Merge branch 'master' of http://www.denx.de/git/u-boot

5 files changed, 422 insertions, 12 deletions

diff --git a/include/configs/CPCI750.h b/include/configs/CPCI750.h
index 150e5267f2..1632f374c3 100644
--- a/include/configs/CPCI750.h
+++ b/include/configs/CPCI750.h
@@ -285,13 +285,19 @@
  * FLASH related
  *----------------------------------------------------------------------*/
 
+#define CFG_FLASH_CFI_DRIVER
 #define CFG_FLASH_CFI		1	   /* Flash is CFI conformant		*/
-#define CFG_MAX_FLASH_SECT	128	   /* max number of sectors on one chip	*/
-#define CFG_MAX_FLASH_BANKS	4	   /* max number of memory banks	*/
-#define CFG_FLASH_INCREMENT	0x01000000 /* there is only one bank		*/
 #define CFG_FLASH_PROTECTION	1	   /* use hardware protection		*/
 #define CFG_FLASH_USE_BUFFER_WRITE 1	   /* use buffered writes (20x faster)	*/
 #define CFG_FLASH_BASE		0xfc000000 /* start of flash banks              */
+#define CFG_MAX_FLASH_BANKS	4	   /* max number of memory banks	*/
+#define CFG_FLASH_INCREMENT     0x01000000 /* size of  flash bank               */
+#define CFG_MAX_FLASH_SECT	128	   /* max number of sectors on one chip	*/
+#define CFG_FLASH_BANKS_LIST  { CFG_FLASH_BASE,                            \
+                                CFG_FLASH_BASE + 1*CFG_FLASH_INCREMENT,    \
+                                CFG_FLASH_BASE + 2*CFG_FLASH_INCREMENT,    \
+                                CFG_FLASH_BASE + 3*CFG_FLASH_INCREMENT }
+#define CFG_FLASH_EMPTY_INFO    1          /* show if bank is empty             */
 
 /* areas to map different things with the GT in physical space */
 #define CFG_DRAM_BANKS		4
diff --git a/include/configs/HH405.h b/include/configs/HH405.h
index 131c21555d..4f62b8ae8a 100644
--- a/include/configs/HH405.h
+++ b/include/configs/HH405.h
@@ -5,6 +5,9 @@
  * (C) Copyright 2005
  * Stefan Roese, DENX Software Engineering, sr@denx.de.
  *
+ * (C) Copyright 2006
+ * Matthias Fuchs, esd GmbH, matthias.fuchs@esd-electronics.com
+ *
  * See file CREDITS for list of people who contributed to this
  * project.
  *
@@ -61,9 +64,13 @@
 
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
+#define CONFIG_NET_MULTI	1
+#undef  CONFIG_HAS_ETH1
+
 #define CONFIG_MII		1	/* MII PHY management		*/
-#define	CONFIG_PHY_ADDR		0	/* PHY address			*/
+#define CONFIG_PHY_ADDR		0	/* PHY address			*/
 #define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
+#define CONFIG_RESET_PHY_R      1       /* use reset_phy() to disable phy sleep mode */
 
 #define CONFIG_PHY_CLK_FREQ	EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
 
@@ -79,6 +86,7 @@
 #else
 #define CONFIG_VIDEO_SM501_16BPP
 #endif
+#define CONFIG_VIDEO_SM501_FBMEM_OFFSET 0x10000
 #define CONFIG_CFB_CONSOLE
 #define CONFIG_VIDEO_LOGO
 #define CONFIG_VGA_AS_SINGLE_DEVICE
@@ -434,9 +442,12 @@
 #define CFG_FPGA_CTRL_VGA0_BL_MODE 0x0008
 #define CFG_FPGA_CTRL_CF_RESET  0x0040
 #define CFG_FPGA_CTRL_PS2_PWR   0x0080
-#define CFG_FPGA_CTRL_CF_PWR    0x0100      /* low active                    */
+#define CFG_FPGA_CTRL_CF_PWRN   0x0100      /* low active                    */
 #define CFG_FPGA_CTRL_CF_BUS_EN 0x0200
 #define CFG_FPGA_CTRL_LCD_CLK   0x7000      /* Mask for lcd clock            */
+#define CFG_FPGA_CTRL_OW_ENABLE 0x8000
+
+#define CFG_FPGA_STATUS_CF_DETECT 0x8000
 
