summaryrefslogtreecommitdiff
path: root/arch/arm/cpu
diff options
context:
space:
mode:
Diffstat (limited to 'arch/arm/cpu')
-rw-r--r--arch/arm/cpu/arm1136/start.S127
-rw-r--r--arch/arm/cpu/arm1176/start.S214
-rw-r--r--arch/arm/cpu/arm720t/start.S105
-rw-r--r--arch/arm/cpu/arm920t/start.S144
-rw-r--r--arch/arm/cpu/arm925t/start.S121
-rw-r--r--arch/arm/cpu/arm926ejs/orion5x/dram.c15
-rw-r--r--arch/arm/cpu/arm926ejs/start.S96
-rw-r--r--arch/arm/cpu/arm946es/start.S85
-rw-r--r--arch/arm/cpu/arm_intcm/start.S87
-rw-r--r--arch/arm/cpu/armv7/omap3/emif4.c24
-rw-r--r--arch/arm/cpu/armv7/omap3/sdrc.c28
-rw-r--r--arch/arm/cpu/armv7/omap4/board.c5
-rw-r--r--arch/arm/cpu/armv7/start.S113
-rw-r--r--arch/arm/cpu/ixp/start.S203
-rw-r--r--arch/arm/cpu/lh7a40x/start.S113
-rw-r--r--arch/arm/cpu/pxa/start.S28
-rw-r--r--arch/arm/cpu/s3c44b0/start.S85
-rw-r--r--arch/arm/cpu/sa1100/start.S88
18 files changed, 8 insertions, 1673 deletions
diff --git a/arch/arm/cpu/arm1136/start.S b/arch/arm/cpu/arm1136/start.S
index d70ca1d515..9f172b625d 100644
--- a/arch/arm/cpu/arm1136/start.S
+++ b/arch/arm/cpu/arm1136/start.S
@@ -132,14 +132,11 @@ FIQ_STACK_START:
.word 0x0badc0de
#endif
-#if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
/* IRQ stack memory (calculated at run-time) + 8 bytes */
.globl IRQ_STACK_START_IN
IRQ_STACK_START_IN:
.word 0x0badc0de
-#endif
-#if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
/*
* the actual reset code
*/
@@ -318,112 +315,6 @@ _rel_dyn_end_ofs:
_dynsym_start_ofs:
.word __dynsym_start - _start
-#else /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
-/*
- * the actual reset code
- */
-
-reset:
- /*
- * set the cpu to SVC32 mode
- */
- mrs r0,cpsr
- bic r0,r0,#0x1f
- orr r0,r0,#0xd3
- msr cpsr,r0
-
-#ifdef CONFIG_OMAP2420H4
- /* Copy vectors to mask ROM indirect addr */
- adr r0, _start /* r0 <- current position of code */
- add r0, r0, #4 /* skip reset vector */
- mov r2, #64 /* r2 <- size to copy */
- add r2, r0, r2 /* r2 <- source end address */
- mov r1, #SRAM_OFFSET0 /* build vect addr */
- mov r3, #SRAM_OFFSET1
- add r1, r1, r3
- mov r3, #SRAM_OFFSET2
- add r1, r1, r3
-next:
- ldmia r0!, {r3-r10} /* copy from source address [r0] */
- stmia r1!, {r3-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- bne next /* loop until equal */
- bl cpy_clk_code /* put dpll adjust code behind vectors */
-#endif
- /* the mask ROM code should have PLL and others stable */
-#ifndef CONFIG_SKIP_LOWLEVEL_INIT
- bl cpu_init_crit
-#endif
-
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
-relocate: /* relocate U-Boot to RAM */
- adr r0, _start /* r0 <- current position of code */
- ldr r1, _TEXT_BASE /* test if we run from flash or RAM */
- cmp r0, r1 /* don't reloc during debug */
-#ifndef CONFIG_PRELOADER
- beq stack_setup
-#endif /* CONFIG_PRELOADER */
-
- ldr r2, _armboot_start
- ldr r3, _bss_start
- sub r2, r3, r2 /* r2 <- size of armboot */
- add r2, r0, r2 /* r2 <- source end address */
-
-copy_loop:
- ldmia r0!, {r3-r10} /* copy from source address [r0] */
- stmia r1!, {r3-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- blo copy_loop
-#endif /* CONFIG_SKIP_RELOCATE_UBOOT */
-
- /* Set up the stack */
-stack_setup:
- ldr r0, _TEXT_BASE /* upper 128 KiB: relocated uboot */
-#ifdef CONFIG_PRELOADER
- sub sp, r0, #128 /* leave 32 words for abort-stack */
-#else
- sub r0, r0, #CONFIG_SYS_MALLOC_LEN /* malloc area */
- sub r0, r0, #GENERATED_GBL_DATA_SIZE /* bdinfo */
-#ifdef CONFIG_USE_IRQ
- sub r0, r0, #(CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ)
-#endif
- sub sp, r0, #12 /* leave 3 words for abort-stack */
-#endif /* CONFIG_PRELOADER */
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
-
-clear_bss:
- adr r2, _start
- ldr r0, _bss_start_ofs /* find start of bss segment */
- add r0, r0, r2
- ldr r1, _bss_end_ofs /* stop here */
- add r1, r1, r2
- mov r2, #0x00000000 /* clear */
-
-#ifndef CONFIG_PRELOADER
-clbss_l:str r2, [r0] /* clear loop... */
- add r0, r0, #4
- cmp r0, r1
- bne clbss_l
-#endif
-
- ldr r0, _start_armboot_ofs
- adr r1, _start
- add r0, r0, r1
- ldr pc, r0
-
-_start_armboot_ofs:
-#ifdef CONFIG_NAND_SPL
- .word nand_boot - _start
-#else
-#ifdef CONFIG_ONENAND_IPL
- .word start_oneboot - _start
-#else
- .word start_armboot - _start
-#endif /* CONFIG_ONENAND_IPL */
-#endif /* CONFIG_NAND_SPL */
-
-#endif /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
-
/*
*************************************************************************
*
@@ -508,13 +399,7 @@ cpu_init_crit:
