LA, CFG_PCI_MEMBASE);	/* PMM0 Local Address */
+	out32r(PCIX0_PMM0PCILA, CFG_PCI_MEMBASE);	/* PMM0 PCI Low Address */
+	out32r(PCIX0_PMM0PCIHA, 0x00000000);	/* PMM0 PCI High Address */
+	out32r(PCIX0_PMM0MA, 0xE0000001);	/* 512M + No prefetching, and enable region */
+
+	out32r(PCIX0_PMM1MA, 0x00000000);	/* PMM0 Mask/Attribute - disabled b4 setting */
+	out32r(PCIX0_PMM1LA, CFG_PCI_MEMBASE2); /* PMM0 Local Address */
+	out32r(PCIX0_PMM1PCILA, CFG_PCI_MEMBASE2);	/* PMM0 PCI Low Address */
+	out32r(PCIX0_PMM1PCIHA, 0x00000000);	/* PMM0 PCI High Address */
+	out32r(PCIX0_PMM1MA, 0xE0000001);	/* 512M + No prefetching, and enable region */
+
+	out32r(PCIX0_PTM1MS, 0x00000001);	/* Memory Size/Attribute */
+	out32r(PCIX0_PTM1LA, 0);	/* Local Addr. Reg */
+	out32r(PCIX0_PTM2MS, 0);	/* Memory Size/Attribute */
+	out32r(PCIX0_PTM2LA, 0);	/* Local Addr. Reg */
+
+	/*--------------------------------------------------------------------------+
+	 * Set up Configuration registers
+	 *--------------------------------------------------------------------------*/
+
+	/* Program the board's subsystem id/vendor id */
+	pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
+			      CFG_PCI_SUBSYS_VENDORID);
+	pci_write_config_word(0, PCI_SUBSYSTEM_ID, CFG_PCI_SUBSYS_ID);
+
+	/* Configure command register as bus master */
+	pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
+
+	/* 240nS PCI clock */
+	pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
+
+	/* No error reporting */
+	pci_write_config_word(0, PCI_ERREN, 0);
+
+	pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
+
+}
+#endif				/* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */
+
+/*************************************************************************
+ *  pci_master_init
+ *
+ ************************************************************************/
+#if defined(CONFIG_PCI) && defined(CFG_PCI_MASTER_INIT)
+void pci_master_init(struct pci_controller *hose)
+{
+	unsigned short temp_short;
+
+	/*--------------------------------------------------------------------------+
+	  | Write the PowerPC440 EP PCI Configuration regs.
+	  |   Enable PowerPC440 EP to be a master on the PCI bus (PMM).
+	  |   Enable PowerPC440 EP to act as a PCI memory target (PTM).
+	  +--------------------------------------------------------------------------*/
+	pci_read_config_word(0, PCI_COMMAND, &temp_short);
+	pci_write_config_word(0, PCI_COMMAND,
+			      temp_short | PCI_COMMAND_MASTER |
+			      PCI_COMMAND_MEMORY);
+}
+#endif				/* defined(CONFIG_PCI) && defined(CFG_PCI_MASTER_INIT) */
+
+/*************************************************************************
+ *  is_pci_host
+ *
+ *	This routine is called to determine if a pci scan should be
+ *	performed. With various hardware environments (especially cPCI and
+ *	PPMC) it's insufficient to depend on the state of the arbiter enable
+ *	bit in the strap register, or generic host/adapter assumptions.
+ *
+ *	Rather than hard-code a bad assumption in the general 440 code, the
+ *	440 pci code requires the board to decide at runtime.
+ *
+ *	Return 0 for adapter mode, non-zero for host (monarch) mode.
+ *
+ *
+ ************************************************************************/
+#if defined(CONFIG_PCI)
+int is_pci_host(struct pci_controller *hose)
+{
+	/* Cactus is always configured as host. */
+	return (1);
+}
+#endif				/* defined(CONFIG_PCI) */
+
+void hw_watchdog_reset(void)
+{
+	int val;
+
+	/*
+	 * Toggle watchdog output
+	 */
+	val = gpio_read_out_bit(CFG_GPIO_WATCHDOG) == 0 ? 1 : 0;
+	gpio_write_bit(CFG_GPIO_WATCHDOG, val);
+}
diff --git a/board/lwmon5/sdram.c b/board/lwmon5/sdram.c
new file mode 100644
index 0000000000..9a4a8eea8f
--- /dev/null
+++ b/board/lwmon5/sdram.c
@@ -0,0 +1,662 @@
+/*
+ * (C) Copyright 2006
+ * Sylvie Gohl,		    AMCC/IBM, gohl.sylvie@fr.ibm.com
+ * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com
+ * Thierry Roman,	    AMCC/IBM, thierry_roman@fr.ibm.com
+ * Alain Saurel,	    AMCC/IBM, alain.saurel@fr.ibm.com
+ * Robert Snyder,	    AMCC/IBM, rob.snyder@fr.ibm.com
+ *
+ * (C) Copyright 2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/* define DEBUG for debugging output (obviously ;-)) */
+#if 0
+#define DEBUG
+#endif
+
+#include <common.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+#include <asm/io.h>
+#include <ppc440.h>
+
+#include "sdram.h"
+
+/*
+ * This DDR2 setup code can dynamically setup the TLB entries for the DDR2 memory
+ * region. Right now the cache should still be disabled in U-Boot because of the
+ * EMAC driver, that need it's buffer descriptor to be located in non cached
+ * memory.
+ *
+ * If at some time this restriction doesn't apply anymore, just define
+ * CFG_ENABLE_SDRAM_CACHE in the board config file and this code should setup
+ * everything correctly.
+ */
+#ifdef CFG_ENABLE_SDRAM_CACHE
+#define MY_TLB_WORD2_I_ENABLE	0			/* enable caching on SDRAM */
+#else
+#define MY_TLB_WORD2_I_ENABLE	TLB_WORD2_I_ENABLE	/* disable caching on SDRAM */
+#endif
+
+void program_tlb(u32 phys_addr, u32 virt_addr, u32 size, u32 tlb_word2_i_value);
+void dcbz_area(u32 start_address, u32 num_bytes);
+void dflush(void);
+
+#ifdef CONFIG_ADD_RAM_INFO
+static u32 is_ecc_enabled(void)
+{
+	u32 val;
+
+	mfsdram(DDR0_22, val);
+	val &= DDR0_22_CTRL_RAW_MASK;
+	if (val)
+		return 1;
+	else
+		return 0;
+}
+
+void board_add_ram_info(int use_default)
+{
+	PPC440_SYS_INFO board_cfg;
+	u32 val;
+
+	if (is_ecc_enabled())
+		puts(" (ECC");
+	else
+		puts(" (ECC not");
+
+	get_sys_info(&board_cfg);
+	printf(" enabled, %d MHz", (board_cfg.freqPLB * 2) / 1000000);
+
+	mfsdram(DDR0_03, val);
+	val = DDR0_03_CASLAT_DECODE(val);
+	printf(", CL%d)", val);
+}
+#endif
+
+static int wait_for_dlllock(void)
+{
+	u32 val;
+	int wait = 0;
+
+	/*
+	 * Wait for the DCC master delay line to finish calibration
+	 */
+	mtdcr(ddrcfga, DDR0_17);
+	val = DDR0_17_DLLLOCKREG_UNLOCKED;
+
+	while (wait != 0xffff) {
+		val = mfdcr(ddrcfgd);
+		if ((val & DDR0_17_DLLLOCKREG_MASK) == DDR0_17_DLLLOCKREG_LOCKED)
+			/* dlllockreg bit on */
+			return 0;
+		else
+			wait++;
+	}
+	debug("0x%04x: DDR0_17 Value (dlllockreg bit): 0x%08x\n", wait, val);
+	debug("Waiting for dlllockreg bit to raise\n");
+
+	return -1;
+}
+
+#if defined(CONFIG_DDR_DATA_EYE)
+int wait_for_dram_init_complete(void)
+{
+	u32 val;
+	int wait = 0;
+
+	/*
+	 * Wait for 'DRAM initialization complete' bit in status register
+	 */
+	mtdcr(ddrcfga, DDR0_00);
+
+	while (wait != 0xffff) {
+		val = mfdcr(ddrcfgd);
+		if ((val & DDR0_00_INT_STATUS_BIT6) == DDR0_00_INT_STATUS_BIT6)
+			/* 'DRAM initialization complete' bit */
+			return 0;
+		else
+			wait++;
+	}
+
+	debug("DRAM initialization complete bit in status register did not rise\n");
+
+	return -1;
+}
+
+#define NUM_TRIES 64
+#define NUM_READS 10
+
+void denali_core_search_data_eye(u32 start_addr, u32 memory_size)
+{
+	int k, j;
+	u32 val;
+	u32 wr_dqs_shift, dqs_out_shift, dll_dqs_delay_X;
+	u32 max_passing_cases = 0, wr_dqs_shift_with_max_passing_cases = 0;
+	u32 passing_cases = 0, dll_dqs_delay_X_sw_val = 0;
+	u32 dll_dqs_delay_X_start_window = 0, dll_dqs_delay_X_end_window = 0;
+	volatile u32 *ram_pointer;
+	u32 test[NUM_TRIES] = {
+		0x00000000, 0x00000000, 0xFFFFFFFF, 0xFFFFFFFF,
+		0x00000000, 0x00000000, 0xFFFFFFFF, 0xFFFFFFFF,
+		0xFFFFFFFF, 0xFFFFFFFF, 0x00000000, 0x00000000,
+		0xFFFFFFFF, 0xFFFFFFFF, 0x00000000, 0x00000000,
+		0xAAAAAAAA, 0xAAAAAAAA, 0x55555555, 0x55555555,
+		0xAAAAAAAA, 0xAAAAAAAA, 0x55555555, 0x55555555,
+		0x55555555, 0x55555555, 0xAAAAAAAA, 0xAAAAAAAA,
+		0x55555555, 0x55555555, 0xAAAAAAAA, 0xAAAAAAAA,
+		0xA5A5A5A5, 0xA5A5A5A5, 0x5A5A5A5A, 0x5A5A5A5A,
+		0xA5A5A5A5, 0xA5A5A5A5, 0x5A5A5A5A, 0x5A5A5A5A,
+		0x5A5A5A5A, 0x5A5A5A5A, 0xA5A5A5A5, 0xA5A5A5A5,
+		0x5A5A5A5A, 0x5A5A5A5A, 0xA5A5A5A5, 0xA5A5A5A5,
+		0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA,
+		0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA,
+		0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55,
+		0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55 };
+
+	ram_pointer = (volatile u32 *)start_addr;
+
+	for (wr_dqs_shift = 64; wr_dqs_shift < 96; wr_dqs_shift++) {
+		/*for (wr_dqs_shift=1; wr_dqs_shift<96; wr_dqs_shift++) {*/
+
+		/*
+		 * De-assert 'start' parameter.
+		 */
+		mtdcr(ddrcfga, DDR0_02);
+		val = (mfdcr(ddrcfgd) & ~DDR0_02_START_MASK) | DDR0_02_START_OFF;
+		mtdcr(ddrcfgd, val);
+
+		/*
+		 * Set 'wr_dqs_shift'
+		 */
+		mtdcr(ddrcfga, DDR0_09);
+		val = (mfdcr(ddrcfgd) & ~DDR0_09_WR_DQS_SHIFT_MASK)
+			| DDR0_09_WR_DQS_SHIFT_ENCODE(wr_dqs_shift);
+		mtdcr(ddrcfgd, val);
+
+		/*
+		 * Set 'dqs_out_shift' = wr_dqs_shift + 32
+		 */
+		dqs_out_shift = wr_dqs_shift + 32;
+		mtdcr(ddrcfga, DDR0_22);
+		val = (mfdcr(ddrcfgd) & ~DDR0_22_DQS_OUT_SHIFT_MASK)
+			| DDR0_22_DQS_OUT_SHIFT_ENCODE(dqs_out_shift);
+		mtdcr(ddrcfgd, val);
+
+		passing_cases = 0;
+
+		for (dll_dqs_delay_X = 1; dll_dqs_delay_X < 64; dll_dqs_delay_X++) {
+			/*for (dll_dqs_delay_X=1; dll_dqs_delay_X<128; dll_dqs_delay_X++) {*/
+			/*
+			 * Set 'dll_dqs_delay_X'.
+			 */
+			/* dll_dqs_delay_0 */
+			mtdcr(ddrcfga, DDR0_17);
+			val = (mfdcr(ddrcfgd) & ~DDR0_17_DLL_DQS_DELAY_0_MASK)
+				| DDR0_17_DLL_DQS_DELAY_0_ENCODE(dll_dqs_delay_X);
+			mtdcr(ddrcfgd, val);
+			/* dll_dqs_delay_1 to dll_dqs_delay_4 */
+			mtdcr(ddrcfga, DDR0_18);
+			val = (mfdcr(ddrcfgd) & ~DDR0_18_DLL_DQS_DELAY_X_MASK)
+				| DDR0_18_DLL_DQS_DELAY_4_ENCODE(dll_dqs_delay_X)
+				| DDR0_18_DLL_DQS_DELAY_3_ENCODE(dll_dqs_delay_X)
+				| DDR0_18_DLL_DQS_DELAY_2_ENCODE(dll_dqs_delay_X)
+				| DDR0_18_DLL_DQS_DELAY_1_ENCODE(dll_dqs_delay_X);
+			mtdcr(ddrcfgd, val);
+			/* dll_dqs_delay_5 to dll_dqs_delay_8 */
+			mtdcr(ddrcfga, DDR0_19);
+			val = (mfdcr(ddrcfgd) & ~DDR0_19_DLL_DQS_DELAY_X_MASK)
+				| DDR0_19_DLL_DQS_DELAY_8_ENCODE(dll_dqs_delay_X)
+				| DDR0_19_DLL_DQS_DELAY_7_ENCODE(dll_dqs_delay_X)
+				| DDR0_19_DLL_DQS_DELAY_6_ENCODE(dll_dqs_delay_X)
+				| DDR0_19_DLL_DQS_DELAY_5_ENCODE(dll_dqs_delay_X);
+			mtdcr(ddrcfgd, val);
+
+			ppcMsync();
+			ppcMbar();
+
+			/*
+			 * Assert 'start' parameter.
+			 */
+			mtdcr(ddrcfga, DDR0_02);
+			val = (mfdcr(ddrcfgd) & ~DDR0_02_START_MASK) | DDR0_02_START_ON;
+			mtdcr(ddrcfgd, val);
+
+			ppcMsync();
+			ppcMbar();
+
+			/*
+			 * Wait for the DCC master delay line to finish calibration
+			 */
+			if (wait_for_dlllock() != 0) {
+				printf("dlllock did not occur !!!\n");
+				printf("denali_core_search_data_eye!!!\n");
+				printf("wr_dqs_shift = %d - dll_dqs_delay_X = %d\n",
+				       wr_dqs_shift, dll_dqs_delay_X);
+				hang();
+			}
+			ppcMsync();
+			ppcMbar();
+
+			if (wait_for_dram_init_complete() != 0) {
+				printf("dram init complete did not occur !!!\n");
+				printf("denali_core_search_data_eye!!!\n");
+				printf("wr_dqs_shift = %d - dll_dqs_delay_X = %d\n",
+				       wr_dqs_shift, dll_dqs_delay_X);
+				hang();
+			}
+			udelay(100);  /* wait 100us to ensure init is really completed !!! */
+
+			/* write values */
+			for (j=0; j<NUM_TRIES; j++) {
+				ram_pointer[j] = test[j];
+
+				/* clear any cache at ram location */
+				__asm__("dcbf 0,%0": :"r" (&ram_pointer[j]));
+			}
+
+			/* read values back */
+			for (j=0; j<NUM_TRIES; j++) {
+				for (k=0; k<NUM_READS; k++) {
+					/* clear any cache at ram location */
+					__asm__("dcbf 0,%0": :"r" (&ram_pointer[j]));
+
+					if (ram_pointer[j] != test[j])
+						break;
+				}
+
+				/* read error */
+				if (k != NUM_READS)
+					break;
+			}
+
+			/* See if the dll_dqs_delay_X value passed.*/
+			if (j < NUM_TRIES) {
+				/* Failed */
+				passing_cases = 0;
+				/* break; */
+			} else {
+				/* Passed */
+				if (passing_cases == 0)
+					dll_dqs_delay_X_sw_val = dll_dqs_delay_X;
+				passing_cases++;
+				if (passing_cases >= max_passing_cases) {
+					max_passing_cases = passing_cases;
+					wr_dqs_shift_with_max_passing_cases = wr_dqs_shift;
+					dll_dqs_delay_X_start_window = dll_dqs_delay_X_sw_val;
+					dll_dqs_delay_X_end_window = dll_dqs_delay_X;
+				}
+			}
+
+			/*
+			 * De-assert 'start' parameter.
+			 */
+			mtdcr(ddrcfga, DDR0_02);
+			val = (mfdcr(ddrcfgd) & ~DDR0_02_START_MASK) | DDR0_02_START_OFF;
+			mtdcr(ddrcfgd, val);
+
+		} /* for (dll_dqs_delay_X=0; dll_dqs_delay_X<128; dll_dqs_delay_X++) */
+
+	} /* for (wr_dqs_shift=0; wr_dqs_shift<96; wr_dqs_shift++) */
+
+	/*
+	 * Largest passing window is now detected.
+	 */
+
+	/* Compute dll_dqs_delay_X value */
+	dll_dqs_delay_X = (dll_dqs_delay_X_end_window + dll_dqs_delay_X_start_window) / 2;
+	wr_dqs_shift = wr_dqs_shift_with_max_passing_cases;
+
+	debug("DQS calibration - Window detected:\n");
+	debug("max_passing_cases = %d\n", max_passing_cases);
+	debug("wr_dqs_shift	 = %d\n", wr_dqs_shift);
+	debug("dll_dqs_delay_X	 = %d\n", dll_dqs_delay_X);
+	debug("dll_dqs_delay_X window = %d - %d\n",
+	      dll_dqs_delay_X_start_window, dll_dqs_delay_X_end_window);
+
+	/*
+	 * De-assert 'start' parameter.
+	 */
+	mtdcr(ddrcfga, DDR0_02);
+	val = (mfdcr(ddrcfgd) & ~DDR0_02_START_MASK) | DDR0_02_START_OFF;
+	mtdcr(ddrcfgd, val);
+
+	/*
+	 * Set 'wr_dqs_shift'
+	 */
+	mtdcr(ddrcfga, DDR0_09);
+	val = (mfdcr(ddrcfgd) & ~DDR0_09_WR_DQS_SHIFT_MASK)
+		| DDR0_09_WR_DQS_SHIFT_ENCODE(wr_dqs_shift);
+	mtdcr(ddrcfgd, val);
+	debug("DDR0_09=0x%08lx\n", val);
+
+	/*
+	 * Set 'dqs_out_shift' = wr_dqs_shift + 32
+	 */
+	dqs_out_shift = wr_dqs_shift + 32;
+	mtdcr(ddrcfga, DDR0_22);
+	val = (mfdcr(ddrcfgd) & ~DDR0_22_DQS_OUT_SHIFT_MASK)
+		| DDR0_22_DQS_OUT_SHIFT_ENCODE(dqs_out_shift);
+	mtdcr(ddrcfgd, val);
+	debug("DDR0_22=0x%08lx\n", val);
+
+	/*
+	 * Set 'dll_dqs_delay_X'.
+	 */
+	/* dll_dqs_delay_0 */
+	mtdcr(ddrcfga, DDR0_17);
+	val = (mfdcr(ddrcfgd) & ~DDR0_17_DLL_DQS_DELAY_0_MASK)
+		| DDR0_17_DLL_DQS_DELAY_0_ENCODE(dll_dqs_delay_X);
+	mtdcr(ddrcfgd, val);
+	debug("DDR0_17=0x%08lx\n", val);
+
+	/* dll_dqs_delay_1 to dll_dqs_delay_4 */
+	mtdcr(ddrcfga, DDR0_18);
+	val = (mfdcr(ddrcfgd) & ~DDR0_18_DLL_DQS_DELAY_X_MASK)
+		| DDR0_18_DLL_DQS_DELAY_4_ENCODE(dll_dqs_delay_X)
+		| DDR0_18_DLL_DQS_DELAY_3_ENCODE(dll_dqs_delay_X)
+		| DDR0_18_DLL_DQS_DELAY_2_ENCODE(dll_dqs_delay_X)
+		| DDR0_18_DLL_DQS_DELAY_1_ENCODE(dll_dqs_delay_X);
+	mtdcr(ddrcfgd, val);
+	debug("DDR0_18=0x%08lx\n", val);
+
+	/* dll_dqs_delay_5 to dll_dqs_delay_8 */
+	mtdcr(ddrcfga, DDR0_19);
+	val = (mfdcr(ddrcfgd) & ~DDR0_19_DLL_DQS_DELAY_X_MASK)
+		| DDR0_19_DLL_DQS_DELAY_8_ENCODE(dll_dqs_delay_X)
+		| DDR0_19_DLL_DQS_DELAY_7_ENCODE(dll_dqs_delay_X)
+		| DDR0_19_DLL_DQS_DELAY_6_ENCODE(dll_dqs_delay_X)
+		| DDR0_19_DLL_DQS_DELAY_5_ENCODE(dll_dqs_delay_X);
+	mtdcr(ddrcfgd, val);
+	debug("DDR0_19=0x%08lx\n", val);
+
+	/*
+	 * Assert 'start' parameter.
+	 */
+	mtdcr(ddrcfga, DDR0_02);
+	val = (mfdcr(ddrcfgd) & ~DDR0_02_START_MASK) | DDR0_02_START_ON;
+	mtdcr(ddrcfgd, val);
+
+	ppcMsync();
+	ppcMbar();
+
+	/*
+	 * Wait for the DCC master delay line to finish calibration
+	 */
+	if (wait_for_dlllock() != 0) {
+		printf("dlllock did not occur !!!\n");
+		hang();
+	}
+	ppcMsync();
+	ppcMbar();
+
+	if (wait_for_dram_init_complete() != 0) {
+		printf("dram init complete did not occur !!!\n");
+		hang();
+	}
+	udelay(100);  /* wait 100us to ensure init is really completed !!! */
+}
+#endif /* CONFIG_DDR_DATA_EYE */
+
+#ifdef CONFIG_DDR_ECC
+static void wait_ddr_idle(void)
+{
+	/*
+	 * Controller idle status cannot be determined for Denali
+	 * DDR2 code. Just return here.
+	 */
+}
+
+static void blank_string(int size)
+{
+	int i;
+
+	for (i=0; i<size; i++)
+		putc('\b');
+	for (i=0; i<size; i++)
+		putc(' ');
+	for (i=0; i<size; i++)
+		putc('\b');
+}
+
+static void program_ecc(u32 start_address,
+			u32 num_bytes,
+			u32 tlb_word2_i_value)
+{
+	u32 current_address;
+	u32 end_address;
+	u32 address_increment;
+	u32 val;
+	char str[] = "ECC generation -";
+	char slash[] = "\\|/-\\|/-";
+	int loop = 0;
+	int loopi = 0;
+
+	current_address = start_address;
+
+	sync();
+	eieio();
+	wait_ddr_idle();
+
+	if (tlb_word2_i_value == TLB_WORD2_I_ENABLE) {
+		/* ECC bit set method for non-cached memory */
+		address_increment = 4;
+		end_address = current_address + num_bytes;
+
+		puts(str);
+
+		while (current_address < end_address) {
+			*((u32 *)current_address) = 0x00000000;
+			current_address += address_increment;
+
+			if ((loop++ % (2 << 20)) == 0) {
+				putc('\b');
+				putc(slash[loopi++ % 8]);
+			}
+		}
+
+		blank_string(strlen(str));
+	} else {
+		/* ECC bit set method for cached memory */
+#if 1 /* test-only: will remove this define later, when ECC problems are solved! */
+		/*
+		 * Some boards (like lwmon5) need to preserve the memory
+		 * content upon ECC generation (for the log-buffer).
+		 * Therefore we don't fill the memory with a pattern or
+		 * just zero it, but write the same values back that are
+		 * already in the memory cells.
+		 */
+		address_increment = CFG_CACHELINE_SIZE;
+		end_address = current_address + num_bytes;
+
+		current_address = start_address;
+		while (current_address < end_address) {
+			ppcDcbi(current_address);
+			ppcDcbf(current_address);
+			current_address += CFG_CACHELINE_SIZE;
+		}
+#else
+		dcbz_area(start_address, num_bytes);
+		dflush();
+#endif
+	}
+
+	sync();
+	eieio();
+	wait_ddr_idle();
+
+	/* Clear error status */