 #define LCD_CLK_OFF             0x0000      /* Off                           */
 #define LCD_CLK_02083           0x1000      /* 2.083 MHz                     */
diff --git a/include/configs/inka4x0.h b/include/configs/inka4x0.h
index c0cc4f1fbe..773d5d2c1d 100644
--- a/include/configs/inka4x0.h
+++ b/include/configs/inka4x0.h
@@ -101,7 +101,7 @@
 /*
  * Autobooting
  */
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds */
+#define CONFIG_BOOTDELAY	1	/* autoboot after 1 second */
 
 #define CONFIG_PREBOOT	"echo;" \
 	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
@@ -109,6 +109,16 @@
 
 #undef	CONFIG_BOOTARGS
 
+#define	CONFIG_ETHADDR		00:a0:a4:03:00:00
+#define	CONFIG_OVERWRITE_ETHADDR_ONCE
+
+#define	CONFIG_IPADDR		192.168.100.2
+#define	CONFIG_SERVERIP		192.168.100.1
+#define	CONFIG_NETMASK		255.255.255.0
+#define HOSTNAME		inka4x0
+#define CONFIG_BOOTFILE		/tftpboot/inka4x0/uImage
+#define	CONFIG_ROOTPATH		/opt/eldk/ppc_6xx
+
 #define CONFIG_EXTRA_ENV_SETTINGS					\
 	"netdev=eth0\0"							\
 	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
@@ -117,13 +127,22 @@
 	"addip=setenv bootargs ${bootargs} "				\
 		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
 		":${hostname}:${netdev}:off panic=1\0"			\
-	"flash_nfs=run nfsargs addip;"					\
+	"addcons=setenv bootargs ${bootargs} "				\
+		"console=ttyS0,${baudrate}\0"				\
+	"flash_nfs=run nfsargs addip addcons;"				\
 		"bootm ${kernel_addr}\0"				\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
-	"rootpath=/opt/eldk/ppc_82xx\0"					\
+	"net_nfs=tftp 200000 ${bootfile};"				\
+		"run nfsargs addip addcons;bootm\0"			\
+	"enable_disp=mw.l 100000 04000000 1;"				\
+		"cp.l 100000 f0000b20 1;"				\
+		"cp.l 100000 f0000b28 1\0"				\
+	"ideargs=setenv bootargs root=/dev/hda1 rw\0"			\
+	"ide_boot=ext2load ide 0:1 200000 uImage;"			\
+		"run ideargs addip addcons enable_disp;bootm"		\
+	"brightness=255\0"						\
 	""
 
-#define CONFIG_BOOTCOMMAND	"run net_nfs"
+#define CONFIG_BOOTCOMMAND	"run ide_boot"
 
 /*
  * IPB Bus clocking configuration.
@@ -193,6 +212,7 @@
  */
 /* #define CONFIG_FEC_10MBIT 1 */
 #define CONFIG_PHY_ADDR		0x00
+#define CONFIG_MII
 