sub sp, sp, #S_FRAME_SIZE @ carve out a frame on current user stack
stmia sp, {r0 - r12} @ Save user registers (now in svc mode) r0-r12
-#if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
ldr r2, IRQ_STACK_START_IN @ set base 2 words into abort stack
-#else
- adr r2, _start
- sub r2, r2, #(CONFIG_SYS_MALLOC_LEN)
- sub r2, r2, #(GENERATED_GBL_DATA_SIZE+8) @ set base 2 words into abort stack
-#endif
ldmia r2, {r2 - r3} @ get values for "aborted" pc and cpsr (into parm regs)
add r0, sp, #S_FRAME_SIZE @ grab pointer to old stack
@@ -545,13 +430,7 @@ cpu_init_crit:
.endm
.macro get_bad_stack
-#if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
ldr r13, IRQ_STACK_START_IN @ setup our mode stack (enter in banked mode)
-#else
- adr r13, _start @ setup our mode stack (enter in banked mode)
- sub r13, r13, #(CONFIG_STACKSIZE+CONFIG_SYS_MALLOC_LEN) @ move past malloc pool
- sub r13, r13, #(GENERATED_GBL_DATA_SIZE+8) @ move to reserved a couple spots for abort stack
-#endif
str lr, [r13] @ save caller lr in position 0 of saved stack
mrs lr, spsr @ get the spsr
@@ -567,13 +446,7 @@ cpu_init_crit:
.macro get_bad_stack_swi
sub r13, r13, #4 @ space on current stack for scratch reg.
str r0, [r13] @ save R0's value.
-#if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
ldr r0, IRQ_STACK_START_IN @ get data regions start
-#else
- ldr r0, _armboot_start @ get data regions start
- sub r0, r0, #(CONFIG_SYS_MALLOC_LEN) @ move past malloc pool
- sub r0, r0, #(GENERATED_GBL_DATA_SIZE+8) @ move past gbl and a couple spots for abort stack
-#endif
str lr, [r0] @ save caller lr in position 0 of saved stack
mrs r0, spsr @ get the spsr
str lr, [r0, #4] @ save spsr in position 1 of saved stack
diff --git a/arch/arm/cpu/arm1176/start.S b/arch/arm/cpu/arm1176/start.S
index 7f32db7874..1a2e5aa37e 100644
--- a/arch/arm/cpu/arm1176/start.S
+++ b/arch/arm/cpu/arm1176/start.S
@@ -108,12 +108,6 @@ _TEXT_BASE:
_TEXT_PHY_BASE:
.word CONFIG_SYS_PHY_UBOOT_BASE
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
-.globl _armboot_start
-_armboot_start:
- .word _start
-#endif
-
/*
* These are defined in the board-specific linker script.
* Subtracting _start from them lets the linker put their
@@ -157,7 +151,6 @@ _rel_dyn_end_ofs:
_dynsym_start_ofs:
.word __dynsym_start - _start
-#if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
/* IRQ stack memory (calculated at run-time) + 8 bytes */
.globl IRQ_STACK_START_IN
IRQ_STACK_START_IN:
@@ -419,188 +412,6 @@ _board_init_r_ofs:
.word board_init_r - _start
#endif
-#else /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
-
-/*
- * the actual reset code
- */
-
-reset:
- /*
- * set the cpu to SVC32 mode
- */
- mrs r0, cpsr
- bic r0, r0, #0x3f
- orr r0, r0, #0xd3
- msr cpsr, r0
-
-/*
- *************************************************************************
- *
- * CPU_init_critical registers
- *
- * setup important registers
- * setup memory timing
- *
- *************************************************************************
- */
- /*
- * we do sys-critical inits only at reboot,
- * not when booting from ram!
- */
-cpu_init_crit:
- /*
- * When booting from NAND - it has definitely been a reset, so, no need
- * to flush caches and disable the MMU
- */
-#ifndef CONFIG_NAND_SPL
- /*
- * flush v4 I/D caches
- */
- mov r0, #0
- mcr p15, 0, r0, c7, c7, 0 /* flush v3/v4 cache */
- mcr p15, 0, r0, c8, c7, 0 /* flush v4 TLB */
-
- /*
- * disable MMU stuff and caches
- */
- mrc p15, 0, r0, c1, c0, 0
- bic r0, r0, #0x00002300 @ clear bits 13, 9:8 (--V- --RS)
- bic r0, r0, #0x00000087 @ clear bits 7, 2:0 (B--- -CAM)
- orr r0, r0, #0x00000002 @ set bit 2 (A) Align
- orr r0, r0, #0x00001000 @ set bit 12 (I) I-Cache
-
- /* Prepare to disable the MMU */
- adr r2, mmu_disable_phys
- sub r2, r2, #(CONFIG_SYS_PHY_UBOOT_BASE - CONFIG_SYS_TEXT_BASE)
- b mmu_disable
-
- .align 5
- /* Run in a single cache-line */
-mmu_disable:
- mcr p15, 0, r0, c1, c0, 0
- nop
- nop
- mov pc, r2
-mmu_disable_phys:
-
-#ifdef CONFIG_DISABLE_TCM
- /*
- * Disable the TCMs
- */
- mrc p15, 0, r0, c0, c0, 2 /* Return TCM details */
- cmp r0, #0
- beq skip_tcmdisable
- mov r1, #0
- mov r2, #1
- tst r0, r2
- mcrne p15, 0, r1, c9, c1, 1 /* Disable Instruction TCM if present*/
- tst r0, r2, LSL #16
- mcrne p15, 0, r1, c9, c1, 0 /* Disable Data TCM if present*/
-skip_tcmdisable:
-#endif
-#endif
-
-#ifdef CONFIG_PERIPORT_REMAP
- /* Peri port setup */
- ldr r0, =CONFIG_PERIPORT_BASE
- orr r0, r0, #CONFIG_PERIPORT_SIZE
- mcr p15,0,r0,c15,c2,4
-#endif
-
- /*
- * Go setup Memory and board specific bits prior to relocation.