+	mfsdram(DDR0_00, val);
+	mtsdram(DDR0_00, val | DDR0_00_INT_ACK_ALL);
+
+	/* Set 'int_mask' parameter to functionnal value */
+	mfsdram(DDR0_01, val);
+	mtsdram(DDR0_01, ((val &~ DDR0_01_INT_MASK_MASK) | DDR0_01_INT_MASK_ALL_OFF));
+
+	sync();
+	eieio();
+	wait_ddr_idle();
+}
+#endif
+
+static __inline__ u32 get_mcsr(void)
+{
+	u32 val;
+
+	asm volatile("mfspr %0, 0x23c" : "=r" (val) :);
+	return val;
+}
+
+static __inline__ void set_mcsr(u32 val)
+{
+	asm volatile("mtspr 0x23c, %0" : "=r" (val) :);
+}
+
+/*************************************************************************
+ *
+ * initdram -- 440EPx's DDR controller is a DENALI Core
+ *
+ ************************************************************************/
+long int initdram (int board_type)
+{
+	u32 val;
+
+#if 0 /* test-only: will remove this define later, when ECC problems are solved! */
+	/* CL=3 */
+	mtsdram(DDR0_02, 0x00000000);
+
+	mtsdram(DDR0_00, 0x0000190A);
+	mtsdram(DDR0_01, 0x01000000);
+	mtsdram(DDR0_03, 0x02030603); /* A suitable burst length was taken. CAS is right for our board */
+
+	mtsdram(DDR0_04, 0x0A030300);
+	mtsdram(DDR0_05, 0x02020308);
+	mtsdram(DDR0_06, 0x0103C812);
+	mtsdram(DDR0_07, 0x00090100);
+	mtsdram(DDR0_08, 0x02c80001);
+	mtsdram(DDR0_09, 0x00011D5F);
+	mtsdram(DDR0_10, 0x00000300);
+	mtsdram(DDR0_11, 0x000CC800);
+	mtsdram(DDR0_12, 0x00000003);
+	mtsdram(DDR0_14, 0x00000000);
+	mtsdram(DDR0_17, 0x1e000000);
+	mtsdram(DDR0_18, 0x1e1e1e1e);
+	mtsdram(DDR0_19, 0x1e1e1e1e);
+	mtsdram(DDR0_20, 0x0B0B0B0B);
+	mtsdram(DDR0_21, 0x0B0B0B0B);
+#ifdef CONFIG_DDR_ECC
+	mtsdram(DDR0_22, 0x00267F0B | DDR0_22_CTRL_RAW_ECC_ENABLE); /* enable ECC	*/
+#else
+	mtsdram(DDR0_22, 0x00267F0B);
+#endif
+
+	mtsdram(DDR0_23, 0x01000000);
+	mtsdram(DDR0_24, 0x01010001);
+
+	mtsdram(DDR0_26, 0x2D93028A);
+	mtsdram(DDR0_27, 0x0784682B);
+
+	mtsdram(DDR0_28, 0x00000080);
+	mtsdram(DDR0_31, 0x00000000);
+	mtsdram(DDR0_42, 0x01000006);
+
+	mtsdram(DDR0_43, 0x030A0200);
+	mtsdram(DDR0_44, 0x00000003);
+	mtsdram(DDR0_02, 0x00000001); /* Activate the denali core */
+#else
+	/* CL=4 */
+	mtsdram(DDR0_02, 0x00000000);
+
+	mtsdram(DDR0_00, 0x0000190A);
+	mtsdram(DDR0_01, 0x01000000);
+	mtsdram(DDR0_03, 0x02040803); /* A suitable burst length was taken. CAS is right for our board */
+
+	mtsdram(DDR0_04, 0x0B030300);
+	mtsdram(DDR0_05, 0x02020308);
+	mtsdram(DDR0_06, 0x0003C812);
+	mtsdram(DDR0_07, 0x00090100);
+	mtsdram(DDR0_08, 0x03c80001);
+	mtsdram(DDR0_09, 0x00011D5F);
+	mtsdram(DDR0_10, 0x00000300);
+	mtsdram(DDR0_11, 0x000CC800);
+	mtsdram(DDR0_12, 0x00000003);
+	mtsdram(DDR0_14, 0x00000000);
+	mtsdram(DDR0_17, 0x1e000000);
+	mtsdram(DDR0_18, 0x1e1e1e1e);
+	mtsdram(DDR0_19, 0x1e1e1e1e);
+	mtsdram(DDR0_20, 0x0B0B0B0B);
+	mtsdram(DDR0_21, 0x0B0B0B0B);
+#ifdef CONFIG_DDR_ECC
+	mtsdram(DDR0_22, 0x00267F0B | DDR0_22_CTRL_RAW_ECC_ENABLE); /* enable ECC       */
+#else
+	mtsdram(DDR0_22, 0x00267F0B);
+#endif
+
+	mtsdram(DDR0_23, 0x01000000);
+	mtsdram(DDR0_24, 0x01010001);
+
+	mtsdram(DDR0_26, 0x2D93028A);
+	mtsdram(DDR0_27, 0x0784682B);
+
+	mtsdram(DDR0_28, 0x00000080);
+	mtsdram(DDR0_31, 0x00000000);
+	mtsdram(DDR0_42, 0x01000008);
+
+	mtsdram(DDR0_43, 0x050A0200);
+	mtsdram(DDR0_44, 0x00000005);
+	mtsdram(DDR0_02, 0x00000001); /* Activate the denali core */
+#endif
+
+	wait_for_dlllock();
+
+	/*
+	 * Program tlb entries for this size (dynamic)
+	 */
+	program_tlb(0, 0, CFG_MBYTES_SDRAM << 20, MY_TLB_WORD2_I_ENABLE);
+
+	/*
+	 * Setup 2nd TLB with same physical address but different virtual address
+	 * with cache enabled. This is done for fast ECC generation.
+	 */
+	program_tlb(0, CFG_DDR_CACHED_ADDR, CFG_MBYTES_SDRAM << 20, 0);
+
+#ifdef CONFIG_DDR_DATA_EYE
+	/*
+	 * Perform data eye search if requested.
+	 */
+	denali_core_search_data_eye(CFG_DDR_CACHED_ADDR, CFG_MBYTES_SDRAM << 20);
+
+	/*
+	 * Clear possible errors resulting from data-eye-search.
+	 * If not done, then we could get an interrupt later on when
+	 * exceptions are enabled.
+	 */
+	val = get_mcsr();
+	set_mcsr(val);
+#endif
+
+#ifdef CONFIG_DDR_ECC
+	/*
+	 * If ECC is enabled, initialize the parity bits.
+	 */
+	program_ecc(CFG_DDR_CACHED_ADDR, CFG_MBYTES_SDRAM << 20, 0);
+#endif
+
+	return (CFG_MBYTES_SDRAM << 20);
+}
diff --git a/board/lwmon5/sdram.h b/board/lwmon5/sdram.h
new file mode 100644
index 0000000000..7f847aa2ad
--- /dev/null
+++ b/board/lwmon5/sdram.h
@@ -0,0 +1,505 @@
+/*
+ * (C) Copyright 2006
+ * Sylvie Gohl,             AMCC/IBM, gohl.sylvie@fr.ibm.com
+ * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com
+ * Thierry Roman,           AMCC/IBM, thierry_roman@fr.ibm.com
+ * Alain Saurel,            AMCC/IBM, alain.saurel@fr.ibm.com
+ * Robert Snyder,           AMCC/IBM, rob.snyder@fr.ibm.com
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _SPD_SDRAM_DENALI_H_
+#define _SPD_SDRAM_DENALI_H_
+
+#define ppcMsync	sync
+#define ppcMbar		eieio
+
+/* General definitions */
+#define MAX_SPD_BYTE        128         /* highest SPD byte # to read */
+#define DENALI_REG_NUMBER   45          /* 45 Regs in PPC440EPx Denali Core */
+#define SUPPORTED_DIMMS_NB  7           /* Number of supported DIMM modules types */
+#define SDRAM_NONE          0           /* No DIMM detected in Slot */
+#define MAXRANKS            2           /* 2 ranks maximum */
+
+/* Supported PLB Frequencies */
+#define PLB_FREQ_133MHZ     133333333
+#define PLB_FREQ_152MHZ     152000000
+#define PLB_FREQ_160MHZ     160000000
+#define PLB_FREQ_166MHZ     166666666
+
+/* Denali Core Registers */
+#define SDRAM_DCR_BASE 0x10
+
+#define DDR_DCR_BASE 0x10
+#define ddrcfga  (DDR_DCR_BASE+0x0)   /* DDR configuration address reg */
+#define ddrcfgd  (DDR_DCR_BASE+0x1)   /* DDR configuration data reg    */
+
+/*-----------------------------------------------------------------------------+
+  | Values for ddrcfga register - indirect addressing of these regs
+  +-----------------------------------------------------------------------------*/
+
+#define DDR0_00                         0x00
+#define DDR0_00_INT_ACK_MASK              0x7F000000 /* Write only */
+#define DDR0_00_INT_ACK_ALL               0x7F000000
+#define DDR0_00_INT_ACK_ENCODE(n)           ((((unsigned long)(n))&0x7F)<<24)
+#define DDR0_00_INT_ACK_DECODE(n)           ((((unsigned long)(n))>>24)&0x7F)
+/* Status */
+#define DDR0_00_INT_STATUS_MASK           0x00FF0000 /* Read only */
+/* Bit0. A single access outside the defined PHYSICAL memory space detected. */
+#define DDR0_00_INT_STATUS_BIT0           0x00010000
+/* Bit1. Multiple accesses outside the defined PHYSICAL memory space detected. */
+#define DDR0_00_INT_STATUS_BIT1           0x00020000
+/* Bit2. Single correctable ECC event detected */
+#define DDR0_00_INT_STATUS_BIT2           0x00040000
+/* Bit3. Multiple correctable ECC events detected. */
+#define DDR0_00_INT_STATUS_BIT3           0x00080000
+/* Bit4. Single uncorrectable ECC event detected. */
+#define DDR0_00_INT_STATUS_BIT4           0x00100000
+/* Bit5. Multiple uncorrectable ECC events detected. */
+#define DDR0_00_INT_STATUS_BIT5           0x00200000
+/* Bit6. DRAM initialization complete. */
+#define DDR0_00_INT_STATUS_BIT6           0x00400000
+/* Bit7. Logical OR of all lower bits. */
+#define DDR0_00_INT_STATUS_BIT7           0x00800000
+
+#define DDR0_00_INT_STATUS_ENCODE(n)        ((((unsigned long)(n))&0xFF)<<16)
+#define DDR0_00_INT_STATUS_DECODE(n)        ((((unsigned long)(n))>>16)&0xFF)
+#define DDR0_00_DLL_INCREMENT_MASK        0x00007F00
+#define DDR0_00_DLL_INCREMENT_ENCODE(n)     ((((unsigned long)(n))&0x7F)<<8)
+#define DDR0_00_DLL_INCREMENT_DECODE(n)     ((((unsigned long)(n))>>8)&0x7F)
+#define DDR0_00_DLL_START_POINT_MASK      0x0000007F
+#define DDR0_00_DLL_START_POINT_ENCODE(n)   ((((unsigned long)(n))&0x7F)<<0)
+#define DDR0_00_DLL_START_POINT_DECODE(n)   ((((unsigned long)(n))>>0)&0x7F)
+
+
+#define DDR0_01                         0x01
+#define DDR0_01_PLB0_DB_CS_LOWER_MASK     0x1F000000
+#define DDR0_01_PLB0_DB_CS_LOWER_ENCODE(n)  ((((unsigned long)(n))&0x1F)<<24)
+#define DDR0_01_PLB0_DB_CS_LOWER_DECODE(n)  ((((unsigned long)(n))>>24)&0x1F)
+#define DDR0_01_PLB0_DB_CS_UPPER_MASK     0x001F0000
+#define DDR0_01_PLB0_DB_CS_UPPER_ENCODE(n)  ((((unsigned long)(n))&0x1F)<<16)
+#define DDR0_01_PLB0_DB_CS_UPPER_DECODE(n)  ((((unsigned long)(n))>>16)&0x1F)
+#define DDR0_01_OUT_OF_RANGE_TYPE_MASK    0x00000700 /* Read only */
+#define DDR0_01_OUT_OF_RANGE_TYPE_ENCODE(n)               ((((unsigned long)(n))&0x7)<<8)
+#define DDR0_01_OUT_OF_RANGE_TYPE_DECODE(n)               ((((unsigned long)(n))>>8)&0x7)
+#define DDR0_01_INT_MASK_MASK             0x000000FF
+#define DDR0_01_INT_MASK_ENCODE(n)          ((((unsigned long)(n))&0xFF)<<0)
+#define DDR0_01_INT_MASK_DECODE(n)          ((((unsigned long)(n))>>0)&0xFF)
+#define DDR0_01_INT_MASK_ALL_ON           0x000000FF
+#define DDR0_01_INT_MASK_ALL_OFF          0x00000000
+
+#define DDR0_02                         0x02
+#define DDR0_02_MAX_CS_REG_MASK           0x02000000 /* Read only */
+#define DDR0_02_MAX_CS_REG_ENCODE(n)        ((((unsigned long)(n))&0x2)<<24)
+#define DDR0_02_MAX_CS_REG_DECODE(n)        ((((unsigned long)(n))>>24)&0x2)
+#define DDR0_02_MAX_COL_REG_MASK          0x000F0000 /* Read only */
+#define DDR0_02_MAX_COL_REG_ENCODE(n)       ((((unsigned long)(n))&0xF)<<16)
+#define DDR0_02_MAX_COL_REG_DECODE(n)       ((((unsigned long)(n))>>16)&0xF)
+#define DDR0_02_MAX_ROW_REG_MASK          0x00000F00 /* Read only */
+#define DDR0_02_MAX_ROW_REG_ENCODE(n)       ((((unsigned long)(n))&0xF)<<8)
+#define DDR0_02_MAX_ROW_REG_DECODE(n)       ((((unsigned long)(n))>>8)&0xF)
+#define DDR0_02_START_MASK                0x00000001
+#define DDR0_02_START_ENCODE(n)             ((((unsigned long)(n))&0x1)<<0)
+#define DDR0_02_START_DECODE(n)             ((((unsigned long)(n))>>0)&0x1)
+#define DDR0_02_START_OFF                 0x00000000
+#define DDR0_02_START_ON                  0x00000001
+
+#define DDR0_03                         0x03
+#define DDR0_03_BSTLEN_MASK               0x07000000
+#define DDR0_03_BSTLEN_ENCODE(n)            ((((unsigned long)(n))&0x7)<<24)
+#define DDR0_03_BSTLEN_DECODE(n)            ((((unsigned long)(n))>>24)&0x7)
+#define DDR0_03_CASLAT_MASK               0x00070000
+#define DDR0_03_CASLAT_ENCODE(n)            ((((unsigned long)(n))&0x7)<<16)
+#define DDR0_03_CASLAT_DECODE(n)            ((((unsigned long)(n))>>16)&0x7)
+#define DDR0_03_CASLAT_LIN_MASK           0x00000F00
+#define DDR0_03_CASLAT_LIN_ENCODE(n)        ((((unsigned long)(n))&0xF)<<8)
+#define DDR0_03_CASLAT_LIN_DECODE(n)        ((((unsigned long)(n))>>8)&0xF)
+#define DDR0_03_INITAREF_MASK             0x0000000F
+#define DDR0_03_INITAREF_ENCODE(n)          ((((unsigned long)(n))&0xF)<<0)
+#define DDR0_03_INITAREF_DECODE(n)          ((((unsigned long)(n))>>0)&0xF)
+
+#define DDR0_04                         0x04
+#define DDR0_04_TRC_MASK                  0x1F000000
+#define DDR0_04_TRC_ENCODE(n)               ((((unsigned long)(n))&0x1F)<<24)
+#define DDR0_04_TRC_DECODE(n)               ((((unsigned long)(n))>>24)&0x1F)
+#define DDR0_04_TRRD_MASK                 0x00070000
+#define DDR0_04_TRRD_ENCODE(n)              ((((unsigned long)(n))&0x7)<<16)
+#define DDR0_04_TRRD_DECODE(n)              ((((unsigned long)(n))>>16)&0x7)
+#define DDR0_04_TRTP_MASK                 0x00000700
+#define DDR0_04_TRTP_ENCODE(n)              ((((unsigned long)(n))&0x7)<<8)
+#define DDR0_04_TRTP_DECODE(n)              ((((unsigned long)(n))>>8)&0x7)
+
+#define DDR0_05                         0x05
+#define DDR0_05_TMRD_MASK                 0x1F000000
+#define DDR0_05_TMRD_ENCODE(n)              ((((unsigned long)(n))&0x1F)<<24)
+#define DDR0_05_TMRD_DECODE(n)              ((((unsigned long)(n))>>24)&0x1F)
+#define DDR0_05_TEMRS_MASK                0x00070000
+#define DDR0_05_TEMRS_ENCODE(n)             ((((unsigned long)(n))&0x7)<<16)
+#define DDR0_05_TEMRS_DECODE(n)             ((((unsigned long)(n))>>16)&0x7)
+#define DDR0_05_TRP_MASK                  0x00000F00
+#define DDR0_05_TRP_ENCODE(n)               ((((unsigned long)(n))&0xF)<<8)
+#define DDR0_05_TRP_DECODE(n)               ((((unsigned long)(n))>>8)&0xF)
+#define DDR0_05_TRAS_MIN_MASK             0x000000FF
+#define DDR0_05_TRAS_MIN_ENCODE(n)          ((((unsigned long)(n))&0xFF)<<0)
+#define DDR0_05_TRAS_MIN_DECODE(n)          ((((unsigned long)(n))>>0)&0xFF)
+
+#define DDR0_06                         0x06
+#define DDR0_06_WRITEINTERP_MASK          0x01000000
+#define DDR0_06_WRITEINTERP_ENCODE(n)       ((((unsigned long)(n))&0x1)<<24)
+#define DDR0_06_WRITEINTERP_DECODE(n)       ((((unsigned long)(n))>>24)&0x1)
+#define DDR0_06_TWTR_MASK                 0x00070000
+#define DDR0_06_TWTR_ENCODE(n)              ((((unsigned long)(n))&0x7)<<16)
+#define DDR0_06_TWTR_DECODE(n)              ((((unsigned long)(n))>>16)&0x7)
+#define DDR0_06_TDLL_MASK                 0x0000FF00
+#define DDR0_06_TDLL_ENCODE(n)              ((((unsigned long)(n))&0xFF)<<8)
+#define DDR0_06_TDLL_DECODE(n)              ((((unsigned long)(n))>>8)&0xFF)
+#define DDR0_06_TRFC_MASK                 0x0000007F
+#define DDR0_06_TRFC_ENCODE(n)              ((((unsigned long)(n))&0x7F)<<0)
+#define DDR0_06_TRFC_DECODE(n)              ((((unsigned long)(n))>>0)&0x7F)
+
+#define DDR0_07                         0x07
+#define DDR0_07_NO_CMD_INIT_MASK          0x01000000
+#define DDR0_07_NO_CMD_INIT_ENCODE(n)       ((((unsigned long)(n))&0x1)<<24)
+#define DDR0_07_NO_CMD_INIT_DECODE(n)       ((((unsigned long)(n))>>24)&0x1)
+#define DDR0_07_TFAW_MASK                 0x001F0000
+#define DDR0_07_TFAW_ENCODE(n)              ((((unsigned long)(n))&0x1F)<<16)
+#define DDR0_07_TFAW_DECODE(n)              ((((unsigned long)(n))>>16)&0x1F)
+#define DDR0_07_AUTO_REFRESH_MODE_MASK    0x00000100
+#define DDR0_07_AUTO_REFRESH_MODE_ENCODE(n) ((((unsigned long)(n))&0x1)<<8)
+#define DDR0_07_AUTO_REFRESH_MODE_DECODE(n) ((((unsigned long)(n))>>8)&0x1)
+#define DDR0_07_AREFRESH_MASK             0x00000001
+#define DDR0_07_AREFRESH_ENCODE(n)          ((((unsigned long)(n))&0x1)<<0)
+#define DDR0_07_AREFRESH_DECODE(n)          ((((unsigned long)(n))>>0)&0x1)
+
+#define DDR0_08                         0x08
+#define DDR0_08_WRLAT_MASK                0x07000000
+#define DDR0_08_WRLAT_ENCODE(n)             ((((unsigned long)(n))&0x7)<<24)
+#define DDR0_08_WRLAT_DECODE(n)             ((((unsigned long)(n))>>24)&0x7)
+#define DDR0_08_TCPD_MASK                 0x00FF0000
+#define DDR0_08_TCPD_ENCODE(n)              ((((unsigned long)(n))&0xFF)<<16)
+#define DDR0_08_TCPD_DECODE(n)              ((((unsigned long)(n))>>16)&0xFF)
+#define DDR0_08_DQS_N_EN_MASK             0x00000100
+#define DDR0_08_DQS_N_EN_ENCODE(n)          ((((unsigned long)(n))&0x1)<<8)
+#define DDR0_08_DQS_N_EN_DECODE(n)          ((((unsigned long)(n))>>8)&0x1)
+#define DDR0_08_DDRII_SDRAM_MODE_MASK     0x00000001
+#define DDR0_08_DDRII_ENCODE(n)             ((((unsigned long)(n))&0x1)<<0)
+#define DDR0_08_DDRII_DECODE(n)             ((((unsigned long)(n))>>0)&0x1)
+
+#define DDR0_09                         0x09
+#define DDR0_09_OCD_ADJUST_PDN_CS_0_MASK  0x1F000000
+#define DDR0_09_OCD_ADJUST_PDN_CS_0_ENCODE(n) ((((unsigned long)(n))&0x1F)<<24)
+#define DDR0_09_OCD_ADJUST_PDN_CS_0_DECODE(n) ((((unsigned long)(n))>>24)&0x1F)
+#define DDR0_09_RTT_0_MASK                0x00030000
+#define DDR0_09_RTT_0_ENCODE(n)             ((((unsigned long)(n))&0x3)<<16)
+#define DDR0_09_RTT_0_DECODE(n)             ((((unsigned long)(n))>>16)&0x3)
+#define DDR0_09_WR_DQS_SHIFT_BYPASS_MASK  0x00007F00
+#define DDR0_09_WR_DQS_SHIFT_BYPASS_ENCODE(n) ((((unsigned long)(n))&0x7F)<<8)
+#define DDR0_09_WR_DQS_SHIFT_BYPASS_DECODE(n) ((((unsigned long)(n))>>8)&0x7F)
+#define DDR0_09_WR_DQS_SHIFT_MASK         0x0000007F
+#define DDR0_09_WR_DQS_SHIFT_ENCODE(n)      ((((unsigned long)(n))&0x7F)<<0)
+#define DDR0_09_WR_DQS_SHIFT_DECODE(n)      ((((unsigned long)(n))>>0)&0x7F)
+
+#define DDR0_10                         0x0A
+#define DDR0_10_WRITE_MODEREG_MASK        0x00010000 /* Write only */
+#define DDR0_10_WRITE_MODEREG_ENCODE(n)     ((((unsigned long)(n))&0x1)<<16)
+#define DDR0_10_WRITE_MODEREG_DECODE(n)     ((((unsigned long)(n))>>16)&0x1)
+#define DDR0_10_CS_MAP_MASK               0x00000300
+#define DDR0_10_CS_MAP_NO_MEM             0x00000000
+#define DDR0_10_CS_MAP_RANK0_INSTALLED    0x00000100
+#define DDR0_10_CS_MAP_RANK1_INSTALLED    0x00000200
+#define DDR0_10_CS_MAP_ENCODE(n)            ((((unsigned long)(n))&0x3)<<8)
+#define DDR0_10_CS_MAP_DECODE(n)            ((((unsigned long)(n))>>8)&0x3)
+#define DDR0_10_OCD_ADJUST_PUP_CS_0_MASK  0x0000001F
+#define DDR0_10_OCD_ADJUST_PUP_CS_0_ENCODE(n) ((((unsigned long)(n))&0x1F)<<0)
+#define DDR0_10_OCD_ADJUST_PUP_CS_0_DECODE(n) ((((unsigned long)(n))>>0)&0x1F)
+
+#define DDR0_11                         0x0B
+#define DDR0_11_SREFRESH_MASK             0x01000000
+#define DDR0_11_SREFRESH_ENCODE(n)          ((((unsigned long)(n))&0x1)<<24)
+#define DDR0_11_SREFRESH_DECODE(n)          ((((unsigned long)(n))>>24)&0x1F)
+#define DDR0_11_TXSNR_MASK                0x00FF0000
+#define DDR0_11_TXSNR_ENCODE(n)             ((((unsigned long)(n))&0xFF)<<16)