 /*
  * GPIO configuration
diff --git a/include/configs/smmaco4.h b/include/configs/smmaco4.h
new file mode 100644
index 0000000000..e106b3b574
--- /dev/null
+++ b/include/configs/smmaco4.h
@@ -0,0 +1,373 @@
+/*
+ * (C) Copyright 2003-2006
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * (C) Copyright 2004-2005
+ * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC5xxx		1	/* This is an MPC5xxx CPU */
+#define CONFIG_MPC5200		1	/* (more precisely an MPC5200 CPU) */
+#define CONFIG_TQM5200		1	/* ... on TQM5200 module */
+#undef CONFIG_TQM5200_REV100		/*  define for revision 100 modules */
+
+#define CFG_MPC5XXX_CLKIN	33000000 /* ... running at 33.000000MHz */
+
+#define BOOTFLAG_COLD		0x01	/* Normal Power-On: Boot from FLASH  */
+#define BOOTFLAG_WARM		0x02	/* Software reboot	     */
+
+#define CFG_CACHELINE_SIZE	32	/* For MPC5xxx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#  define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
+#endif
+
+/*
+ * Serial console configuration
+ */
+#define CONFIG_PSC_CONSOLE	1	/* console is on PSC1 */
+#define CONFIG_BAUDRATE		115200	/* ... at 115200 bps */
+#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
+
+/* Partitions */
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+
+/* POST support */
+#define CONFIG_POST		(CFG_POST_MEMORY   | \
+				 CFG_POST_CPU	   | \
+				 CFG_POST_I2C)
+
+#ifdef CONFIG_POST
+#define CFG_CMD_POST_DIAG CFG_CMD_DIAG
+/* preserve space for the post_word at end of on-chip SRAM */
+#define MPC5XXX_SRAM_POST_SIZE MPC5XXX_SRAM_SIZE-4
+#else
+#define CFG_CMD_POST_DIAG 0
+#endif
+
+/*
+ * Supported commands
+ */
+#define CONFIG_COMMANDS	       (CONFIG_CMD_DFL	| \
+				CFG_CMD_ASKENV	| \
+				CFG_CMD_DATE	| \
+				CFG_CMD_DHCP	| \
+				CFG_CMD_ECHO	| \
+				CFG_CMD_EEPROM	| \
+				CFG_CMD_I2C	| \
+				CFG_CMD_JFFS2	| \
+				CFG_CMD_MII	| \
+				CFG_CMD_NFS	| \
+				CFG_CMD_PING	| \
+				CFG_CMD_POST_DIAG | \
+				CFG_CMD_REGINFO | \
+				CFG_CMD_SNTP	)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#define	CONFIG_TIMESTAMP		/* display image timestamps */
+
+#if (TEXT_BASE == 0xFC000000)		/* Boot low */
+#   define CFG_LOWBOOT		1
+#endif
+
+/*
+ * Autobooting
+ */
+#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds */
+
+#define CONFIG_PREBOOT	"echo;" \
+	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+	"echo"
+
+#undef	CONFIG_BOOTARGS
+
+#define CONFIG_EXTRA_ENV_SETTINGS					\
+	"netdev=eth0\0"							\
+	"rootpath=/opt/eldk/ppc_6xx\0"					\
+	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+		"nfsroot=${serverip}:${rootpath}\0"			\
+	"addip=setenv bootargs ${bootargs} "				\
+		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
+		":${hostname}:${netdev}:off panic=1\0"			\
+	"flash_self=run ramargs addip;"					\
+		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
+	"flash_nfs=run nfsargs addip;"					\
+		"bootm ${kernel_addr}\0"				\
+	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
+	"bootfile=/tftpboot/smmaco4/uImage\0"				\
+	"load=tftp 200000 ${u-boot}\0"					\
+	"u-boot=/tftpboot/smmaco4/u-boot.bin\0"				\
+	"update=protect off FC000000 FC05FFFF;"				\
+		"erase FC000000 FC05FFFF;"				\
+		"cp.b 200000 FC000000 ${filesize};"			\
+		"protect on FC000000 FC05FFFF\0"			\
+	""
+
+#define CONFIG_BOOTCOMMAND	"run net_nfs"
+
+/*
+ * IPB Bus clocking configuration.
+ */
+#define CFG_IPBSPEED_133		/* define for 133MHz speed */
+
+#if defined(CFG_IPBSPEED_133)
+/*
+ * PCI Bus clocking configuration
+ *
+ * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
+ * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't
+ * been tested with a IPB Bus Clock of 66 MHz.
+ */
+#define CFG_PCISPEED_66			/* define for 66MHz speed */
+#endif
+
+/*
+ * I2C configuration