- */
- bl lowlevel_init /* go setup pll,mux,memory */
-
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
-relocate: /* relocate U-Boot to RAM */
- adr r0, _start /* r0 <- current position of code */
- ldr r1, _TEXT_BASE /* test if we run from flash or RAM */
- cmp r0, r1 /* don't reloc during debug */
- beq stack_setup
-
- ldr r2, _armboot_start
- ldr r3, _bss_start
- sub r2, r3, r2 /* r2 <- size of armboot */
- add r2, r0, r2 /* r2 <- source end address */
-
-copy_loop:
- ldmia r0!, {r3-r10} /* copy from source address [r0] */
- stmia r1!, {r3-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- blo copy_loop
-#endif /* CONFIG_SKIP_RELOCATE_UBOOT */
-
-#ifdef CONFIG_ENABLE_MMU
-enable_mmu:
- /* enable domain access */
- ldr r5, =0x0000ffff
- mcr p15, 0, r5, c3, c0, 0 /* load domain access register */
-
- /* Set the TTB register */
- ldr r0, _mmu_table_base
- ldr r1, =CONFIG_SYS_PHY_UBOOT_BASE
- ldr r2, =0xfff00000
- bic r0, r0, r2
- orr r1, r0, r1
- mcr p15, 0, r1, c2, c0, 0
-
- /* Enable the MMU */
- mrc p15, 0, r0, c1, c0, 0
- orr r0, r0, #1 /* Set CR_M to enable MMU */
-
- /* Prepare to enable the MMU */
- adr r1, skip_hw_init
- and r1, r1, #0x3fc
- ldr r2, _TEXT_BASE
- ldr r3, =0xfff00000
- and r2, r2, r3
- orr r2, r2, r1
- b mmu_enable
-
- .align 5
- /* Run in a single cache-line */
-mmu_enable:
-
- mcr p15, 0, r0, c1, c0, 0
- nop
- nop
- mov pc, r2
-skip_hw_init:
-#endif
-
- /* Set up the stack */
-stack_setup:
- ldr r0, =CONFIG_SYS_UBOOT_BASE /* base of copy in DRAM */
- sub r0, r0, #CONFIG_SYS_MALLOC_LEN /* malloc area */
- sub r0, r0, #GENERATED_GBL_DATA_SIZE /* bdinfo */
- sub sp, r0, #12 /* leave 3 words for abort-stack */
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
-
-clear_bss:
- ldr r0, _bss_start /* find start of bss segment */
- ldr r1, _bss_end /* stop here */
- mov r2, #0 /* clear */
-
-clbss_l:
- str r2, [r0] /* clear loop... */
- add r0, r0, #4
- cmp r0, r1
- blo clbss_l
-
-#ifndef CONFIG_NAND_SPL
- ldr pc, _start_armboot
-
-_start_armboot:
- .word start_armboot
-#else
- b nand_boot
-/* .word nand_boot*/
-#endif
-
-#endif /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
-
#ifdef CONFIG_ENABLE_MMU
_mmu_table_base:
.word mmu_table
@@ -687,14 +498,7 @@ phy_last_jump:
/* Save user registers (now in svc mode) r0-r12 */
stmia sp, {r0 - r12}
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
- ldr r2, _armboot_start
- sub r2, r2, #(CONFIG_SYS_MALLOC_LEN)
- /* set base 2 words into abort stack */
- sub r2, r2, #(GENERATED_GBL_DATA_SIZE+8)
-#else
ldr r2, IRQ_STACK_START_IN
-#endif
/* get values for "aborted" pc and cpsr (into parm regs) */
ldmia r2, {r2 - r3}
/* grab pointer to old stack */
@@ -709,16 +513,7 @@ phy_last_jump:
.endm
.macro get_bad_stack
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
- /* setup our mode stack (enter in banked mode) */
- ldr r13, _armboot_start
- /* move past malloc pool */
- sub r13, r13, #(CONFIG_SYS_MALLOC_LEN)
- /* move to reserved a couple spots for abort stack */
- sub r13, r13, #(GENERATED_GBL_DATA_SIZE + 8)
-#else
ldr r13, IRQ_STACK_START_IN @ setup our mode stack
-#endif
/* save caller lr in position 0 of saved stack */
str lr, [r13]
@@ -743,16 +538,7 @@ phy_last_jump:
sub r13, r13, #4
/* save R0's value. */
str r0, [r13]
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
- /* get data regions start */
- ldr r0, _armboot_start
- /* move past malloc pool */
- sub r0, r0, #(CONFIG_SYS_MALLOC_LEN)
- /* move past gbl and a couple spots for abort stack */
- sub r0, r0, #(GENERATED_GBL_DATA_SIZE + 8)
-#else
ldr r13, IRQ_STACK_START_IN @ setup our mode stack
-#endif
/* save caller lr in position 0 of saved stack */
str lr, [r0]
/* get the spsr */
diff --git a/arch/arm/cpu/arm720t/start.S b/arch/arm/cpu/arm720t/start.S
index 41c1519efe..b94ecb4353 100644
--- a/arch/arm/cpu/arm720t/start.S
+++ b/arch/arm/cpu/arm720t/start.S
@@ -79,12 +79,6 @@ _fiq: .word fiq
_TEXT_BASE:
.word CONFIG_SYS_TEXT_BASE
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
-.globl _armboot_start
-_armboot_start:
- .word _start
-#endif
-
/*
* These are defined in the board-specific linker script.