+#define DDR0_11_TXSNR_DECODE(n)             ((((unsigned long)(n))>>16)&0xFF)
+#define DDR0_11_TXSR_MASK                 0x0000FF00
+#define DDR0_11_TXSR_ENCODE(n)              ((((unsigned long)(n))&0xFF)<<8)
+#define DDR0_11_TXSR_DECODE(n)              ((((unsigned long)(n))>>8)&0xFF)
+
+#define DDR0_12                         0x0C
+#define DDR0_12_TCKE_MASK                 0x0000007
+#define DDR0_12_TCKE_ENCODE(n)              ((((unsigned long)(n))&0x7)<<0)
+#define DDR0_12_TCKE_DECODE(n)              ((((unsigned long)(n))>>0)&0x7)
+
+#define DDR0_13                         0x0D
+
+#define DDR0_14                         0x0E
+#define DDR0_14_DLL_BYPASS_MODE_MASK      0x01000000
+#define DDR0_14_DLL_BYPASS_MODE_ENCODE(n)   ((((unsigned long)(n))&0x1)<<24)
+#define DDR0_14_DLL_BYPASS_MODE_DECODE(n)   ((((unsigned long)(n))>>24)&0x1)
+#define DDR0_14_REDUC_MASK                0x00010000
+#define DDR0_14_REDUC_64BITS              0x00000000
+#define DDR0_14_REDUC_32BITS              0x00010000
+#define DDR0_14_REDUC_ENCODE(n)             ((((unsigned long)(n))&0x1)<<16)
+#define DDR0_14_REDUC_DECODE(n)             ((((unsigned long)(n))>>16)&0x1)
+#define DDR0_14_REG_DIMM_ENABLE_MASK      0x00000100
+#define DDR0_14_REG_DIMM_ENABLE_ENCODE(n)   ((((unsigned long)(n))&0x1)<<8)
+#define DDR0_14_REG_DIMM_ENABLE_DECODE(n)   ((((unsigned long)(n))>>8)&0x1)
+
+#define DDR0_15                         0x0F
+
+#define DDR0_16                         0x10
+
+#define DDR0_17                         0x11
+#define DDR0_17_DLL_DQS_DELAY_0_MASK      0x7F000000
+#define DDR0_17_DLL_DQS_DELAY_0_ENCODE(n)   ((((unsigned long)(n))&0x7F)<<24)
+#define DDR0_17_DLL_DQS_DELAY_0_DECODE(n)   ((((unsigned long)(n))>>24)&0x7F)
+#define DDR0_17_DLLLOCKREG_MASK           0x00010000 /* Read only */
+#define DDR0_17_DLLLOCKREG_LOCKED         0x00010000
+#define DDR0_17_DLLLOCKREG_UNLOCKED       0x00000000
+#define DDR0_17_DLLLOCKREG_ENCODE(n)        ((((unsigned long)(n))&0x1)<<16)
+#define DDR0_17_DLLLOCKREG_DECODE(n)        ((((unsigned long)(n))>>16)&0x1)
+#define DDR0_17_DLL_LOCK_MASK             0x00007F00 /* Read only */
+#define DDR0_17_DLL_LOCK_ENCODE(n)          ((((unsigned long)(n))&0x7F)<<8)
+#define DDR0_17_DLL_LOCK_DECODE(n)          ((((unsigned long)(n))>>8)&0x7F)
+
+#define DDR0_18                         0x12
+#define DDR0_18_DLL_DQS_DELAY_X_MASK      0x7F7F7F7F
+#define DDR0_18_DLL_DQS_DELAY_4_MASK      0x7F000000
+#define DDR0_18_DLL_DQS_DELAY_4_ENCODE(n)   ((((unsigned long)(n))&0x7F)<<24)
+#define DDR0_18_DLL_DQS_DELAY_4_DECODE(n)   ((((unsigned long)(n))>>24)&0x7F)
+#define DDR0_18_DLL_DQS_DELAY_3_MASK      0x007F0000
+#define DDR0_18_DLL_DQS_DELAY_3_ENCODE(n)   ((((unsigned long)(n))&0x7F)<<16)
+#define DDR0_18_DLL_DQS_DELAY_3_DECODE(n)   ((((unsigned long)(n))>>16)&0x7F)
+#define DDR0_18_DLL_DQS_DELAY_2_MASK      0x00007F00
+#define DDR0_18_DLL_DQS_DELAY_2_ENCODE(n)   ((((unsigned long)(n))&0x7F)<<8)
+#define DDR0_18_DLL_DQS_DELAY_2_DECODE(n)   ((((unsigned long)(n))>>8)&0x7F)
+#define DDR0_18_DLL_DQS_DELAY_1_MASK      0x0000007F
+#define DDR0_18_DLL_DQS_DELAY_1_ENCODE(n)   ((((unsigned long)(n))&0x7F)<<0)
+#define DDR0_18_DLL_DQS_DELAY_1_DECODE(n)   ((((unsigned long)(n))>>0)&0x7F)
+
+#define DDR0_19                         0x13
+#define DDR0_19_DLL_DQS_DELAY_X_MASK      0x7F7F7F7F
+#define DDR0_19_DLL_DQS_DELAY_8_MASK      0x7F000000
+#define DDR0_19_DLL_DQS_DELAY_8_ENCODE(n)   ((((unsigned long)(n))&0x7F)<<24)
+#define DDR0_19_DLL_DQS_DELAY_8_DECODE(n)   ((((unsigned long)(n))>>24)&0x7F)
+#define DDR0_19_DLL_DQS_DELAY_7_MASK      0x007F0000
+#define DDR0_19_DLL_DQS_DELAY_7_ENCODE(n)   ((((unsigned long)(n))&0x7F)<<16)
+#define DDR0_19_DLL_DQS_DELAY_7_DECODE(n)   ((((unsigned long)(n))>>16)&0x7F)
+#define DDR0_19_DLL_DQS_DELAY_6_MASK      0x00007F00
+#define DDR0_19_DLL_DQS_DELAY_6_ENCODE(n)   ((((unsigned long)(n))&0x7F)<<8)
+#define DDR0_19_DLL_DQS_DELAY_6_DECODE(n)   ((((unsigned long)(n))>>8)&0x7F)
+#define DDR0_19_DLL_DQS_DELAY_5_MASK      0x0000007F
+#define DDR0_19_DLL_DQS_DELAY_5_ENCODE(n)   ((((unsigned long)(n))&0x7F)<<0)
+#define DDR0_19_DLL_DQS_DELAY_5_DECODE(n)   ((((unsigned long)(n))>>0)&0x7F)
+
+#define DDR0_20                         0x14
+#define DDR0_20_DLL_DQS_BYPASS_3_MASK      0x7F000000
+#define DDR0_20_DLL_DQS_BYPASS_3_ENCODE(n)   ((((unsigned long)(n))&0x7F)<<24)
+#define DDR0_20_DLL_DQS_BYPASS_3_DECODE(n)   ((((unsigned long)(n))>>24)&0x7F)
+#define DDR0_20_DLL_DQS_BYPASS_2_MASK      0x007F0000
+#define DDR0_20_DLL_DQS_BYPASS_2_ENCODE(n)   ((((unsigned long)(n))&0x7F)<<16)
+#define DDR0_20_DLL_DQS_BYPASS_2_DECODE(n)   ((((unsigned long)(n))>>16)&0x7F)
+#define DDR0_20_DLL_DQS_BYPASS_1_MASK      0x00007F00
+#define DDR0_20_DLL_DQS_BYPASS_1_ENCODE(n)   ((((unsigned long)(n))&0x7F)<<8)
+#define DDR0_20_DLL_DQS_BYPASS_1_DECODE(n)   ((((unsigned long)(n))>>8)&0x7F)
+#define DDR0_20_DLL_DQS_BYPASS_0_MASK      0x0000007F
+#define DDR0_20_DLL_DQS_BYPASS_0_ENCODE(n)   ((((unsigned long)(n))&0x7F)<<0)
+#define DDR0_20_DLL_DQS_BYPASS_0_DECODE(n)   ((((unsigned long)(n))>>0)&0x7F)
+
+#define DDR0_21                         0x15
+#define DDR0_21_DLL_DQS_BYPASS_7_MASK      0x7F000000
+#define DDR0_21_DLL_DQS_BYPASS_7_ENCODE(n)   ((((unsigned long)(n))&0x7F)<<24)
+#define DDR0_21_DLL_DQS_BYPASS_7_DECODE(n)   ((((unsigned long)(n))>>24)&0x7F)
+#define DDR0_21_DLL_DQS_BYPASS_6_MASK      0x007F0000
+#define DDR0_21_DLL_DQS_BYPASS_6_ENCODE(n)   ((((unsigned long)(n))&0x7F)<<16)
+#define DDR0_21_DLL_DQS_BYPASS_6_DECODE(n)   ((((unsigned long)(n))>>16)&0x7F)
+#define DDR0_21_DLL_DQS_BYPASS_5_MASK      0x00007F00
+#define DDR0_21_DLL_DQS_BYPASS_5_ENCODE(n)   ((((unsigned long)(n))&0x7F)<<8)
+#define DDR0_21_DLL_DQS_BYPASS_5_DECODE(n)   ((((unsigned long)(n))>>8)&0x7F)
+#define DDR0_21_DLL_DQS_BYPASS_4_MASK      0x0000007F
+#define DDR0_21_DLL_DQS_BYPASS_4_ENCODE(n)   ((((unsigned long)(n))&0x7F)<<0)
+#define DDR0_21_DLL_DQS_BYPASS_4_DECODE(n)   ((((unsigned long)(n))>>0)&0x7F)
+
+#define DDR0_22                         0x16
+/* ECC */
+#define DDR0_22_CTRL_RAW_MASK             0x03000000
+#define DDR0_22_CTRL_RAW_ECC_DISABLE      0x00000000 /* ECC not being used */
+#define DDR0_22_CTRL_RAW_ECC_CHECK_ONLY   0x01000000 /* ECC checking is on, but no attempts to correct*/
+#define DDR0_22_CTRL_RAW_NO_ECC_RAM       0x02000000 /* No ECC RAM storage available */
+#define DDR0_22_CTRL_RAW_ECC_ENABLE       0x03000000 /* ECC checking and correcting on */
+#define DDR0_22_CTRL_RAW_ENCODE(n)          ((((unsigned long)(n))&0x3)<<24)
+#define DDR0_22_CTRL_RAW_DECODE(n)          ((((unsigned long)(n))>>24)&0x3)
+
+#define DDR0_22_DQS_OUT_SHIFT_BYPASS_MASK 0x007F0000
+#define DDR0_22_DQS_OUT_SHIFT_BYPASS_ENCODE(n) ((((unsigned long)(n))&0x7F)<<16)
+#define DDR0_22_DQS_OUT_SHIFT_BYPASS_DECODE(n) ((((unsigned long)(n))>>16)&0x7F)
+#define DDR0_22_DQS_OUT_SHIFT_MASK        0x00007F00
+#define DDR0_22_DQS_OUT_SHIFT_ENCODE(n)     ((((unsigned long)(n))&0x7F)<<8)
+#define DDR0_22_DQS_OUT_SHIFT_DECODE(n)     ((((unsigned long)(n))>>8)&0x7F)
+#define DDR0_22_DLL_DQS_BYPASS_8_MASK     0x0000007F
+#define DDR0_22_DLL_DQS_BYPASS_8_ENCODE(n)  ((((unsigned long)(n))&0x7F)<<0)
+#define DDR0_22_DLL_DQS_BYPASS_8_DECODE(n)  ((((unsigned long)(n))>>0)&0x7F)
+
+
+#define DDR0_23                         0x17
+#define DDR0_23_ODT_RD_MAP_CS0_MASK       0x03000000
+#define DDR0_23_ODT_RD_MAP_CS0_ENCODE(n)   ((((unsigned long)(n))&0x3)<<24)
+#define DDR0_23_ODT_RD_MAP_CS0_DECODE(n)   ((((unsigned long)(n))>>24)&0x3)
+#define DDR0_23_ECC_C_SYND_MASK           0x00FF0000 /* Read only */
+#define DDR0_23_ECC_C_SYND_ENCODE(n)        ((((unsigned long)(n))&0xFF)<<16)
+#define DDR0_23_ECC_C_SYND_DECODE(n)        ((((unsigned long)(n))>>16)&0xFF)
+#define DDR0_23_ECC_U_SYND_MASK           0x0000FF00 /* Read only */
+#define DDR0_23_ECC_U_SYND_ENCODE(n)        ((((unsigned long)(n))&0xFF)<<8)
+#define DDR0_23_ECC_U_SYND_DECODE(n)        ((((unsigned long)(n))>>8)&0xFF)
+#define DDR0_23_FWC_MASK                  0x00000001 /* Write only */
+#define DDR0_23_FWC_ENCODE(n)               ((((unsigned long)(n))&0x1)<<0)
+#define DDR0_23_FWC_DECODE(n)               ((((unsigned long)(n))>>0)&0x1)
+
+#define DDR0_24                         0x18
+#define DDR0_24_RTT_PAD_TERMINATION_MASK  0x03000000
+#define DDR0_24_RTT_PAD_TERMINATION_ENCODE(n) ((((unsigned long)(n))&0x3)<<24)
+#define DDR0_24_RTT_PAD_TERMINATION_DECODE(n) ((((unsigned long)(n))>>24)&0x3)
+#define DDR0_24_ODT_WR_MAP_CS1_MASK       0x00030000
+#define DDR0_24_ODT_WR_MAP_CS1_ENCODE(n)    ((((unsigned long)(n))&0x3)<<16)
+#define DDR0_24_ODT_WR_MAP_CS1_DECODE(n)    ((((unsigned long)(n))>>16)&0x3)
+#define DDR0_24_ODT_RD_MAP_CS1_MASK       0x00000300
+#define DDR0_24_ODT_RD_MAP_CS1_ENCODE(n)    ((((unsigned long)(n))&0x3)<<8)
+#define DDR0_24_ODT_RD_MAP_CS1_DECODE(n)    ((((unsigned long)(n))>>8)&0x3)
+#define DDR0_24_ODT_WR_MAP_CS0_MASK       0x00000003
+#define DDR0_24_ODT_WR_MAP_CS0_ENCODE(n)    ((((unsigned long)(n))&0x3)<<0)
+#define DDR0_24_ODT_WR_MAP_CS0_DECODE(n)    ((((unsigned long)(n))>>0)&0x3)
+
+#define DDR0_25                         0x19
+#define DDR0_25_VERSION_MASK              0xFFFF0000 /* Read only */
+#define DDR0_25_VERSION_ENCODE(n)           ((((unsigned long)(n))&0xFFFF)<<16)
+#define DDR0_25_VERSION_DECODE(n)           ((((unsigned long)(n))>>16)&0xFFFF)
+#define DDR0_25_OUT_OF_RANGE_LENGTH_MASK  0x000003FF /* Read only */
+#define DDR0_25_OUT_OF_RANGE_LENGTH_ENCODE(n) ((((unsigned long)(n))&0x3FF)<<0)
+#define DDR0_25_OUT_OF_RANGE_LENGTH_DECODE(n) ((((unsigned long)(n))>>0)&0x3FF)
+
+#define DDR0_26                         0x1A
+#define DDR0_26_TRAS_MAX_MASK             0xFFFF0000
+#define DDR0_26_TRAS_MAX_ENCODE(n)          ((((unsigned long)(n))&0xFFFF)<<16)
+#define DDR0_26_TRAS_MAX_DECODE(n)          ((((unsigned long)(n))>>16)&0xFFFF)
+#define DDR0_26_TREF_MASK                 0x00003FFF
+#define DDR0_26_TREF_ENCODE(n)              ((((unsigned long)(n))&0x3FF)<<0)
+#define DDR0_26_TREF_DECODE(n)              ((((unsigned long)(n))>>0)&0x3FF)
+
+#define DDR0_27                         0x1B
+#define DDR0_27_EMRS_DATA_MASK            0x3FFF0000
+#define DDR0_27_EMRS_DATA_ENCODE(n)         ((((unsigned long)(n))&0x3FFF)<<16)
+#define DDR0_27_EMRS_DATA_DECODE(n)         ((((unsigned long)(n))>>16)&0x3FFF)
+#define DDR0_27_TINIT_MASK                0x0000FFFF
+#define DDR0_27_TINIT_ENCODE(n)             ((((unsigned long)(n))&0xFFFF)<<0)
+#define DDR0_27_TINIT_DECODE(n)             ((((unsigned long)(n))>>0)&0xFFFF)
+
+#define DDR0_28                         0x1C
+#define DDR0_28_EMRS3_DATA_MASK           0x3FFF0000
+#define DDR0_28_EMRS3_DATA_ENCODE(n)        ((((unsigned long)(n))&0x3FFF)<<16)
+#define DDR0_28_EMRS3_DATA_DECODE(n)        ((((unsigned long)(n))>>16)&0x3FFF)
+#define DDR0_28_EMRS2_DATA_MASK           0x00003FFF
+#define DDR0_28_EMRS2_DATA_ENCODE(n)        ((((unsigned long)(n))&0x3FFF)<<0)
+#define DDR0_28_EMRS2_DATA_DECODE(n)        ((((unsigned long)(n))>>0)&0x3FFF)
+
+#define DDR0_29                         0x1D
+
+#define DDR0_30                         0x1E
+
+#define DDR0_31                         0x1F
+#define DDR0_31_XOR_CHECK_BITS_MASK       0x0000FFFF
+#define DDR0_31_XOR_CHECK_BITS_ENCODE(n)    ((((unsigned long)(n))&0xFFFF)<<0)
+#define DDR0_31_XOR_CHECK_BITS_DECODE(n)    ((((unsigned long)(n))>>0)&0xFFFF)
+
+#define DDR0_32                         0x20
+#define DDR0_32_OUT_OF_RANGE_ADDR_MASK    0xFFFFFFFF /* Read only */
+#define DDR0_32_OUT_OF_RANGE_ADDR_ENCODE(n) ((((unsigned long)(n))&0xFFFFFFFF)<<0)
+#define DDR0_32_OUT_OF_RANGE_ADDR_DECODE(n) ((((unsigned long)(n))>>0)&0xFFFFFFFF)
+
+#define DDR0_33                         0x21
+#define DDR0_33_OUT_OF_RANGE_ADDR_MASK    0x00000001 /* Read only */
+#define DDR0_33_OUT_OF_RANGE_ADDR_ENCODE(n) ((((unsigned long)(n))&0x1)<<0)
+#define DDR0_33_OUT_OF_RANGE_ADDR_DECODE(n)               ((((unsigned long)(n))>>0)&0x1)
+
+#define DDR0_34                         0x22
+#define DDR0_34_ECC_U_ADDR_MASK           0xFFFFFFFF /* Read only */
+#define DDR0_34_ECC_U_ADDR_ENCODE(n)        ((((unsigned long)(n))&0xFFFFFFFF)<<0)
+#define DDR0_34_ECC_U_ADDR_DECODE(n)        ((((unsigned long)(n))>>0)&0xFFFFFFFF)
+
+#define DDR0_35                         0x23
+#define DDR0_35_ECC_U_ADDR_MASK           0x00000001 /* Read only */
+#define DDR0_35_ECC_U_ADDR_ENCODE(n)        ((((unsigned long)(n))&0x1)<<0)
+#define DDR0_35_ECC_U_ADDR_DECODE(n)        ((((unsigned long)(n))>>0)&0x1)
+
+#define DDR0_36                         0x24
+#define DDR0_36_ECC_U_DATA_MASK           0xFFFFFFFF /* Read only */
+#define DDR0_36_ECC_U_DATA_ENCODE(n)        ((((unsigned long)(n))&0xFFFFFFFF)<<0)
+#define DDR0_36_ECC_U_DATA_DECODE(n)        ((((unsigned long)(n))>>0)&0xFFFFFFFF)
+
+#define DDR0_37                         0x25
+#define DDR0_37_ECC_U_DATA_MASK           0xFFFFFFFF /* Read only */
+#define DDR0_37_ECC_U_DATA_ENCODE(n)        ((((unsigned long)(n))&0xFFFFFFFF)<<0)
+#define DDR0_37_ECC_U_DATA_DECODE(n)        ((((unsigned long)(n))>>0)&0xFFFFFFFF)
+
+#define DDR0_38                         0x26
+#define DDR0_38_ECC_C_ADDR_MASK           0xFFFFFFFF /* Read only */
+#define DDR0_38_ECC_C_ADDR_ENCODE(n)        ((((unsigned long)(n))&0xFFFFFFFF)<<0)
+#define DDR0_38_ECC_C_ADDR_DECODE(n)        ((((unsigned long)(n))>>0)&0xFFFFFFFF)
+
+#define DDR0_39                         0x27
+#define DDR0_39_ECC_C_ADDR_MASK           0x00000001 /* Read only */
+#define DDR0_39_ECC_C_ADDR_ENCODE(n)        ((((unsigned long)(n))&0x1)<<0)
+#define DDR0_39_ECC_C_ADDR_DECODE(n)        ((((unsigned long)(n))>>0)&0x1)
+
+#define DDR0_40                         0x28
+#define DDR0_40_ECC_C_DATA_MASK           0xFFFFFFFF /* Read only */
+#define DDR0_40_ECC_C_DATA_ENCODE(n)        ((((unsigned long)(n))&0xFFFFFFFF)<<0)
+#define DDR0_40_ECC_C_DATA_DECODE(n)        ((((unsigned long)(n))>>0)&0xFFFFFFFF)
+
+#define DDR0_41                         0x29
+#define DDR0_41_ECC_C_DATA_MASK           0xFFFFFFFF /* Read only */
+#define DDR0_41_ECC_C_DATA_ENCODE(n)        ((((unsigned long)(n))&0xFFFFFFFF)<<0)
+#define DDR0_41_ECC_C_DATA_DECODE(n)        ((((unsigned long)(n))>>0)&0xFFFFFFFF)
+
+#define DDR0_42                         0x2A
+#define DDR0_42_ADDR_PINS_MASK            0x07000000
+#define DDR0_42_ADDR_PINS_ENCODE(n)         ((((unsigned long)(n))&0x7)<<24)
+#define DDR0_42_ADDR_PINS_DECODE(n)         ((((unsigned long)(n))>>24)&0x7)
+#define DDR0_42_CASLAT_LIN_GATE_MASK      0x0000000F
+#define DDR0_42_CASLAT_LIN_GATE_ENCODE(n)   ((((unsigned long)(n))&0xF)<<0)
+#define DDR0_42_CASLAT_LIN_GATE_DECODE(n)   ((((unsigned long)(n))>>0)&0xF)
+
+#define DDR0_43                         0x2B
+#define DDR0_43_TWR_MASK                  0x07000000
+#define DDR0_43_TWR_ENCODE(n)               ((((unsigned long)(n))&0x7)<<24)
+#define DDR0_43_TWR_DECODE(n)               ((((unsigned long)(n))>>24)&0x7)
+#define DDR0_43_APREBIT_MASK              0x000F0000
+#define DDR0_43_APREBIT_ENCODE(n)           ((((unsigned long)(n))&0xF)<<16)
+#define DDR0_43_APREBIT_DECODE(n)           ((((unsigned long)(n))>>16)&0xF)
+#define DDR0_43_COLUMN_SIZE_MASK          0x00000700
+#define DDR0_43_COLUMN_SIZE_ENCODE(n)       ((((unsigned long)(n))&0x7)<<8)
+#define DDR0_43_COLUMN_SIZE_DECODE(n)       ((((unsigned long)(n))>>8)&0x7)
+#define DDR0_43_EIGHT_BANK_MODE_MASK      0x00000001
+#define DDR0_43_EIGHT_BANK_MODE_8_BANKS     0x00000001
+#define DDR0_43_EIGHT_BANK_MODE_4_BANKS     0x00000000
+#define DDR0_43_EIGHT_BANK_MODE_ENCODE(n)   ((((unsigned long)(n))&0x1)<<0)
+#define DDR0_43_EIGHT_BANK_MODE_DECODE(n)   ((((unsigned long)(n))>>0)&0x1)
+
+#define DDR0_44                         0x2C
+#define DDR0_44_TRCD_MASK                 0x000000FF
+#define DDR0_44_TRCD_ENCODE(n)              ((((unsigned long)(n))&0xFF)<<0)
+#define DDR0_44_TRCD_DECODE(n)              ((((unsigned long)(n))>>0)&0xFF)
+
+#endif /* _SPD_SDRAM_DENALI_H_ */
diff --git a/board/lwmon5/u-boot.lds b/board/lwmon5/u-boot.lds
new file mode 100644
index 0000000000..a423f98285
--- /dev/null
+++ b/board/lwmon5/u-boot.lds
@@ -0,0 +1,145 @@
+/*
+ * (C) Copyright 2002
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  .resetvec 0xFFFFFFFC :
+  {
+    *(.resetvec)
+  } = 0xffff
+
+  .bootpg 0xFFFFF000 :
+  {
+    cpu/ppc4xx/start.o	(.bootpg)
+  } = 0xffff
+
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    /* WARNING - the following is hand-optimized to fit within	*/
+    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
+
+    cpu/ppc4xx/start.o	(.text)
+
+    *(.text)
+    *(.fixup)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  . = .;
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+
+  . = .;
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+
+  ppcenv_assert = ASSERT(. < 0xFFFF8000, ".bss section too big, overlaps .ppcenv section. Please update your confguration: CFG_MONITOR_BASE, CFG_MONITOR_LEN and TEXT_BASE may need to be modified.");
+
+  _end = . ;
+  PROVIDE (end = .);
+}
diff --git a/board/pcs440ep/config.mk b/board/pcs440ep/config.mk
index 319c4fa214..4d942ebc71 100644
--- a/board/pcs440ep/config.mk
+++ b/board/pcs440ep/config.mk
@@ -25,6 +25,9 @@
 # PCS440EP board
 #
 