+ */
+#define CONFIG_HARD_I2C		1	/* I2C with hardware support */
+#ifdef CONFIG_TQM5200_REV100
+#define CFG_I2C_MODULE		1	/* Select I2C module #1 for rev. 100 board */
+#else
+#define CFG_I2C_MODULE		2	/* Select I2C module #2 for all other revs */
+#endif
+
+/*
+ * I2C clock frequency
+ *
+ * Please notice, that the resulting clock frequency could differ from the
+ * configured value. This is because the I2C clock is derived from system
+ * clock over a frequency divider with only a few divider values. U-boot
+ * calculates the best approximation for CFG_I2C_SPEED. However the calculated
+ * approximation allways lies below the configured value, never above.
+ */
+#define CFG_I2C_SPEED		100000 /* 100 kHz */
+#define CFG_I2C_SLAVE		0x7F
+
+/*
+ * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work
+ * also). For other EEPROMs configuration should be verified. On Mini-FAP the
+ * EEPROM (24C64) is on the same I2C address (but on other I2C bus), so the
+ * same configuration could be used.
+ */
+#define CFG_I2C_EEPROM_ADDR		0x50	/* 1010000x */
+#define CFG_I2C_EEPROM_ADDR_LEN		2
+#define CFG_EEPROM_PAGE_WRITE_BITS	5	/* =32 Bytes per write */
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	20
+
+/*
+ * Flash configuration
+ */
+#define CFG_FLASH_BASE		TEXT_BASE /* 0xFC000000 */
+
+/* use CFI flash driver if no module variant is spezified */
+#define CFG_FLASH_CFI		1	/* Flash is CFI conformant */
+#define CFG_FLASH_CFI_DRIVER	1	/* Use the common driver */
+#define CFG_FLASH_BANKS_LIST	{ CFG_BOOTCS_START }
+#define CFG_FLASH_EMPTY_INFO
+#define CFG_FLASH_SIZE		0x04000000 /* 64 MByte */
+#define CFG_MAX_FLASH_SECT	512	/* max num of sects on one chip */
+#undef CFG_FLASH_USE_BUFFER_WRITE	/* not supported yet for AMD */
+
+#if !defined(CFG_LOWBOOT)
+#define CFG_ENV_ADDR		(CFG_FLASH_BASE + 0x00760000 + 0x00800000)
+#else	/* CFG_LOWBOOT */
+#define CFG_ENV_ADDR		(CFG_FLASH_BASE + 0x00060000)
+#endif	/* CFG_LOWBOOT */
+#define CFG_MAX_FLASH_BANKS	1	/* max num of flash banks
+					   (= chip selects) */
+#define CFG_FLASH_ERASE_TOUT	240000	/* Flash Erase Timeout (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)	*/
+
+/* Dynamic MTD partition support */
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT		"nor0=TQM5200-0"
+#define MTDPARTS_DEFAULT	"mtdparts=TQM5200-0:640k(firmware),"	\
+						"1408k(kernel),"	\
+						"2m(initrd),"		\
+						"4m(small-fs),"		\
+						"16m(big-fs),"		\
+						"8m(misc)"
+
+/*
+ * Environment settings
+ */
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_SIZE		0x10000
+#define CFG_ENV_SECT_SIZE	0x20000
+#define CFG_ENV_ADDR_REDUND	(CFG_ENV_ADDR + CFG_ENV_SECT_SIZE)
+#define	CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
+
+/*
+ * Memory map
+ */
+#define CFG_MBAR		0xF0000000
+#define CFG_SDRAM_BASE		0x00000000
+#define CFG_DEFAULT_MBAR	0x80000000
+
+/* Use ON-Chip SRAM until RAM will be available */
+#define CFG_INIT_RAM_ADDR	MPC5XXX_SRAM
+#ifdef CONFIG_POST
+/* preserve space for the post_word at end of on-chip SRAM */
+#define CFG_INIT_RAM_END	MPC5XXX_SRAM_POST_SIZE
+#else
+#define CFG_INIT_RAM_END	MPC5XXX_SRAM_SIZE
+#endif
+
+
+#define CFG_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_BASE	TEXT_BASE
+#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
+#   define CFG_RAMBOOT		1
+#endif
+
+#define CFG_MONITOR_LEN		(384 << 10)	/* Reserve 384 kB for Monitor	*/
+#define CFG_MALLOC_LEN		(256 << 10)	/* Reserve 256 kB for malloc()	*/
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+
+/*
+ * Ethernet configuration
+ */
+#define CONFIG_MPC5xxx_FEC	1
+/*
+ * Define CONFIG_FEC_10MBIT to force FEC at 10Mb
+ */
+/* #define CONFIG_FEC_10MBIT 1 */
+#define CONFIG_PHY_ADDR		0x00
+
+/*
+ * GPIO configuration
+ *