*/
@@ -108,7 +102,6 @@ FIQ_STACK_START:
.word 0x0badc0de
#endif
-#if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
/* IRQ stack memory (calculated at run-time) + 8 bytes */
.globl IRQ_STACK_START_IN
IRQ_STACK_START_IN:
@@ -264,92 +257,6 @@ clbss_l:str r2, [r0] /* clear loop... */
_board_init_r: .word board_init_r
-#else /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
-
-/*
- * the actual reset code
- */
-
-reset:
- /*
- * set the cpu to SVC32 mode
- */
- mrs r0,cpsr
- bic r0,r0,#0x1f
- orr r0,r0,#0x13
- msr cpsr,r0
-
- /*
- * we do sys-critical inits only at reboot,
- * not when booting from ram!
- */
-#ifndef CONFIG_SKIP_LOWLEVEL_INIT
- bl cpu_init_crit
-#endif
-
-#ifdef CONFIG_LPC2292
- bl lowlevel_init
-#endif
-
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
-relocate: /* relocate U-Boot to RAM */
- adr r0, _start /* r0 <- current position of code */
- ldr r1, _TEXT_BASE /* test if we run from flash or RAM */
- cmp r0, r1 /* don't reloc during debug */
- beq stack_setup
-
-#if CONFIG_SYS_TEXT_BASE
-#ifndef CONFIG_LPC2292 /* already done in lowlevel_init */
- ldr r2, =0x0 /* Relocate the exception vectors */
- cmp r1, r2 /* and associated data to address */
- ldmneia r0!, {r3-r10} /* 0x0. Do nothing if CONFIG_SYS_TEXT_BASE is */
- stmneia r2!, {r3-r10} /* 0x0. Copy the first 15 words. */
- ldmneia r0, {r3-r9}
- stmneia r2, {r3-r9}
- adrne r0, _start /* restore r0 */
-#endif /* !CONFIG_LPC2292 */
-#endif
-
- ldr r2, _armboot_start
- ldr r3, _bss_start
- sub r2, r3, r2 /* r2 <- size of armboot */
- add r2, r0, r2 /* r2 <- source end address */
-
-copy_loop:
- ldmia r0!, {r3-r10} /* copy from source address [r0] */
- stmia r1!, {r3-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- blo copy_loop
-
-#endif /* CONFIG_SKIP_RELOCATE_UBOOT */
-
- /* Set up the stack */
-stack_setup:
- ldr r0, _TEXT_BASE /* upper 128 KiB: relocated uboot */
- sub r0, r0, #CONFIG_SYS_MALLOC_LEN /* malloc area */
- sub r0, r0, #GENERATED_GBL_DATA_SIZE /* bdinfo */
-#ifdef CONFIG_USE_IRQ
- sub r0, r0, #(CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ)
-#endif
- sub sp, r0, #12 /* leave 3 words for abort-stack */
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
-
-clear_bss:
- ldr r0, _bss_start /* find start of bss segment */
- ldr r1, _bss_end /* stop here */
- mov r2, #0x00000000 /* clear */
-
-clbss_l:str r2, [r0] /* clear loop... */
- add r0, r0, #4
- cmp r0, r1
- blo clbss_l
-
- ldr pc, _start_armboot
-
-_start_armboot: .word start_armboot
-
-#endif /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
-
/*
*************************************************************************
*
@@ -606,13 +513,7 @@ lock_loop:
stmia sp, {r0 - r12} @ Calling r0-r12
add r8, sp, #S_PC
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
- ldr r2, _armboot_start
- sub r2, r2, #(CONFIG_STACKSIZE+CONFIG_SYS_MALLOC_LEN)
- sub r2, r2, #(GENERATED_GBL_DATA_SIZE+8) @ set base 2 words into abort stack
-#else
ldr r2, IRQ_STACK_START_IN
-#endif
ldmia r2, {r2 - r4} @ get pc, cpsr, old_r0
add r0, sp, #S_FRAME_SIZE @ restore sp_SVC
@@ -643,13 +544,7 @@ lock_loop:
.endm
.macro get_bad_stack
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
- ldr r13, _armboot_start @ setup our mode stack
- sub r13, r13, #(CONFIG_STACKSIZE+CONFIG_SYS_MALLOC_LEN)
- sub r13, r13, #(GENERATED_GBL_DATA_SIZE+8) @ reserved a couple spots in abort stack
-#else
ldr r13, IRQ_STACK_START_IN @ setup our mode stack
-#endif
str lr, [r13] @ save caller lr / spsr
mrs lr, spsr
diff --git a/arch/arm/cpu/arm920t/start.S b/arch/arm/cpu/arm920t/start.S
index f0274b1f82..08d4e7bc3d 100644
--- a/arch/arm/cpu/arm920t/start.S
+++ b/arch/arm/cpu/arm920t/start.S
@@ -75,12 +75,6 @@ _fiq: .word fiq
_TEXT_BASE:
.word CONFIG_SYS_TEXT_BASE
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
-.globl _armboot_start
-_armboot_start:
- .word _start
-#endif
-
/*
* These are defined in the board-specific linker script.