+# Check the U-Boot Image with a SHA1 checksum
+ALL += $(obj)u-boot.sha1
+
 #TEXT_BASE = 0x00001000
 
 ifeq ($(ramsym),1)
diff --git a/board/pcs440ep/flash.c b/board/pcs440ep/flash.c
index ece54781b9..c5a62e2543 100644
--- a/board/pcs440ep/flash.c
+++ b/board/pcs440ep/flash.c
@@ -82,7 +82,9 @@ void flash_print_info(flash_info_t *info)
 	case FLASH_MAN_AMD:	printf ("AMD ");		break;
 	case FLASH_MAN_FUJ:	printf ("FUJITSU ");		break;
 	case FLASH_MAN_SST:	printf ("SST ");		break;
+	case FLASH_MAN_STM:	printf ("ST Micro");		break;
 	case FLASH_MAN_EXCEL:	printf ("Excel Semiconductor "); break;
+	case FLASH_MAN_MX:	printf ("MXIC "); break;
 	default:		printf ("Unknown Vendor ");	break;
 	}
 
@@ -117,6 +119,8 @@ void flash_print_info(flash_info_t *info)
 		break;
 	case FLASH_SST040:	printf ("SST39LF/VF040 (4 Mbit, uniform sector size)\n");
 		break;
+	case STM_ID_M29W040B:	printf ("ST Micro M29W040B (4 Mbit, uniform sector size)\n");
+		break;
 	default:		printf ("Unknown Chip Type\n");
 		break;
 	}
@@ -192,9 +196,15 @@ static ulong flash_get_size(vu_long *addr, flash_info_t *info)
 	case (CFG_FLASH_WORD_SIZE)SST_MANUFACT:
 		info->flash_id = FLASH_MAN_SST;
 		break;
+	case (CFG_FLASH_WORD_SIZE)STM_MANUFACT:
+		info->flash_id = FLASH_MAN_STM;
+		break;
 	case (CFG_FLASH_WORD_SIZE)EXCEL_MANUFACT:
 		info->flash_id = FLASH_MAN_EXCEL;
 		break;
+	case (CFG_FLASH_WORD_SIZE)MX_MANUFACT:
+		info->flash_id = FLASH_MAN_MX;
+		break;
 	default:
 		info->flash_id = FLASH_UNKNOWN;
 		info->sector_count = 0;
@@ -222,6 +232,11 @@ static ulong flash_get_size(vu_long *addr, flash_info_t *info)
 		info->sector_count = 8;
 		info->size = 0x0080000;		/* => 0.5 MB	*/
 		break;
+	case (CFG_FLASH_WORD_SIZE)STM_ID_M29W040B:
+		info->flash_id += FLASH_AM040;
+		info->sector_count = 8;
+		info->size = 0x0080000; /* => 0,5 MB */
+		break;
 