+ * use pin gpio_wkup_6 as second SDRAM chip select (mem_cs1):
+ *	Bit 0 (mask: 0x80000000): 1
+ * use ALT CAN position: Bits 2-3 (mask: 0x30000000):
+ *	00 -> No Alternatives, CAN1/2 on PSC2 according to PSC2 setting.
+ *	01 -> CAN1 on I2C1, CAN2 on Tmr0/1.
+ *	      Use for REV200 STK52XX boards. Do not use with REV100 modules
+ *	      (because, there I2C1 is used as I2C bus)
+ * use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100
+ * use PSC2 as CAN: Bits 25:27 (mask: 0x00000030)
+ *	000 -> All PSC2 pins are GIOPs
+ *	001 -> CAN1/2 on PSC2 pins
+ *	       Use for REV100 STK52xx boards
+ * use PSC6:
+ *   on STK52xx:
+ *	use as UART. Pins PSC6_0 to PSC6_3 are used.
+ *	Bits 9:11 (mask: 0x00700000):
+ *	   101 -> PSC6 : Extended POST test is not available
+ *   on MINI-FAP and TQM5200_IB:
+ *	use PSC6_0 to PSC6_3 as GPIO: Bits 9:11 (mask: 0x00700000):
+ *	   000 -> PSC6 could not be used as UART, CODEC or IrDA
+ *   GPIO on PSC6_3 is used in post_hotkeys_pressed() to enable extended POST
+ *   tests.
+ */
+#if defined (CONFIG_MINIFAP)
+# define CFG_GPS_PORT_CONFIG	0x91000004
+#elif defined (CONFIG_STK52XX)
+# if defined (CONFIG_STK52XX_REV100)
+#  define CFG_GPS_PORT_CONFIG	0x81500014
+# else /* STK52xx REV200 and above */
+#  if defined (CONFIG_TQM5200_REV100)
+#   error TQM5200 REV100 not supported on STK52XX REV200 or above
+#  else/* TQM5200 REV200 and above */
+#   define CFG_GPS_PORT_CONFIG	0x91500004
+#  endif
+# endif
+#else  /* TMQ5200 Inbetriebnahme-Board */
+# define CFG_GPS_PORT_CONFIG	0x81000004
+#endif
+
+/*
+ * RTC configuration
+ */
+#define CONFIG_RTC_MPC5200	1	/* use internal MPC5200 RTC */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory	    */
+#define CFG_PROMPT		"=> "	/* Monitor Command Prompt   */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE		1024	/* Console I/O Buffer Size  */
+#else
+#define CFG_CBSIZE		256	/* Console I/O Buffer Size  */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS		16	/* max number of command args	*/
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+/* Enable an alternate, more extensive memory test */
+#define CFG_ALT_MEMTEST
+
+#define CFG_MEMTEST_START	0x00100000	/* memtest works on */
+#define CFG_MEMTEST_END		0x00f00000	/* 1 ... 15 MB in DRAM	*/
+
+#define CFG_LOAD_ADDR		0x100000	/* default load address */
+
+#define CFG_HZ			1000	/* decrementer freq: 1 ms ticks */
+
+/*
+ * Enable loopw commando. This has only affect, if CFG_CMD_MEM is defined,
+ * which is normally part of the default commands (CFV_CMD_DFL)
+ */
+#define CONFIG_LOOPW
+
+/*
+ * Various low-level settings
+ */
+#if defined(CONFIG_MPC5200)
+#define CFG_HID0_INIT		HID0_ICE | HID0_ICFI
+#define CFG_HID0_FINAL		HID0_ICE
+#else
+#define CFG_HID0_INIT		0
+#define CFG_HID0_FINAL		0
+#endif
+
+#define CFG_BOOTCS_START	CFG_FLASH_BASE
+#define CFG_BOOTCS_SIZE		CFG_FLASH_SIZE
+#ifdef CFG_PCISPEED_66
+#define CFG_BOOTCS_CFG		0x0008DF30 /* for pci_clk  = 66 MHz */
+#else
+#define CFG_BOOTCS_CFG		0x0004DF30 /* for pci_clk = 33 MHz */
+#endif
+#define CFG_CS0_START		CFG_FLASH_BASE
+#define CFG_CS0_SIZE		CFG_FLASH_SIZE
+
+#define CFG_CS_BURST		0x00000000
+#define CFG_CS_DEADCYCLE	0x33333311	/* 1 dead cycle for flash and SM501 */
+
+#define CFG_RESET_ADDRESS	0xff000000
+
+#endif /* __CONFIG_H */
diff --git a/include/version.h b/include/version.h
index 4f8b498cf3..b56d2e9900 100644
--- a/include/version.h
+++ b/include/version.h
@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2000-2003
+ * (C) Copyright 2000-2006
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
@@ -24,6 +24,6 @@
 #ifndef	__VERSION_H__
 #define	__VERSION_H__
 
-#define	U_BOOT_VERSION	"U-Boot 1.1.4"
+#include "version_autogenerated.h"
 
 #endif	/* __VERSION_H__ */