*/
@@ -104,7 +98,6 @@ FIQ_STACK_START:
.word 0x0badc0de
#endif
-#if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
/* IRQ stack memory (calculated at run-time) + 8 bytes */
.globl IRQ_STACK_START_IN
IRQ_STACK_START_IN:
@@ -316,127 +309,6 @@ _nand_boot: .word nand_boot
_board_init_r: .word board_init_r
#endif
-#else /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
-/*
- * the actual start code
- */
-
-start_code:
- /*
- * set the cpu to SVC32 mode
- */
- mrs r0, cpsr
- bic r0, r0, #0x1f
- orr r0, r0, #0xd3
- msr cpsr, r0
-
- bl coloured_LED_init
- bl red_LED_on
-
-#if defined(CONFIG_AT91RM9200DK) || defined(CONFIG_AT91RM9200EK)
- /*
- * relocate exception table
- */
- ldr r0, =_start
- ldr r1, =0x0
- mov r2, #16
-copyex:
- subs r2, r2, #1
- ldr r3, [r0], #4
- str r3, [r1], #4
- bne copyex
-#endif
-
-#ifdef CONFIG_S3C24X0
- /* turn off the watchdog */
-
-# if defined(CONFIG_S3C2400)
-# define pWTCON 0x15300000
-# define INTMSK 0x14400008 /* Interupt-Controller base addresses */
-# define CLKDIVN 0x14800014 /* clock divisor register */
-#else
-# define pWTCON 0x53000000
-# define INTMSK 0x4A000008 /* Interupt-Controller base addresses */
-# define INTSUBMSK 0x4A00001C
-# define CLKDIVN 0x4C000014 /* clock divisor register */
-# endif
-
- ldr r0, =pWTCON
- mov r1, #0x0
- str r1, [r0]
-
- /*
- * mask all IRQs by setting all bits in the INTMR - default
- */
- mov r1, #0xffffffff
- ldr r0, =INTMSK
- str r1, [r0]
-# if defined(CONFIG_S3C2410)
- ldr r1, =0x3ff
- ldr r0, =INTSUBMSK
- str r1, [r0]
-# endif
-
- /* FCLK:HCLK:PCLK = 1:2:4 */
- /* default FCLK is 120 MHz ! */
- ldr r0, =CLKDIVN
- mov r1, #3
- str r1, [r0]
-#endif /* CONFIG_S3C24X0 */
-
- /*
- * we do sys-critical inits only at reboot,
- * not when booting from ram!
- */
-#ifndef CONFIG_SKIP_LOWLEVEL_INIT
- bl cpu_init_crit
-#endif
-
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
-relocate: /* relocate U-Boot to RAM */
- adr r0, _start /* r0 <- current position of code */
- ldr r1, _TEXT_BASE /* test if we run from flash or RAM */
- cmp r0, r1 /* don't reloc during debug */
- beq stack_setup
-
- ldr r2, _armboot_start
- ldr r3, _bss_start
- sub r2, r3, r2 /* r2 <- size of armboot */
- add r2, r0, r2 /* r2 <- source end address */
-
-copy_loop:
- ldmia r0!, {r3-r10} /* copy from source address [r0] */
- stmia r1!, {r3-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- blo copy_loop
-#endif /* CONFIG_SKIP_RELOCATE_UBOOT */
-
- /* Set up the stack */
-stack_setup:
- ldr r0, _TEXT_BASE /* upper 128 KiB: relocated uboot */
- sub r0, r0, #CONFIG_SYS_MALLOC_LEN /* malloc area */
- sub r0, r0, #GENERATED_GBL_DATA_SIZE /* bdinfo */
-#ifdef CONFIG_USE_IRQ
- sub r0, r0, #(CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ)
-#endif
- sub sp, r0, #12 /* leave 3 words for abort-stack */
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
-
-clear_bss:
- ldr r0, _bss_start /* find start of bss segment */
- ldr r1, _bss_end /* stop here */
- mov r2, #0x00000000 /* clear */
-
-clbss_l:str r2, [r0] /* clear loop... */
- add r0, r0, #4
- cmp r0, r1
- blo clbss_l
-
- ldr pc, _start_armboot
-
-_start_armboot: .word start_armboot
-#endif /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
-
/*
*************************************************************************
*
@@ -525,15 +397,7 @@ cpu_init_crit:
.macro bad_save_user_regs
sub sp, sp, #S_FRAME_SIZE
stmia sp, {r0 - r12} @ Calling r0-r12
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
- ldr r2, _armboot_start
- sub r2, r2, #(CONFIG_STACKSIZE)
- sub r2, r2, #(CONFIG_SYS_MALLOC_LEN)
- /* set base 2 words into abort stack */
- sub r2, r2, #(GENERATED_GBL_DATA_SIZE+8)
-#else
ldr r2, IRQ_STACK_START_IN
-#endif
ldmia r2, {r2 - r3} @ get pc, cpsr
add r0, sp, #S_FRAME_SIZE @ restore sp_SVC
@@ -565,15 +429,7 @@ cpu_init_crit:
.endm
.macro get_bad_stack
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
- ldr r13, _armboot_start @ setup our mode stack
- sub r13, r13, #(CONFIG_STACKSIZE)
- sub r13, r13, #(CONFIG_SYS_MALLOC_LEN)
- /* reserve a couple spots in abort stack */
- sub r13, r13, #(GENERATED_GBL_DATA_SIZE+8)
-#else
ldr r13, IRQ_STACK_START_IN @ setup our mode stack
-#endif
str lr, [r13] @ save caller lr / spsr
mrs lr, spsr
diff --git a/arch/arm/cpu/arm925t/start.S b/arch/arm/cpu/arm925t/start.S
index 2ad2df847e..6792a22aff 100644
--- a/arch/arm/cpu/arm925t/start.S
+++ b/arch/arm/cpu/arm925t/start.S
@@ -85,12 +85,6 @@ _fiq: .word fiq
_TEXT_BASE:
.word CONFIG_SYS_TEXT_BASE
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
-.globl _armboot_start
-_armboot_start:
- .word _start
-#endif
-
/*
* These are defined in the board-specific linker script.