 	case (CFG_FLASH_WORD_SIZE)AMD_ID_LV800T:
 		info->flash_id += FLASH_AM800T;
diff --git a/board/pcs440ep/init.S b/board/pcs440ep/init.S
index 0eee4d8099..36a40c97a3 100644
--- a/board/pcs440ep/init.S
+++ b/board/pcs440ep/init.S
@@ -87,27 +87,32 @@
     .globl tlbtab
 
 tlbtab:
-    tlbtab_start
+	tlbtab_start
 
-    /*
-     * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the
-     * speed up boot process. It is patched after relocation to enable SA_I
-     */
-    tlbentry( CFG_BOOT_BASE_ADDR, SZ_256M, CFG_BOOT_BASE_ADDR, 0, AC_R|AC_W|AC_X|SA_G/*|SA_I*/)
+	/*
+	 * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the
+	 * speed up boot process. It is patched after relocation to enable SA_I
+	 */
+	tlbentry( CFG_BOOT_BASE_ADDR, SZ_256M, CFG_BOOT_BASE_ADDR, 0, AC_R|AC_W|AC_X|SA_G/*|SA_I*/)
 
-    /* TLB-entry for init-ram in dcache (SA_I must be turned off!) */
-    tlbentry( CFG_INIT_RAM_ADDR, SZ_64K, CFG_INIT_RAM_ADDR, 0, AC_R|AC_W|AC_X|SA_G )
+	/* TLB-entry for init-ram in dcache (SA_I must be turned off!) */
+	tlbentry( CFG_INIT_RAM_ADDR, SZ_64K, CFG_INIT_RAM_ADDR, 0, AC_R|AC_W|AC_X|SA_G )
 
-    tlbentry( CFG_SDRAM_BASE, SZ_256M, CFG_SDRAM_BASE, 0, AC_R|AC_W|AC_X|SA_G|SA_I )
-    tlbentry( CFG_PCI_BASE, SZ_256M, CFG_PCI_BASE, 0, AC_R|AC_W|SA_G|SA_I )
+	/*
+	 * TLB entries for SDRAM are not needed on this platform.
+	 * They are dynamically generated in the SPD DDR detection
+	 * routine.
+	 */
 
-    /* PCI */
-    tlbentry( CFG_PCI_MEMBASE, SZ_256M, CFG_PCI_MEMBASE, 0, AC_R|AC_W|SA_G|SA_I )
-    tlbentry( CFG_PCI_MEMBASE1, SZ_256M, CFG_PCI_MEMBASE1, 0, AC_R|AC_W|SA_G|SA_I )
-    tlbentry( CFG_PCI_MEMBASE2, SZ_256M, CFG_PCI_MEMBASE2, 0, AC_R|AC_W|SA_G|SA_I )
-    tlbentry( CFG_PCI_MEMBASE3, SZ_256M, CFG_PCI_MEMBASE3, 0, AC_R|AC_W|SA_G|SA_I )
+	tlbentry( CFG_PCI_BASE, SZ_256M, CFG_PCI_BASE, 0, AC_R|AC_W|SA_G|SA_I )
 
-    /* USB 2.0 Device */
-    tlbentry( CFG_USB_DEVICE, SZ_1K, 0x50000000, 0, AC_R|AC_W|SA_G|SA_I )
+	/* PCI */
+	tlbentry( CFG_PCI_MEMBASE, SZ_256M, CFG_PCI_MEMBASE, 0, AC_R|AC_W|SA_G|SA_I )
+	tlbentry( CFG_PCI_MEMBASE1, SZ_256M, CFG_PCI_MEMBASE1, 0, AC_R|AC_W|SA_G|SA_I )
+	tlbentry( CFG_PCI_MEMBASE2, SZ_256M, CFG_PCI_MEMBASE2, 0, AC_R|AC_W|SA_G|SA_I )
+	tlbentry( CFG_PCI_MEMBASE3, SZ_256M, CFG_PCI_MEMBASE3, 0, AC_R|AC_W|SA_G|SA_I )
 
-    tlbtab_end
+	/* USB 2.0 Device */
+	tlbentry( CFG_USB_DEVICE, SZ_1K, 0x50000000, 0, AC_R|AC_W|SA_G|SA_I )
+
+	tlbtab_end
diff --git a/board/pcs440ep/pcs440ep.c b/board/pcs440ep/pcs440ep.c
index 8858f0a5e5..0e34a76cb9 100644
--- a/board/pcs440ep/pcs440ep.c
+++ b/board/pcs440ep/pcs440ep.c
@@ -23,20 +23,115 @@
 
 #include <common.h>
 #include <ppc4xx.h>
+#include <malloc.h>
+#include <command.h>
+#include <crc.h>
 #include <asm/processor.h>
 #include <spd_sdram.h>
+#include <status_led.h>
+#include <sha1.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
 extern flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips	*/
 
-static void set_leds(int val)
+unsigned char	sha1_checksum[SHA1_SUM_LEN];
+
+/* swap 4 Bits (Bit0 = Bit3, Bit1 = Bit2, Bit2 = Bit1 and Bit3 = Bit0) */
+unsigned char swapbits[16] = {0x0, 0x8, 0x4, 0xc, 0x2, 0xa, 0x6, 0xe,
+			      0x1, 0x9, 0x5, 0xd, 0x3, 0xb, 0x7, 0xf};
+
+static void set_leds (int val)
+{
+	out32(GPIO0_OR, (in32 (GPIO0_OR) & ~0x78000000) | (val << 27));
+}
+
+#define GET_LEDS ((in32 (GPIO0_OR) & 0x78000000) >> 27)
+
+void __led_init (led_id_t mask, int state)
+{
+	int	val = GET_LEDS;
+
+	if (state == STATUS_LED_ON)
+		val |= mask;
+	else
+		val &= ~mask;
+	set_leds (val);
+}
+
+void __led_set (led_id_t mask, int state)
+{
+	int	val = GET_LEDS;
+
+	if (state == STATUS_LED_ON)
+		val |= mask;
+	else if (state == STATUS_LED_OFF)
+		val &= ~mask;
+	set_leds (val);
+}
+
+void __led_toggle (led_id_t mask)
 {
-	unsigned char led[16] = {0x0, 0x8, 0x4, 0xc, 0x2, 0xa, 0x6, 0xe,
-				 0x1, 0x9, 0x5, 0xd, 0x3, 0xb, 0x7, 0xf};
-	out32(GPIO0_OR, (in32(GPIO0_OR) & ~0x78000000) | (led[val] << 27));
+	int	val = GET_LEDS;
+
+	val ^= mask;
+	set_leds (val);
 }
 
