diff options
Diffstat (limited to 'arch/arm/cpu/armv7/start.S')
-rw-r--r-- | arch/arm/cpu/armv7/start.S | 113 |
1 files changed, 0 insertions, 113 deletions
diff --git a/arch/arm/cpu/armv7/start.S b/arch/arm/cpu/armv7/start.S index bdf2fad380..4a0710c96d 100644 --- a/arch/arm/cpu/armv7/start.S +++ b/arch/arm/cpu/armv7/start.S @@ -70,12 +70,6 @@ _end_vect: _TEXT_BASE: .word CONFIG_SYS_TEXT_BASE -#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC) -.globl _armboot_start -_armboot_start: - .word _start -#endif - /* * These are defined in the board-specific linker script. */ @@ -99,7 +93,6 @@ FIQ_STACK_START: .word 0x0badc0de #endif -#if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) /* IRQ stack memory (calculated at run-time) + 8 bytes */ .globl IRQ_STACK_START_IN IRQ_STACK_START_IN: @@ -295,94 +288,6 @@ _rel_dyn_end_ofs: _dynsym_start_ofs: .word __dynsym_start - _start -#else /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */ -/* - * the actual reset code - */ - -reset: - /* - * set the cpu to SVC32 mode - */ - mrs r0, cpsr - bic r0, r0, #0x1f - orr r0, r0, #0xd3 - msr cpsr,r0 - -#if (CONFIG_OMAP34XX) - /* Copy vectors to mask ROM indirect addr */ - adr r0, _start @ r0 <- current position of code - add r0, r0, #4 @ skip reset vector - mov r2, #64 @ r2 <- size to copy - add r2, r0, r2 @ r2 <- source end address - mov r1, #SRAM_OFFSET0 @ build vect addr - mov r3, #SRAM_OFFSET1 - add r1, r1, r3 - mov r3, #SRAM_OFFSET2 - add r1, r1, r3 -next: - ldmia r0!, {r3 - r10} @ copy from source address [r0] - stmia r1!, {r3 - r10} @ copy to target address [r1] - cmp r0, r2 @ until source end address [r2] - bne next @ loop until equal */ -#if !defined(CONFIG_SYS_NAND_BOOT) && !defined(CONFIG_SYS_ONENAND_BOOT) - /* No need to copy/exec the clock code - DPLL adjust already done - * in NAND/oneNAND Boot. - */ - bl cpy_clk_code @ put dpll adjust code behind vectors -#endif /* NAND Boot */ -#endif - /* the mask ROM code should have PLL and others stable */ -#ifndef CONFIG_SKIP_LOWLEVEL_INIT - bl cpu_init_crit -#endif - -#ifndef CONFIG_SKIP_RELOCATE_UBOOT -relocate: @ relocate U-Boot to RAM - adr r0, _start @ r0 <- current position of code - ldr r1, _TEXT_BASE @ test if we run from flash or RAM - cmp r0, r1 @ don't reloc during debug - beq stack_setup - - ldr r2, _armboot_start - ldr r3, _bss_start - sub r2, r3, r2 @ r2 <- size of armboot - add r2, r0, r2 @ r2 <- source end address - -copy_loop: @ copy 32 bytes at a time - ldmia r0!, {r3 - r10} @ copy from source address [r0] - stmia r1!, {r3 - r10} @ copy to target address [r1] - cmp r0, r2 @ until source end address [r2] - blo copy_loop -#endif /* CONFIG_SKIP_RELOCATE_UBOOT */ - - /* Set up the stack */ -stack_setup: - ldr r0, _TEXT_BASE @ upper 128 KiB: relocated uboot - sub r0, r0, #CONFIG_SYS_MALLOC_LEN @ malloc area - sub r0, r0, #GENERATED_GBL_DATA_SIZE @ bdinfo -#ifdef CONFIG_USE_IRQ - sub r0, r0, #(CONFIG_STACKSIZE_IRQ + CONFIG_STACKSIZE_FIQ) -#endif - sub sp, r0, #12 @ leave 3 words for abort-stack - bic sp, sp, #7 @ 8-byte alignment for ABI compliance - - /* Clear BSS (if any). Is below tx (watch load addr - need space) */ -clear_bss: - ldr r0, _bss_start @ find start of bss segment - ldr r1, _bss_end @ stop here - mov r2, #0x00000000 @ clear value -clbss_l: - str r2, [r0] @ clear BSS location - cmp r0, r1 @ are we at the end yet - add r0, r0, #4 @ increment clear index pointer - bne clbss_l @ keep clearing till at end - - ldr pc, _start_armboot @ jump to C code - -_start_armboot: .word start_armboot -#endif /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */ - /************************************************************************* * * CPU_init_critical registers @@ -464,14 +369,8 @@ cpu_init_crit: @ user stack stmia sp, {r0 - r12} @ Save user registers (now in @ svc mode) r0-r12 -#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC) - ldr r2, _armboot_start - sub r2, r2, #(CONFIG_SYS_MALLOC_LEN) - sub r2, r2, #(GENERATED_GBL_DATA_SIZE + 8) @ set base 2 words into abort -#else ldr r2, IRQ_STACK_START_IN @ set base 2 words into abort @ stack -#endif ldmia r2, {r2 - r3} @ get values for "aborted" pc @ and cpsr (into parm regs) add r0, sp, #S_FRAME_SIZE @ grab pointer to old stack @@ -507,14 +406,8 @@ cpu_init_crit: .endm .macro get_bad_stack -#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC) - ldr r13, _armboot_start @ setup our mode stack (enter - sub r13, r13, #(CONFIG_SYS_MALLOC_LEN) @ move past malloc pool - sub r13, r13, #(GENERATED_GBL_DATA_SIZE + 8) @ move to reserved a couple -#else ldr r13, IRQ_STACK_START_IN @ setup our mode stack (enter @ in banked mode) -#endif str lr, [r13] @ save caller lr in position 0 @ of saved stack @@ -535,14 +428,8 @@ cpu_init_crit: sub r13, r13, #4 @ space on current stack for @ scratch reg. str r0, [r13] @ save R0's value. -#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC) - ldr r0, _armboot_start @ get data regions start - sub r0, r0, #(CONFIG_SYS_MALLOC_LEN) @ move past malloc pool - sub r0, r0, #(GENERATED_GBL_DATA_SIZE + 8) @ move past gbl and a couple -#else ldr r0, IRQ_STACK_START_IN @ get data regions start @ spots for abort stack -#endif str lr, [r0] @ save caller lr in position 0 @ of saved stack mrs r0, spsr @ get the spsr |