*/
@@ -114,7 +108,6 @@ FIQ_STACK_START:
.word 0x0badc0de
#endif
-#if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
/* IRQ stack memory (calculated at run-time) + 8 bytes */
.globl IRQ_STACK_START_IN
IRQ_STACK_START_IN:
@@ -305,108 +298,6 @@ _nand_boot: .word nand_boot
_board_init_r: .word board_init_r
#endif
-#else /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
-/*
- * the actual reset code
- */
-
-reset:
- /*
- * set the cpu to SVC32 mode
- */
- mrs r0,cpsr
- bic r0,r0,#0x1f
- orr r0,r0,#0xd3
- msr cpsr,r0
-
- /*
- * Set up 925T mode
- */
- mov r1, #0x81 /* Set ARM925T configuration. */
- mcr p15, 0, r1, c15, c1, 0 /* Write ARM925T configuration register. */
-
- /*
- * turn off the watchdog, unlock/diable sequence
- */
- mov r1, #0xF5
- ldr r0, =WDTIM_MODE
- strh r1, [r0]
- mov r1, #0xA0
- strh r1, [r0]
-
- /*
- * mask all IRQs by setting all bits in the INTMR - default
- */
- mov r1, #0xffffffff
- ldr r0, =REG_IHL1_MIR
- str r1, [r0]
- ldr r0, =REG_IHL2_MIR
- str r1, [r0]
-
- /*
- * wait for dpll to lock
- */
- ldr r0, =CK_DPLL1
- mov r1, #0x10
- strh r1, [r0]
-poll1:
- ldrh r1, [r0]
- ands r1, r1, #0x01
- beq poll1
-
- /*
- * we do sys-critical inits only at reboot,
- * not when booting from ram!
- */
-#ifndef CONFIG_SKIP_LOWLEVEL_INIT
- bl cpu_init_crit
-#endif
-
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
-relocate: /* relocate U-Boot to RAM */
- adr r0, _start /* r0 <- current position of code */
- ldr r1, _TEXT_BASE /* test if we run from flash or RAM */
- cmp r0, r1 /* don't reloc during debug */
- beq stack_setup
-
- ldr r2, _armboot_start
- ldr r3, _bss_start
- sub r2, r3, r2 /* r2 <- size of armboot */
- add r2, r0, r2 /* r2 <- source end address */
-
-copy_loop:
- ldmia r0!, {r3-r10} /* copy from source address [r0] */
- stmia r1!, {r3-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- blo copy_loop
-#endif /* CONFIG_SKIP_RELOCATE_UBOOT */
-
- /* Set up the stack */
-stack_setup:
- ldr r0, _TEXT_BASE /* upper 128 KiB: relocated uboot */
- sub r0, r0, #CONFIG_SYS_MALLOC_LEN /* malloc area */
- sub r0, r0, #GENERATED_GBL_DATA_SIZE /* bdinfo */
-#ifdef CONFIG_USE_IRQ
- sub r0, r0, #(CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ)
-#endif
- sub sp, r0, #12 /* leave 3 words for abort-stack */
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
-
-clear_bss:
- ldr r0, _bss_start /* find start of bss segment */
- ldr r1, _bss_end /* stop here */
- mov r2, #0x00000000 /* clear */
-
-clbss_l:str r2, [r0] /* clear loop... */
- add r0, r0, #4
- cmp r0, r1
- blo clbss_l
-
- ldr pc, _start_armboot
-
-_start_armboot: .word start_armboot
-#endif /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
-
/*
*************************************************************************
*
@@ -489,13 +380,7 @@ cpu_init_crit:
sub sp, sp, #S_FRAME_SIZE @ carve out a frame on current user stack
stmia sp, {r0 - r12} @ Save user registers (now in svc mode) r0-r12
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
- ldr r2, _armboot_start
- sub r2, r2, #(CONFIG_STACKSIZE+CONFIG_SYS_MALLOC_LEN)
- sub r2, r2, #(GENERATED_GBL_DATA_SIZE+8) @ set base 2 words into abort stack
-#else
ldr r2, IRQ_STACK_START_IN
-#endif
ldmia r2, {r2 - r3} @ get values for "aborted" pc and cpsr (into parm regs)
add r0, sp, #S_FRAME_SIZE @ grab pointer to old stack
@@ -526,13 +411,7 @@ cpu_init_crit:
.endm
.macro get_bad_stack
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
- ldr r13, _armboot_start @ setup our mode stack
- sub r13, r13, #(CONFIG_STACKSIZE+CONFIG_SYS_MALLOC_LEN)
- sub r13, r13, #(GENERATED_GBL_DATA_SIZE+8) @ reserved a couple spots in abort stack
-#else
ldr r13, IRQ_STACK_START_IN
-#endif
str lr, [r13] @ save caller lr in position 0 of saved stack
mrs lr, spsr @ get the spsr
diff --git a/arch/arm/cpu/arm926ejs/orion5x/dram.c b/arch/arm/cpu/arm926ejs/orion5x/dram.c
index c5c8ab7e4d..b749282099 100644
--- a/arch/arm/cpu/arm926ejs/orion5x/dram.c
+++ b/arch/arm/cpu/arm926ejs/orion5x/dram.c
@@ -49,20 +49,6 @@ u32 orion5x_sdram_bar(enum memory_bank bank)
result = winregs[bank].base;
return result;
}
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
-int dram_init(void)
-{
- int i;
-
- for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
- gd->bd->bi_dram[i].start = orion5x_sdram_bar(i);
- gd->bd->bi_dram[i].size = get_ram_size(
- (volatile long *) (gd->bd->bi_dram[i].start),
- CONFIG_MAX_RAM_BANK_SIZE);
- }
- return 0;
-}
-#else
int dram_init (void)
{
/* dram_init must store complete ramsize in gd->ram_size */
@@ -83,4 +69,3 @@ void dram_init_banksize (void)
CONFIG_MAX_RAM_BANK_SIZE);
}
}
-#endif
diff --git a/arch/arm/cpu/arm926ejs/start.S b/arch/arm/cpu/arm926ejs/start.S
index 7397882b59..4f689c1ef5 100644
--- a/arch/arm/cpu/arm926ejs/start.S
+++ b/arch/arm/cpu/arm926ejs/start.S
@@ -145,7 +145,6 @@ FIQ_STACK_START:
.word 0x0badc0de
#endif
-#if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
/* IRQ stack memory (calculated at run-time) + 8 bytes */
.globl IRQ_STACK_START_IN
IRQ_STACK_START_IN:
@@ -307,89 +306,6 @@ _rel_dyn_end_ofs:
_dynsym_start_ofs:
.word __dynsym_start - _start
-#else /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
-/*
- * the actual reset code
- */
-
-reset:
- /*
- * set the cpu to SVC32 mode
- */
- mrs r0,cpsr
- bic r0,r0,#0x1f
- orr r0,r0,#0xd3
- msr cpsr,r0
-
- /*
- * we do sys-critical inits only at reboot,
- * not when booting from ram!