+static void status_led_blink (void)
+{
+	int	i;
+	int	val = GET_LEDS;
+
+	/* set all LED which are on, to state BLINKING */
+	for (i = 0; i < 4; i++) {
+		if (val & 0x01) status_led_set (3 - i, STATUS_LED_BLINKING);
+		else status_led_set (3 - i, STATUS_LED_OFF);
+		val = val >> 1;
+	}
+}
+
+#if defined(CONFIG_SHOW_BOOT_PROGRESS)
+void show_boot_progress (int val)
+{
+	/* find all valid Codes for val in README */
+	if (val == -30) return;
+	if (val < 0) {
+		/* smthing goes wrong */
+		status_led_blink ();
+		return;
+	}
+	switch (val) {
+		case 1:
+			/* validating Image */
+			status_led_set (0, STATUS_LED_OFF);
+			status_led_set (1, STATUS_LED_ON);
+			status_led_set (2, STATUS_LED_ON);
+			break;
+		case 15:
+			/* booting */
+			status_led_set (0, STATUS_LED_ON);
+			status_led_set (1, STATUS_LED_ON);
+			status_led_set (2, STATUS_LED_ON);
+			break;
+#if 0
+		case 64:
+			/* starting Ethernet configuration */
+			status_led_set (0, STATUS_LED_OFF);
+			status_led_set (1, STATUS_LED_OFF);
+			status_led_set (2, STATUS_LED_ON);
+			break;
+#endif
+		case 80:
+			/* loading Image */
+			status_led_set (0, STATUS_LED_ON);
+			status_led_set (1, STATUS_LED_OFF);
+			status_led_set (2, STATUS_LED_ON);
+			break;
+	}
+}
+#endif
+
 int board_early_init_f(void)
 {
 	register uint reg;
@@ -85,6 +180,254 @@ int board_early_init_f(void)
 	return 0;
 }
 
+#define EEPROM_LEN	256
+void load_sernum_ethaddr (void)
+{
+	int	ret;
+	char	buf[EEPROM_LEN];
+	char	mac[32];
+	char	*use_eeprom;
+	u16	checksumcrc16 = 0;
+
+	/* read the MACs from EEprom */
+	status_led_set (0, STATUS_LED_ON);
+	status_led_set (1, STATUS_LED_ON);
+	ret = eeprom_read (CFG_I2C_EEPROM_ADDR, 0, (uchar *)buf, EEPROM_LEN);
+	if (ret == 0) {
+		checksumcrc16 = cyg_crc16 ((uchar *)buf, EEPROM_LEN - 2);
+		/* check, if the EEprom is programmed:
+		 * - The Prefix(Byte 0,1,2) is equal to "ATR"
+		 * - The checksum, stored in the last 2 Bytes, is correct
+		 */
+		if ((strncmp (buf,"ATR",3) != 0) ||
+		    ((checksumcrc16 >> 8) != buf[EEPROM_LEN - 2]) ||
+		    ((checksumcrc16 & 0xff) != buf[EEPROM_LEN - 1])) {
+			/* EEprom is not programmed */
+			printf("%s: EEPROM Checksum not OK\n", __FUNCTION__);
+		} else {
+			/* get the MACs */
+			sprintf (mac, "%02x:%02x:%02x:%02x:%02x:%02x",
+				buf[3],
+				buf[4],
+				buf[5],
+				buf[6],
+				buf[7],
+				buf[8]);
+			setenv ("ethaddr", (char *) mac);
+			sprintf (mac, "%02x:%02x:%02x:%02x:%02x:%02x",
+				buf[9],
+				buf[10],
+				buf[11],
+				buf[12],
+				buf[13],
+				buf[14]);
+			setenv ("eth1addr", (char *) mac);
+			return;
+		}
+	}
+
+	/* some error reading the EEprom */
+	if ((use_eeprom = getenv ("use_eeprom_ethaddr")) == NULL) {
+		/* dont use bootcmd */
+		setenv("bootdelay", "-1");
+		return;
+	}
+	/* == default ? use standard */
+	if (strncmp (use_eeprom, "default", 7) == 0) {
+		return;
+	}
+	/* Env doesnt exist -> hang */
+	status_led_blink ();
+	hang ();
+	return;
+}
+
+#ifdef CONFIG_PREBOOT
+
+static uchar kbd_magic_prefix[]		= "key_magic";
+static uchar kbd_command_prefix[]	= "key_cmd";
+
+struct kbd_data_t {
+	char s1;
+	char s2;
+};
+
+struct kbd_data_t* get_keys (struct kbd_data_t *kbd_data)
+{
+	char *val;
+	unsigned long tmp;
+
+	/* use the DIPs for some bootoptions */
+	val = getenv (ENV_NAME_DIP);
+	tmp = simple_strtoul (val, NULL, 16);
+
+	kbd_data->s2 = (tmp & 0x0f);
+	kbd_data->s1 = (tmp & 0xf0) >> 4;
+	return kbd_data;
+}
+
+static int compare_magic (const struct kbd_data_t *kbd_data, char *str)
+{
+	char s1 = str[0];
+
+	if (s1 >= '0' && s1 <= '9')
+		s1 -= '0';
+	else if (s1 >= 'a' && s1 <= 'f')
+		s1 = s1 - 'a' + 10;
+	else if (s1 >= 'A' && s1 <= 'F')
+		s1 = s1 - 'A' + 10;
+	else
+		return -1;
+
+	if (s1 != kbd_data->s1) return -1;
+
+	s1 = str[1];
+	if (s1 >= '0' && s1 <= '9')
+		s1 -= '0';
+	else if (s1 >= 'a' && s1 <= 'f')
+		s1 = s1 - 'a' + 10;
+	else if (s1 >= 'A' && s1 <= 'F')
+		s1 = s1 - 'A' + 10;
+	else
+		return -1;
+
+	if (s1 != kbd_data->s2) return -1;
+	return 0;
+}
+
+static char *key_match (const struct kbd_data_t *kbd_data)
+{
+	char magic[sizeof (kbd_magic_prefix) + 1];
+	char *suffix;
+	char *kbd_magic_keys;
+
+	/*
+	 * The following string defines the characters that can be appended
+	 * to "key_magic" to form the names of environment variables that
+	 * hold "magic" key codes, i. e. such key codes that can cause
+	 * pre-boot actions. If the string is empty (""), then only
+	 * "key_magic" is checked (old behaviour); the string "125" causes
+	 * checks for "key_magic1", "key_magic2" and "key_magic5", etc.
+	 */
+	if ((kbd_magic_keys = getenv ("magic_keys")) == NULL)
+		kbd_magic_keys = "";
+
+	/* loop over all magic keys;
+	 * use '\0' suffix in case of empty string
+	 */
+	for (suffix = kbd_magic_keys; *suffix ||
+		     suffix == kbd_magic_keys; ++suffix) {
+		sprintf (magic, "%s%c", kbd_magic_prefix, *suffix);
+		if (compare_magic (kbd_data, getenv (magic)) == 0) {
+			char cmd_name[sizeof (kbd_command_prefix) + 1];
+			char *cmd;
+
+			sprintf (cmd_name, "%s%c", kbd_command_prefix, *suffix);
+			cmd = getenv (cmd_name);
+
+			return (cmd);
+		}
+	}
+	return (NULL);
+}
+
+#endif /* CONFIG_PREBOOT */
+
+static int pcs440ep_readinputs (void)
+{
+	int	i;
+	char	value[20];
+
+	/* read the inputs and set the Envvars */
+	/* Revision Level Bit 26 - 29 */
+	i = ((in32 (GPIO0_IR) & 0x0000003c) >> 2);
+	i = swapbits[i];
+	sprintf (value, "%02x", i);
+	setenv (ENV_NAME_REVLEV, value);
+	/* Solder Switch Bit 30 - 33 */
+	i = (in32 (GPIO0_IR) & 0x00000003) << 2;
+	i += (in32 (GPIO1_IR) & 0xc0000000) >> 30;
+	i = swapbits[i];
+	sprintf (value, "%02x", i);
+	setenv (ENV_NAME_SOLDER, value);
+	/* DIP Switch Bit 49 - 56 */
+	i = ((in32 (GPIO1_IR) & 0x00007f80) >> 7);
+	i = (swapbits[i & 0x0f] << 4) + swapbits[(i & 0xf0) >> 4];
+	sprintf (value, "%02x", i);
+	setenv (ENV_NAME_DIP, value);
+	return 0;
+}
+
+
+#if defined(CONFIG_SHA1_CHECK_UB_IMG)
+/*************************************************************************
+ * calculate a SHA1 sum for the U-Boot image in Flash.
+ *
+ ************************************************************************/
+static int pcs440ep_sha1 (int docheck)
+{
+	unsigned char *data;
+	unsigned char *ptroff;
+	unsigned char output[20];
+	unsigned char org[20];
+	int	i, len = CONFIG_SHA1_LEN;
+
+	memcpy ((char *)CFG_LOAD_ADDR, (char *)CONFIG_SHA1_START, len);
+	data = (unsigned char *)CFG_LOAD_ADDR;
+	ptroff = &data[len + SHA1_SUM_POS];
+
+	for (i = 0; i < SHA1_SUM_LEN; i++) {
+		org[i] = ptroff[i];
+		ptroff[i] = 0;
+	}
+
+	sha1_csum ((unsigned char *) data, len, (unsigned char *)output);
+
+	if (docheck == 2) {
+		for (i = 0; i < 20 ; i++) {
+			printf("%02X ", output[i]);
+		}
+		printf("\n");
+	}
+	if (docheck == 1) {
+		for (i = 0; i < 20 ; i++) {
+			if (org[i] != output[i]) return 1;
+		}
+	}
+	return 0;
+}
+
+/*************************************************************************
+ * do some checks after the SHA1 checksum from the U-Boot Image was
+ * calculated.
+ *
+ ************************************************************************/
+static void pcs440ep_checksha1 (void)
+{
+	int	ret;
+	char	*cs_test;
+
+	status_led_set (0, STATUS_LED_OFF);
+	status_led_set (1, STATUS_LED_OFF);
+	status_led_set (2, STATUS_LED_ON);
+	ret = pcs440ep_sha1 (1);
+	if (ret == 0) return;
+
+	if ((cs_test = getenv ("cs_test")) == NULL) {
+		/* Env doesnt exist -> hang */
+		status_led_blink ();
+		hang ();
+	}
+
+	if (strncmp (cs_test, "off", 3) == 0) {
+		printf ("SHA1 U-Boot sum NOT ok!\n");
+		setenv ("bootdelay", "-1");
+	}
+}
+#else
+static __inline__ void pcs440ep_checksha1 (void) { do {} while (0);}
+#endif
+
 int misc_init_r (void)
 {
 	uint pbcr;
@@ -139,6 +482,18 @@ int misc_init_r (void)
 			    CFG_ENV_ADDR_REDUND + 2*CFG_ENV_SECT_SIZE - 1,
 			    &flash_info[1]);
 
+	pcs440ep_readinputs ();
+	pcs440ep_checksha1 ();
+#ifdef CONFIG_PREBOOT
+	{
+		struct kbd_data_t kbd_data;
+		/* Decode keys */
+		char *str = strdup (key_match (get_keys (&kbd_data)));
+		/* Set or delete definition */
+		setenv ("preboot", str);
+		free (str);
+	}
+#endif /* CONFIG_PREBOOT */
 	return 0;
 }
 
@@ -156,13 +511,31 @@ int checkboard(void)
 	return (0);
 }
 
+void spd_ddr_init_hang (void)
+{
+	status_led_set (0, STATUS_LED_OFF);
+	status_led_set (1, STATUS_LED_ON);
+	/* we cannot use hang() because we are still running from
+	   Flash, and so the status_led driver is not initialized */
+	puts ("### ERROR ### Please RESET the board ###\n");
+	for (;;) {
+		__led_toggle (4);
+		udelay (100000);
+	}
+}
+
 long int initdram (int board_type)
 {
 	long dram_size = 0;
 
-	set_leds(1);			/* display boot info counter */
+	status_led_set (0, STATUS_LED_ON);
+	status_led_set (1, STATUS_LED_OFF);
 	dram_size = spd_sdram();
-	set_leds(2);			/* display boot info counter */
+	status_led_set (0, STATUS_LED_OFF);
+	status_led_set (1, STATUS_LED_ON);
+	if (dram_size == 0) {
+		hang();
+	}
 
 	return dram_size;
 }
@@ -217,7 +590,7 @@ int testdram(void)
  *	certain pre-initialization actions.
  *
  ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT)
+#if defined(CONFIG_PCI)
 int pci_pre_init(struct pci_controller *hose)
 {
 	unsigned long addr;
@@ -258,7 +631,7 @@ int pci_pre_init(struct pci_controller *hose)
 
 	return 1;
 }
-#endif				/* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */
+#endif	/* defined(CONFIG_PCI) */
 
 /*************************************************************************
  *  pci_target_init
@@ -377,3 +750,132 @@ void hw_watchdog_reset(void)
 
 }
 #endif
+
+/*************************************************************************
+ * "led" Commando for the U-Boot shell
+ *
+ ************************************************************************/
+int do_led (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	int	rcode = 0, i;
+	ulong	pattern = 0;
+
+	pattern = simple_strtoul (argv[1], NULL, 16);
+	if (pattern > 0x400) {
+		int	val = GET_LEDS;
+		printf ("led: %x\n", val);
+		return rcode;
+	}
+	if (pattern > 0x200) {
+		status_led_blink ();
+		hang ();
+		return rcode;
+	}
+	if (pattern > 0x100) {
+		status_led_blink ();
+		return rcode;
+	}
+	pattern &= 0x0f;
+	for (i = 0; i < 4; i++) {
+		if (pattern & 0x01) status_led_set (i, STATUS_LED_ON);
+		else status_led_set (i, STATUS_LED_OFF);
+		pattern = pattern >> 1;
+	}
+	return rcode;
+}
+
+U_BOOT_CMD(
+ 	led,	2,	1,	do_led,
+ 	"led [bitmask]   - set the DIAG-LED\n",
+	"[bitmask] 0x01 = DIAG 1 on\n"
+	"              0x02 = DIAG 2 on\n"
+	"              0x04 = DIAG 3 on\n"
+	"              0x08 = DIAG 4 on\n"
+	"              > 0x100 set the LED, who are on, to state blinking\n"
+);
+
+#if defined(CONFIG_SHA1_CHECK_UB_IMG)
+/*************************************************************************
+ * "sha1" Commando for the U-Boot shell
+ *
+ ************************************************************************/
+int do_sha1 (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	int	rcode = -1;
+
+	if (argc < 2) {
+  usage:
+		printf ("Usage:\n%s\n", cmdtp->usage);
+		return 1;
+	}
+
+	if (argc >= 3) {
+		unsigned char *data;
+		unsigned char output[20];
+		int	len;
+		int	i;
+
+		data = (unsigned char *)simple_strtoul (argv[1], NULL, 16);
+		len = simple_strtoul (argv[2], NULL, 16);
+		sha1_csum (data, len, (unsigned char *)output);
+		printf ("U-Boot sum:\n");
+		for (i = 0; i < 20 ; i++) {
+			printf ("%02X ", output[i]);
+		}
+		printf ("\n");
+		if (argc == 4) {
+			data = (unsigned char *)simple_strtoul (argv[3], NULL, 16);
+			memcpy (data, output, 20);
+		}
+		return 0;
+	}
+	if (argc == 2) {
+		char *ptr = argv[1];
+		if (*ptr != '-') goto usage;
+		ptr++;
+		if ((*ptr == 'c') || (*ptr == 'C')) {
+			rcode = pcs440ep_sha1 (1);
+			printf ("SHA1 U-Boot sum %sok!\n", (rcode != 0) ? "not " : "");
+		} else if ((*ptr == 'p') || (*ptr == 'P')) {
+			rcode = pcs440ep_sha1 (2);
+		} else {
+			rcode = pcs440ep_sha1 (0);
+		}
+		return rcode;
+	}
+	return rcode;
+}
+
+U_BOOT_CMD(
+ 	sha1,	4,	1,	do_sha1,
+ 	"sha1    - calculate the SHA1 Sum\n",
+	"address len [addr]  calculate the SHA1 sum [save at addr]\n"
+	"     -p calculate the SHA1 sum from the U-Boot image in flash and print\n"
+	"     -c check the U-Boot image in flash\n"
+);
+#endif
+
+#ifdef CONFIG_IDE_PREINIT
+int ide_preinit (void)
+{
+	/* Set True IDE Mode */
+	out32 (GPIO0_OR, (in32 (GPIO0_OR) | 0x00100000));
+	out32 (GPIO0_OR, (in32 (GPIO0_OR) | 0x00200000));
+	out32 (GPIO1_OR, (in32 (GPIO1_OR) & ~0x00008040));
+	udelay (100000);
+	return 0;
+}
+#endif
+
+#if defined (CFG_CMD_IDE) && defined (CONFIG_IDE_RESET)
+void ide_set_reset (int idereset)
+{
+	debug ("ide_reset(%d)\n", idereset);
+	if (idereset == 0) {
+		out32 (GPIO0_OR, (in32 (GPIO0_OR) | 0x00200000));
+	} else {
+		out32 (GPIO0_OR, (in32 (GPIO0_OR) & ~0x00200000));
+	}
+	udelay (10000);
+}
+#endif /* defined (CFG_CMD_IDE) && defined (CONFIG_IDE_RESET) */
diff --git a/board/pcs440ep/u-boot.lds b/board/pcs440ep/u-boot.lds
index 6ab476ab14..6506ccdcf3 100644
--- a/board/pcs440ep/u-boot.lds
+++ b/board/pcs440ep/u-boot.lds
@@ -65,6 +65,7 @@ SECTIONS
   {
     cpu/ppc4xx/start.o	(.text)
     board/pcs440ep/init.o	(.text)
+    lib_generic/sha1.o		(.text)
 