- */
-#ifndef CONFIG_SKIP_LOWLEVEL_INIT
- bl cpu_init_crit
-#endif
-
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
-relocate: /* relocate U-Boot to RAM */
- adr r0, _start /* r0 <- current position of code */
- ldr r1, _TEXT_BASE /* test if we run from flash or RAM */
- cmp r0, r1 /* don't reloc during debug */
- beq stack_setup
- ldr r3, _bss_start_ofs /* r3 <- _bss_start - _start */
- add r2, r0, r3 /* r2 <- source end address */
-
-copy_loop:
- ldmia r0!, {r3-r10} /* copy from source address [r0] */
- stmia r1!, {r3-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- blo copy_loop
-#endif /* CONFIG_SKIP_RELOCATE_UBOOT */
-
- /* Set up the stack */
-stack_setup:
- ldr r0, _TEXT_BASE /* upper 128 KiB: relocated uboot */
- sub sp, r0, #128 /* leave 32 words for abort-stack */
-#ifndef CONFIG_PRELOADER
- sub r0, r0, #CONFIG_SYS_MALLOC_LEN /* malloc area */
- sub r0, r0, #GENERATED_GBL_DATA_SIZE /* bdinfo */
-#ifdef CONFIG_USE_IRQ
- sub r0, r0, #(CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ)
-#endif
-#endif /* CONFIG_PRELOADER */
- sub sp, r0, #12 /* leave 3 words for abort-stack */
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
-
-clear_bss:
- adr r2, _start
- ldr r0, _bss_start_ofs /* find start of bss segment */
- add r0, r0, r2
- ldr r1, _bss_end_ofs /* stop here */
- add r1, r1, r2
- mov r2, #0x00000000 /* clear */
-
-#ifndef CONFIG_PRELOADER
-clbss_l:str r2, [r0] /* clear loop... */
- add r0, r0, #4
- cmp r0, r1
- blo clbss_l
-
- bl coloured_LED_init
- bl red_LED_on
-#endif /* CONFIG_PRELOADER */
-
- ldr r0, _start_armboot_ofs
- adr r1, _start
- add r0, r0, r1
- ldr pc, r0
-
-_start_armboot_ofs:
-#ifdef CONFIG_NAND_SPL
- .word nand_boot - _start
-#else
- .word start_armboot - _start
-#endif /* CONFIG_NAND_SPL */
-#endif /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
-
/*
*************************************************************************
*
@@ -474,13 +390,7 @@ cpu_init_crit:
@ carve out a frame on current user stack
sub sp, sp, #S_FRAME_SIZE
stmia sp, {r0 - r12} @ Save user registers (now in svc mode) r0-r12
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
- adr r2, _start
- sub r2, r2, #(CONFIG_STACKSIZE+CONFIG_SYS_MALLOC_LEN)
- sub r2, r2, #(GENERATED_GBL_DATA_SIZE+8) @ set base 2 words into abort stack
-#else
ldr r2, IRQ_STACK_START_IN
-#endif
@ get values for "aborted" pc and cpsr (into parm regs)
ldmia r2, {r2 - r3}
add r0, sp, #S_FRAME_SIZE @ grab pointer to old stack
@@ -512,13 +422,7 @@ cpu_init_crit:
.endm
.macro get_bad_stack
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
- adr r13, _start @ setup our mode stack
- sub r13, r13, #(CONFIG_STACKSIZE+CONFIG_SYS_MALLOC_LEN)
- sub r13, r13, #(GENERATED_GBL_DATA_SIZE+8) @ reserved a couple spots in abort stack
-#else
ldr r13, IRQ_STACK_START_IN @ setup our mode stack
-#endif
str lr, [r13] @ save caller lr in position 0 of saved stack
mrs lr, spsr @ get the spsr
diff --git a/arch/arm/cpu/arm946es/start.S b/arch/arm/cpu/arm946es/start.S
index 22af2fae95..7378edc41c 100644
--- a/arch/arm/cpu/arm946es/start.S
+++ b/arch/arm/cpu/arm946es/start.S
@@ -89,12 +89,6 @@ _fiq:
_TEXT_BASE:
.word CONFIG_SYS_TEXT_BASE
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
-.globl _armboot_start
-_armboot_start:
- .word _start
-#endif
-
/*
* These are defined in the board-specific linker script.