     *(.text)
     *(.fixup)
diff --git a/board/prodrive/alpr/alpr.c b/board/prodrive/alpr/alpr.c
index 5abc87dde6..b76449989b 100644
--- a/board/prodrive/alpr/alpr.c
+++ b/board/prodrive/alpr/alpr.c
@@ -172,7 +172,7 @@ int testdram (void)
  *	certain pre-initialization actions.
  *
  ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT)
+#if defined(CONFIG_PCI)
 int pci_pre_init(struct pci_controller * hose )
 {
 	unsigned long strap;
@@ -192,7 +192,7 @@ int pci_pre_init(struct pci_controller * hose )
 
 	return 1;
 }
-#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */
+#endif /* defined(CONFIG_PCI) */
 
 /*************************************************************************
  *  pci_target_init
diff --git a/board/prodrive/p3p440/p3p440.c b/board/prodrive/p3p440/p3p440.c
index 2f28e9d87a..1a8aacbdf1 100644
--- a/board/prodrive/p3p440/p3p440.c
+++ b/board/prodrive/p3p440/p3p440.c
@@ -176,7 +176,7 @@ int misc_init_r (void)
  *	certain pre-initialization actions.
  *
  ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT)
+#if defined(CONFIG_PCI)
 int pci_pre_init(struct pci_controller *hose)
 {
 	unsigned long strap;
@@ -193,7 +193,7 @@ int pci_pre_init(struct pci_controller *hose)
 
 	return 1;
 }
-#endif				/* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */
+#endif	/* defined(CONFIG_PCI) */
 
 /*************************************************************************
  *  pci_target_init
diff --git a/board/sandburst/common/sb_common.c b/board/sandburst/common/sb_common.c
index 7816472516..8a831fa35f 100644
--- a/board/sandburst/common/sb_common.c
+++ b/board/sandburst/common/sb_common.c
@@ -313,7 +313,7 @@ long int fixed_sdram (void)
  *	certain pre-initialization actions.
  *
  ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT)
+#if defined(CONFIG_PCI)
 int pci_pre_init(struct pci_controller * hose )
 {
 	unsigned long strap;
@@ -330,7 +330,7 @@ int pci_pre_init(struct pci_controller * hose )
 
 	return 1;
 }
-#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */
+#endif /* defined(CONFIG_PCI) */
 
 /*************************************************************************
  *  pci_target_init
diff --git a/board/sc520_cdp/sc520_cdp.c b/board/sc520_cdp/sc520_cdp.c
index b6add59bb4..f6f0e72443 100644
--- a/board/sc520_cdp/sc520_cdp.c
+++ b/board/sc520_cdp/sc520_cdp.c
@@ -507,6 +507,7 @@ int dram_init(void)
 
 void show_boot_progress(int val)
 {
+	if (val < -32) val = -1;  /* let things compatible */
 	outb(val&0xff, 0x80);
 	outb((val&0xff00)>>8, 0x680);
 }
diff --git a/board/sc520_spunk/sc520_spunk.c b/board/sc520_spunk/sc520_spunk.c
index ed226fd642..d119a7d997 100644
--- a/board/sc520_spunk/sc520_spunk.c
+++ b/board/sc520_spunk/sc520_spunk.c
@@ -507,6 +507,7 @@ void show_boot_progress(int val)
 {
 	int version = read_mmcr_byte(SC520_SYSINFO);
 
+	if (val < -32) val = -1;  /* let things compatible */
 	if (version == 0) {
 		/* PIO31-PIO16 Data */
 		write_mmcr_word(SC520_PIODATA31_16,
diff --git a/board/smdk2400/lowlevel_init.S b/board/smdk2400/lowlevel_init.S
index a5de806af5..a7959f391d 100644
--- a/board/smdk2400/lowlevel_init.S
+++ b/board/smdk2400/lowlevel_init.S
@@ -117,7 +117,7 @@
 #define TREFMD	0x0	/* CBR(CAS before RAS)/auto refresh */
 #define Trp	0x0	/* 2 clk */
 #define Trc	0x3	/* 7 clk */
-#define Tchr	0x2 	/* 3 clk */
+#define Tchr	0x2	/* 3 clk */
 
 #define REFCNT	1113	/* period=15.6 us, HCLK=60Mhz, (2048+1-15.6*66) */
 
diff --git a/board/stxssa/stxssa.c b/board/stxssa/stxssa.c
index 0fb233d818..5882124150 100644
--- a/board/stxssa/stxssa.c
+++ b/board/stxssa/stxssa.c
@@ -52,147 +52,147 @@ long int fixed_sdram (void);
 const iop_conf_t iop_conf_tab[4][32] = {
 
     /* Port A configuration */
-    {   /*            conf ppar psor pdir podr pdat */
-	/* PA31 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 TxENB */
-	/* PA30 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 TxClav   */
-	/* PA29 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 TxSOC  */
-	/* PA28 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 RxENB */
-	/* PA27 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 RxSOC */
-	/* PA26 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 RxClav */
-	/* PA25 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[0] */
-	/* PA24 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[1] */
-	/* PA23 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[2] */
-	/* PA22 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[3] */
-	/* PA21 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[4] */
-	/* PA20 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[5] */
-	/* PA19 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[6] */
-	/* PA18 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[7] */
-	/* PA17 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[7] */
-	/* PA16 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[6] */
-	/* PA15 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[5] */
-	/* PA14 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[4] */
-	/* PA13 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[3] */
-	/* PA12 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[2] */
-	/* PA11 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[1] */
-	/* PA10 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[0] */
-	/* PA9  */ {   0,   1,   1,   1,   0,   0   }, /* FCC1 L1TXD */
-	/* PA8  */ {   0,   1,   1,   0,   0,   0   }, /* FCC1 L1RXD */
-	/* PA7  */ {   0,   0,   0,   1,   0,   0   }, /* PA7 */
-	/* PA6  */ {   0,   1,   1,   1,   0,   0   }, /* TDM A1 L1RSYNC */
-	/* PA5  */ {   0,   0,   0,   1,   0,   0   }, /* PA5 */
-	/* PA4  */ {   0,   0,   0,   1,   0,   0   }, /* PA4 */
-	/* PA3  */ {   0,   0,   0,   1,   0,   0   }, /* PA3 */
-	/* PA2  */ {   0,   0,   0,   1,   0,   0   }, /* PA2 */
-	/* PA1  */ {   1,   0,   0,   0,   0,   0   }, /* FREERUN */
-	/* PA0  */ {   0,   0,   0,   1,   0,   0   }  /* PA0 */
+    {	/*	      conf ppar psor pdir podr pdat */
+	/* PA31 */ {   0,   1,	 0,   1,   0,	0   }, /* FCC1 TxENB */
+	/* PA30 */ {   0,   1,	 0,   0,   0,	0   }, /* FCC1 TxClav	*/
+	/* PA29 */ {   0,   1,	 0,   1,   0,	0   }, /* FCC1 TxSOC  */
+	/* PA28 */ {   0,   1,	 0,   1,   0,	0   }, /* FCC1 RxENB */
+	/* PA27 */ {   0,   1,	 0,   0,   0,	0   }, /* FCC1 RxSOC */
+	/* PA26 */ {   0,   1,	 0,   0,   0,	0   }, /* FCC1 RxClav */
+	/* PA25 */ {   0,   1,	 0,   1,   0,	0   }, /* FCC1 ATMTXD[0] */
+	/* PA24 */ {   0,   1,	 0,   1,   0,	0   }, /* FCC1 ATMTXD[1] */
+	/* PA23 */ {   0,   1,	 0,   1,   0,	0   }, /* FCC1 ATMTXD[2] */
+	/* PA22 */ {   0,   1,	 0,   1,   0,	0   }, /* FCC1 ATMTXD[3] */
+	/* PA21 */ {   0,   1,	 0,   1,   0,	0   }, /* FCC1 ATMTXD[4] */
+	/* PA20 */ {   0,   1,	 0,   1,   0,	0   }, /* FCC1 ATMTXD[5] */
+	/* PA19 */ {   0,   1,	 0,   1,   0,	0   }, /* FCC1 ATMTXD[6] */
+	/* PA18 */ {   0,   1,	 0,   1,   0,	0   }, /* FCC1 ATMTXD[7] */
+	/* PA17 */ {   0,   1,	 0,   0,   0,	0   }, /* FCC1 ATMRXD[7] */
+	/* PA16 */ {   0,   1,	 0,   0,   0,	0   }, /* FCC1 ATMRXD[6] */
+	/* PA15 */ {   0,   1,	 0,   0,   0,	0   }, /* FCC1 ATMRXD[5] */
+	/* PA14 */ {   0,   1,	 0,   0,   0,	0   }, /* FCC1 ATMRXD[4] */
+	/* PA13 */ {   0,   1,	 0,   0,   0,	0   }, /* FCC1 ATMRXD[3] */
+	/* PA12 */ {   0,   1,	 0,   0,   0,	0   }, /* FCC1 ATMRXD[2] */
+	/* PA11 */ {   0,   1,	 0,   0,   0,	0   }, /* FCC1 ATMRXD[1] */
+	/* PA10 */ {   0,   1,	 0,   0,   0,	0   }, /* FCC1 ATMRXD[0] */
+	/* PA9	*/ {   0,   1,	 1,   1,   0,	0   }, /* FCC1 L1TXD */
+	/* PA8	*/ {   0,   1,	 1,   0,   0,	0   }, /* FCC1 L1RXD */
+	/* PA7	*/ {   0,   0,	 0,   1,   0,	0   }, /* PA7 */
+	/* PA6	*/ {   0,   1,	 1,   1,   0,	0   }, /* TDM A1 L1RSYNC */
+	/* PA5	*/ {   0,   0,	 0,   1,   0,	0   }, /* PA5 */
+	/* PA4	*/ {   0,   0,	 0,   1,   0,	0   }, /* PA4 */
+	/* PA3	*/ {   0,   0,	 0,   1,   0,	0   }, /* PA3 */
+	/* PA2	*/ {   0,   0,	 0,   1,   0,	0   }, /* PA2 */
+	/* PA1	*/ {   1,   0,	 0,   0,   0,	0   }, /* FREERUN */
+	/* PA0	*/ {   0,   0,	 0,   1,   0,	0   }  /* PA0 */
     },
 
     /* Port B configuration */
-    {   /*            conf ppar psor pdir podr pdat */
-	/* PB31 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TX_ER */
-	/* PB30 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RX_DV */
-	/* PB29 */ {   1,   1,   1,   1,   0,   0   }, /* FCC2 MII TX_EN */
-	/* PB28 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RX_ER */
-	/* PB27 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII COL */
-	/* PB26 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII CRS */
-	/* PB25 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[3] */
-	/* PB24 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[2] */
-	/* PB23 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[1] */
-	/* PB22 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[0] */
-	/* PB21 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[0] */
-	/* PB20 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[1] */
-	/* PB19 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[2] */
-	/* PB18 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[3] */
-	/* PB17 */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:RX_DIV */
-	/* PB16 */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:RX_ERR */
-	/* PB15 */ {   0,   1,   0,   1,   0,   0   }, /* FCC3:TX_ERR */
-	/* PB14 */ {   0,   1,   0,   1,   0,   0   }, /* FCC3:TX_EN */
-	/* PB13 */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:COL */
-	/* PB12 */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:CRS */
-	/* PB11 */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:RXD */
-	/* PB10 */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:RXD */
-	/* PB9  */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:RXD */
-	/* PB8  */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:RXD */
-	/* PB7  */ {   0,   1,   0,   1,   0,   0   }, /* FCC3:TXD */
-	/* PB6  */ {   0,   1,   0,   1,   0,   0   }, /* FCC3:TXD */
-	/* PB5  */ {   0,   1,   0,   1,   0,   0   }, /* FCC3:TXD */
-	/* PB4  */ {   0,   1,   0,   1,   0,   0   }, /* FCC3:TXD */
-	/* PB3  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
-	/* PB2  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
-	/* PB1  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
-	/* PB0  */ {   0,   0,   0,   0,   0,   0   }  /* pin doesn't exist */
+    {	/*	      conf ppar psor pdir podr pdat */
+	/* PB31 */ {   1,   1,	 0,   1,   0,	0   }, /* FCC2 MII TX_ER */
+	/* PB30 */ {   1,   1,	 0,   0,   0,	0   }, /* FCC2 MII RX_DV */
+	/* PB29 */ {   1,   1,	 1,   1,   0,	0   }, /* FCC2 MII TX_EN */
+	/* PB28 */ {   1,   1,	 0,   0,   0,	0   }, /* FCC2 MII RX_ER */
+	/* PB27 */ {   1,   1,	 0,   0,   0,	0   }, /* FCC2 MII COL */
+	/* PB26 */ {   1,   1,	 0,   0,   0,	0   }, /* FCC2 MII CRS */
+	/* PB25 */ {   1,   1,	 0,   1,   0,	0   }, /* FCC2 MII TxD[3] */
+	/* PB24 */ {   1,   1,	 0,   1,   0,	0   }, /* FCC2 MII TxD[2] */
+	/* PB23 */ {   1,   1,	 0,   1,   0,	0   }, /* FCC2 MII TxD[1] */
+	/* PB22 */ {   1,   1,	 0,   1,   0,	0   }, /* FCC2 MII TxD[0] */
+	/* PB21 */ {   1,   1,	 0,   0,   0,	0   }, /* FCC2 MII RxD[0] */
+	/* PB20 */ {   1,   1,	 0,   0,   0,	0   }, /* FCC2 MII RxD[1] */
+	/* PB19 */ {   1,   1,	 0,   0,   0,	0   }, /* FCC2 MII RxD[2] */
+	/* PB18 */ {   1,   1,	 0,   0,   0,	0   }, /* FCC2 MII RxD[3] */
+	/* PB17 */ {   0,   1,	 0,   0,   0,	0   }, /* FCC3:RX_DIV */
+	/* PB16 */ {   0,   1,	 0,   0,   0,	0   }, /* FCC3:RX_ERR */
+	/* PB15 */ {   0,   1,	 0,   1,   0,	0   }, /* FCC3:TX_ERR */
+	/* PB14 */ {   0,   1,	 0,   1,   0,	0   }, /* FCC3:TX_EN */
+	/* PB13 */ {   0,   1,	 0,   0,   0,	0   }, /* FCC3:COL */
+	/* PB12 */ {   0,   1,	 0,   0,   0,	0   }, /* FCC3:CRS */
+	/* PB11 */ {   0,   1,	 0,   0,   0,	0   }, /* FCC3:RXD */
+	/* PB10 */ {   0,   1,	 0,   0,   0,	0   }, /* FCC3:RXD */
+	/* PB9	*/ {   0,   1,	 0,   0,   0,	0   }, /* FCC3:RXD */
+	/* PB8	*/ {   0,   1,	 0,   0,   0,	0   }, /* FCC3:RXD */
+	/* PB7	*/ {   0,   1,	 0,   1,   0,	0   }, /* FCC3:TXD */
+	/* PB6	*/ {   0,   1,	 0,   1,   0,	0   }, /* FCC3:TXD */
+	/* PB5	*/ {   0,   1,	 0,   1,   0,	0   }, /* FCC3:TXD */
+	/* PB4	*/ {   0,   1,	 0,   1,   0,	0   }, /* FCC3:TXD */
+	/* PB3	*/ {   0,   0,	 0,   0,   0,	0   }, /* pin doesn't exist */
+	/* PB2	*/ {   0,   0,	 0,   0,   0,	0   }, /* pin doesn't exist */
+	/* PB1	*/ {   0,   0,	 0,   0,   0,	0   }, /* pin doesn't exist */
+	/* PB0	*/ {   0,   0,	 0,   0,   0,	0   }  /* pin doesn't exist */
     },
 
     /* Port C */
-    {   /*            conf ppar psor pdir podr pdat */
-	/* PC31 */ {   0,   0,   0,   1,   0,   0   }, /* PC31 */
-	/* PC30 */ {   0,   0,   0,   1,   0,   0   }, /* PC30 */
-	/* PC29 */ {   0,   1,   1,   0,   0,   0   }, /* SCC1 EN *CLSN */
-	/* PC28 */ {   0,   0,   0,   1,   0,   0   }, /* PC28 */
-	/* PC27 */ {   0,   0,   0,   1,   0,   0   }, /* UART Clock in */
-	/* PC26 */ {   0,   0,   0,   1,   0,   0   }, /* PC26 */
-	/* PC25 */ {   0,   0,   0,   1,   0,   0   }, /* PC25 */
-	/* PC24 */ {   0,   0,   0,   1,   0,   0   }, /* PC24 */
-	/* PC23 */ {   0,   1,   0,   1,   0,   0   }, /* ATMTFCLK */
-	/* PC22 */ {   0,   1,   0,   0,   0,   0   }, /* ATMRFCLK */
-	/* PC21 */ {   0,   1,   0,   0,   0,   0   }, /* SCC1 EN RXCLK */
-	/* PC20 */ {   0,   1,   0,   0,   0,   0   }, /* SCC1 EN TXCLK */
-	/* PC19 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RX_CLK CLK13 */
-	/* PC18 */ {   1,   1,   0,   0,   0,   0   }, /* FCC Tx Clock (CLK14) */
-	/* PC17 */ {   0,   0,   0,   1,   0,   0   }, /* PC17 */
-	/* PC16 */ {   0,   1,   0,   0,   0,   0   }, /* FCC Tx Clock (CLK16) */
-	/* PC15 */ {   0,   1,   0,   0,   0,   0   }, /* PC15 */
-	/* PC14 */ {   0,   1,   0,   0,   0,   0   }, /* SCC1 EN *CD */
-	/* PC13 */ {   0,   0,   0,   1,   0,   0   }, /* PC13 */
-	/* PC12 */ {   0,   1,   0,   1,   0,   0   }, /* PC12 */
-	/* PC11 */ {   0,   0,   0,   1,   0,   0   }, /* LXT971 transmit control */
-	/* PC10 */ {   0,   0,   0,   1,   0,   0   }, /* FETHMDC */
-	/* PC9  */ {   0,   0,   0,   0,   0,   0   }, /* FETHMDIO */
-	/* PC8  */ {   0,   0,   0,   1,   0,   0   }, /* PC8 */
-	/* PC7  */ {   0,   0,   0,   1,   0,   0   }, /* PC7 */
-	/* PC6  */ {   0,   0,   0,   1,   0,   0   }, /* PC6 */
-	/* PC5  */ {   0,   0,   0,   1,   0,   0   }, /* PC5 */
-	/* PC4  */ {   0,   0,   0,   1,   0,   0   }, /* PC4 */
-	/* PC3  */ {   0,   0,   0,   1,   0,   0   }, /* PC3 */
-	/* PC2  */ {   0,   0,   0,   1,   0,   1   }, /* ENET FDE */
-	/* PC1  */ {   0,   0,   0,   1,   0,   0   }, /* ENET DSQE */
-	/* PC0  */ {   0,   0,   0,   1,   0,   0   }, /* ENET LBK */
+    {	/*	      conf ppar psor pdir podr pdat */
+	/* PC31 */ {   0,   0,	 0,   1,   0,	0   }, /* PC31 */
+	/* PC30 */ {   0,   0,	 0,   1,   0,	0   }, /* PC30 */
+	/* PC29 */ {   0,   1,	 1,   0,   0,	0   }, /* SCC1 EN *CLSN */
+	/* PC28 */ {   0,   0,	 0,   1,   0,	0   }, /* PC28 */
+	/* PC27 */ {   0,   0,	 0,   1,   0,	0   }, /* UART Clock in */
+	/* PC26 */ {   0,   0,	 0,   1,   0,	0   }, /* PC26 */
+	/* PC25 */ {   0,   0,	 0,   1,   0,	0   }, /* PC25 */
+	/* PC24 */ {   0,   0,	 0,   1,   0,	0   }, /* PC24 */
+	/* PC23 */ {   0,   1,	 0,   1,   0,	0   }, /* ATMTFCLK */
+	/* PC22 */ {   0,   1,	 0,   0,   0,	0   }, /* ATMRFCLK */
+	/* PC21 */ {   0,   1,	 0,   0,   0,	0   }, /* SCC1 EN RXCLK */
+	/* PC20 */ {   0,   1,	 0,   0,   0,	0   }, /* SCC1 EN TXCLK */
+	/* PC19 */ {   1,   1,	 0,   0,   0,	0   }, /* FCC2 MII RX_CLK CLK13 */
+	/* PC18 */ {   1,   1,	 0,   0,   0,	0   }, /* FCC Tx Clock (CLK14) */
+	/* PC17 */ {   0,   0,	 0,   1,   0,	0   }, /* PC17 */
+	/* PC16 */ {   0,   1,	 0,   0,   0,	0   }, /* FCC Tx Clock (CLK16) */
+	/* PC15 */ {   0,   1,	 0,   0,   0,	0   }, /* PC15 */
+	/* PC14 */ {   0,   1,	 0,   0,   0,	0   }, /* SCC1 EN *CD */
+	/* PC13 */ {   0,   0,	 0,   1,   0,	0   }, /* PC13 */
+	/* PC12 */ {   0,   1,	 0,   1,   0,	0   }, /* PC12 */
+	/* PC11 */ {   0,   0,	 0,   1,   0,	0   }, /* LXT971 transmit control */
+	/* PC10 */ {   0,   0,	 0,   1,   0,	0   }, /* FETHMDC */
+	/* PC9	*/ {   0,   0,	 0,   0,   0,	0   }, /* FETHMDIO */
+	/* PC8	*/ {   0,   0,	 0,   1,   0,	0   }, /* PC8 */
+	/* PC7	*/ {   0,   0,	 0,   1,   0,	0   }, /* PC7 */
+	/* PC6	*/ {   0,   0,	 0,   1,   0,	0   }, /* PC6 */
+	/* PC5	*/ {   0,   0,	 0,   1,   0,	0   }, /* PC5 */
+	/* PC4	*/ {   0,   0,	 0,   1,   0,	0   }, /* PC4 */
+	/* PC3	*/ {   0,   0,	 0,   1,   0,	0   }, /* PC3 */
+	/* PC2	*/ {   0,   0,	 0,   1,   0,	1   }, /* ENET FDE */
+	/* PC1	*/ {   0,   0,	 0,   1,   0,	0   }, /* ENET DSQE */
+	/* PC0	*/ {   0,   0,	 0,   1,   0,	0   }, /* ENET LBK */
     },
 
     /* Port D */
-    {   /*            conf ppar psor pdir podr pdat */
-	/* PD31 */ {   0,   1,   0,   0,   0,   0   }, /* SCC1 EN RxD */
-	/* PD30 */ {   0,   1,   1,   1,   0,   0   }, /* SCC1 EN TxD */
-	/* PD29 */ {   0,   1,   0,   1,   0,   0   }, /* SCC1 EN TENA */
-	/* PD28 */ {   1,   1,   0,   0,   0,   0   }, /* SCC2 RxD */
-	/* PD27 */ {   1,   1,   0,   1,   0,   0   }, /* SCC2 TxD */
-	/* PD26 */ {   0,   0,   0,   1,   0,   0   }, /* PD26 */
-	/* PD25 */ {   0,   0,   0,   1,   0,   0   }, /* PD25 */
-	/* PD24 */ {   0,   0,   0,   1,   0,   0   }, /* PD24 */
-	/* PD23 */ {   0,   0,   0,   1,   0,   0   }, /* PD23 */
-	/* PD22 */ {   0,   0,   0,   1,   0,   0   }, /* PD22 */
-	/* PD21 */ {   0,   0,   0,   1,   0,   0   }, /* PD21 */
-	/* PD20 */ {   0,   0,   0,   1,   0,   0   }, /* PD20 */
-	/* PD19 */ {   0,   0,   0,   1,   0,   0   }, /* PD19 */
-	/* PD18 */ {   0,   0,   0,   1,   0,   0   }, /* PD18 */
-	/* PD17 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXPRTY */
-	/* PD16 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXPRTY */
-	/* PD15 */ {   1,   1,   1,   0,   1,   0   }, /* I2C SDA */
-	/* PD14 */ {   1,   1,   1,   0,   0,   0   }, /* I2C CLK */
-	/* PD13 */ {   0,   0,   0,   0,   0,   0   }, /* PD13 */
-	/* PD12 */ {   0,   0,   0,   0,   0,   0   }, /* PD12 */
-	/* PD11 */ {   0,   0,   0,   0,   0,   0   }, /* PD11 */
-	/* PD10 */ {   0,   0,   0,   0,   0,   0   }, /* PD10 */
-	/* PD9  */ {   0,   1,   0,   1,   0,   0   }, /* SMC1 TXD */
-	/* PD8  */ {   0,   1,   0,   0,   0,   0   }, /* SMC1 RXD */
-	/* PD7  */ {   0,   0,   0,   1,   0,   1   }, /* PD7 */
-	/* PD6  */ {   0,   0,   0,   1,   0,   1   }, /* PD6 */
-	/* PD5  */ {   0,   0,   0,   1,   0,   1   }, /* PD5 */
-	/* PD4  */ {   0,   0,   0,   1,   0,   1   }, /* PD4 */
-	/* PD3  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
-	/* PD2  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
-	/* PD1  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
-	/* PD0  */ {   0,   0,   0,   0,   0,   0   }  /* pin doesn't exist */
+    {	/*	      conf ppar psor pdir podr pdat */
+	/* PD31 */ {   0,   1,	 0,   0,   0,	0   }, /* SCC1 EN RxD */
+	/* PD30 */ {   0,   1,	 1,   1,   0,	0   }, /* SCC1 EN TxD */
+	/* PD29 */ {   0,   1,	 0,   1,   0,	0   }, /* SCC1 EN TENA */
+	/* PD28 */ {   1,   1,	 0,   0,   0,	0   }, /* SCC2 RxD */
+	/* PD27 */ {   1,   1,	 0,   1,   0,	0   }, /* SCC2 TxD */
+	/* PD26 */ {   0,   0,	 0,   1,   0,	0   }, /* PD26 */
+	/* PD25 */ {   0,   0,	 0,   1,   0,	0   }, /* PD25 */
+	/* PD24 */ {   0,   0,	 0,   1,   0,	0   }, /* PD24 */
+	/* PD23 */ {   0,   0,	 0,   1,   0,	0   }, /* PD23 */
+	/* PD22 */ {   0,   0,	 0,   1,   0,	0   }, /* PD22 */
+	/* PD21 */ {   0,   0,	 0,   1,   0,	0   }, /* PD21 */
+	/* PD20 */ {   0,   0,	 0,   1,   0,	0   }, /* PD20 */
+	/* PD19 */ {   0,   0,	 0,   1,   0,	0   }, /* PD19 */
+	/* PD18 */ {   0,   0,	 0,   1,   0,	0   }, /* PD18 */
+	/* PD17 */ {   0,   1,	 0,   0,   0,	0   }, /* FCC1 ATMRXPRTY */
+	/* PD16 */ {   0,   1,	 0,   1,   0,	0   }, /* FCC1 ATMTXPRTY */
+	/* PD15 */ {   1,   1,	 1,   0,   1,	0   }, /* I2C SDA */
+	/* PD14 */ {   1,   1,	 1,   0,   0,	0   }, /* I2C CLK */
+	/* PD13 */ {   0,   0,	 0,   0,   0,	0   }, /* PD13 */
+	/* PD12 */ {   0,   0,	 0,   0,   0,	0   }, /* PD12 */
+	/* PD11 */ {   0,   0,	 0,   0,   0,	0   }, /* PD11 */
+	/* PD10 */ {   0,   0,	 0,   0,   0,	0   }, /* PD10 */
+	/* PD9	*/ {   0,   1,	 0,   1,   0,	0   }, /* SMC1 TXD */
+	/* PD8	*/ {   0,   1,	 0,   0,   0,	0   }, /* SMC1 RXD */
+	/* PD7	*/ {   0,   0,	 0,   1,   0,	1   }, /* PD7 */
+	/* PD6	*/ {   0,   0,	 0,   1,   0,	1   }, /* PD6 */
+	/* PD5	*/ {   0,   0,	 0,   1,   0,	1   }, /* PD5 */
+	/* PD4	*/ {   0,   0,	 0,   1,   0,	1   }, /* PD4 */
+	/* PD3	*/ {   0,   0,	 0,   0,   0,	0   }, /* pin doesn't exist */
+	/* PD2	*/ {   0,   0,	 0,   0,   0,	0   }, /* pin doesn't exist */
+	/* PD1	*/ {   0,   0,	 0,   0,   0,	0   }, /* pin doesn't exist */
+	/* PD0	*/ {   0,   0,	 0,   0,   0,	0   }  /* pin doesn't exist */
     }
 };
 
@@ -227,12 +227,12 @@ reset_phy(void)
 #if (CONFIG_ETHER_INDEX == 2)
 	bcsr->bcsr2 &= ~FETH2_RST;
 	udelay(2);
-	bcsr->bcsr2 |=  FETH2_RST;
+	bcsr->bcsr2 |=	FETH2_RST;
 	udelay(1000);
 #elif (CONFIG_ETHER_INDEX == 3)
 	bcsr->bcsr3 &= ~FETH3_RST;
 	udelay(2);
-	bcsr->bcsr3 |=  FETH3_RST;
+	bcsr->bcsr3 |=	FETH3_RST;
 	udelay(1000);
 #endif
 #if defined(CONFIG_MII) && defined(CONFIG_ETHER_ON_FCC)
@@ -252,10 +252,10 @@ int
 board_early_init_f(void)
 {
 #if defined(CONFIG_PCI)
-    volatile immap_t *immr = (immap_t *)CFG_IMMR;
-    volatile ccsr_pcix_t *pci = &immr->im_pcix;
+	volatile immap_t *immr = (immap_t *)CFG_IMMR;
+	volatile ccsr_pcix_t *pci = &immr->im_pcix;
 
-    pci->peer &= 0xfffffffdf; /* disable master abort */
+	pci->peer &= 0xffffffdf; /* disable master abort */
 #endif
 
 	/* Why is the phy reset done _after_ the ethernet
diff --git a/board/tqm5200/tqm5200.c b/board/tqm5200/tqm5200.c
index a4322b6661..cf97603afc 100644
--- a/board/tqm5200/tqm5200.c
+++ b/board/tqm5200/tqm5200.c
@@ -32,6 +32,10 @@
 #include <pci.h>
 #include <asm/processor.h>
 
+#if defined(CONFIG_OF_FLAT_TREE)
+#include <ft_build.h>
+#endif
+
 #ifdef CONFIG_VIDEO_SM501
 #include <sm501.h>
 #endif
@@ -775,3 +779,10 @@ int board_get_height (void)
 }
 
 #endif /* CONFIG_VIDEO_SM501 */
+
+#if defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+	ft_cpu_setup(blob, bd);
+}
+#endif /* defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP) */
diff --git a/board/xpedite1k/xpedite1k.c b/board/xpedite1k/xpedite1k.c
index a569b53472..8411cf06f7 100644
--- a/board/xpedite1k/xpedite1k.c
+++ b/board/xpedite1k/xpedite1k.c
@@ -209,7 +209,7 @@ long int fixed_sdram (void)
  *	certain pre-initialization actions.
  *
  ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT)
+#if defined(CONFIG_PCI)
 int pci_pre_init(struct pci_controller * hose )
 {
 	unsigned long strap;
@@ -227,7 +227,7 @@ int pci_pre_init(struct pci_controller * hose )
 #endif
 	return 1;
 }
-#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */
+#endif /* defined(CONFIG_PCI) */
 
 /*************************************************************************
  *  pci_target_init