*/
@@ -118,7 +112,6 @@ FIQ_STACK_START:
.word 0x0badc0de
#endif
-#if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
/* IRQ stack memory (calculated at run-time) + 8 bytes */
.globl IRQ_STACK_START_IN
IRQ_STACK_START_IN:
@@ -273,72 +266,6 @@ _nand_boot: .word nand_boot
_board_init_r: .word board_init_r
#endif
-#else /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
-/*
- * the actual reset code
- */
-
-reset:
- /*
- * set the cpu to SVC32 mode
- */
- mrs r0,cpsr
- bic r0,r0,#0x1f
- orr r0,r0,#0xd3
- msr cpsr,r0
-
- /*
- * we do sys-critical inits only at reboot,
- * not when booting from ram!
- */
-#ifndef CONFIG_SKIP_LOWLEVEL_INIT
- bl cpu_init_crit
-#endif
-
-relocate: /* relocate U-Boot to RAM */
- adr r0, _start /* r0 <- current position of code */
- ldr r1, _TEXT_BASE /* test if we run from flash or RAM */
- cmp r0, r1 /* don't reloc during debug */
- beq stack_setup
-
- ldr r2, _armboot_start
- ldr r3, _bss_start
- sub r2, r3, r2 /* r2 <- size of armboot */
- add r2, r0, r2 /* r2 <- source end address */
-
-copy_loop:
- ldmia r0!, {r3-r10} /* copy from source address [r0] */
- stmia r1!, {r3-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- blo copy_loop
-
- /* Set up the stack */
-stack_setup:
- ldr r0, _TEXT_BASE /* upper 128 KiB: relocated uboot */
- sub r0, r0, #CONFIG_SYS_MALLOC_LEN /* malloc area */
- sub r0, r0, #GENERATED_GBL_DATA_SIZE /* bdinfo */
-#ifdef CONFIG_USE_IRQ
- sub r0, r0, #(CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ)
-#endif
- sub sp, r0, #12 /* leave 3 words for abort-stack */
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
-
-clear_bss:
- ldr r0, _bss_start /* find start of bss segment */
- ldr r1, _bss_end /* stop here */
- mov r2, #0x00000000 /* clear */
-
-clbss_l:str r2, [r0] /* clear loop... */
- add r0, r0, #4
- cmp r0, r1
- bne clbss_l
-
- ldr pc, _start_armboot
-
-_start_armboot:
- .word start_armboot
-#endif /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
-
/*
*************************************************************************
*
@@ -424,13 +351,7 @@ cpu_init_crit:
sub sp, sp, #S_FRAME_SIZE
stmia sp, {r0 - r12} @ Save user registers (now in svc mode) r0-r12
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
- ldr r2, _armboot_start
- sub r2, r2, #(CONFIG_STACKSIZE+CONFIG_SYS_MALLOC_LEN)
- sub r2, r2, #(GENERATED_GBL_DATA_SIZE+8) @ set base 2 words into abort stack
-#else
ldr r2, IRQ_STACK_START_IN
-#endif
@ get values for "aborted" pc and cpsr (into parm regs)
ldmia r2, {r2 - r3}
add r0, sp, #S_FRAME_SIZE @ grab pointer to old stack
@@ -462,13 +383,7 @@ cpu_init_crit:
.endm
.macro get_bad_stack
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
- ldr r13, _armboot_start @ setup our mode stack
- sub r13, r13, #(CONFIG_STACKSIZE+CONFIG_SYS_MALLOC_LEN)
- sub r13, r13, #(GENERATED_GBL_DATA_SIZE+8) @ reserved a couple spots in abort stack
-#else
ldr r13, IRQ_STACK_START_IN @ setup our mode stack
-#endif
str lr, [r13] @ save caller lr in position 0 of saved stack
mrs lr, spsr @ get the spsr
diff --git a/arch/arm/cpu/arm_intcm/start.S b/arch/arm/cpu/arm_intcm/start.S
index a420f44ff5..2240f3a524 100644
--- a/arch/arm/cpu/arm_intcm/start.S
+++ b/arch/arm/cpu/arm_intcm/start.S
@@ -87,12 +87,6 @@ _fiq:
_TEXT_BASE:
.word CONFIG_SYS_TEXT_BASE /* address of _start in the linked image */
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
-.globl _armboot_start
-_armboot_start:
- .word _start
-#endif
-
/*
* These are defined in the board-specific linker script.
*/
@@ -116,7 +110,6 @@ FIQ_STACK_START:
.word 0x0badc0de
#endif
-#if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
/* IRQ stack memory (calculated at run-time) + 8 bytes */
.globl IRQ_STACK_START_IN
IRQ_STACK_START_IN:
@@ -268,74 +261,6 @@ clbss_l:str r2, [r0] /* clear loop... */
_board_init_r: .word board_init_r
-#else /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
-
-/*
- * the actual reset code
- */
-.globl reset
-reset:
- /*
- * set the cpu to SVC32 mode
- */
- mrs r0,cpsr
- bic r0,r0,#0x1f
- orr r0,r0,#0xd3
- msr cpsr,r0
-
- /*
- * we do sys-critical inits only at reboot,
- * not when booting from ram!
- */
-#ifndef CONFIG_SKIP_LOWLEVEL_INIT
- bl cpu_init_crit
-#endif
-
-relocate: /* relocate U-Boot to RAM */
- adr r0, _start /* pc relative address of label */
- ldr r1, _TEXT_BASE /* linked image address of label */
- cmp r0, r1 /* test if we run from flash or RAM */
- beq stack_setup /* ifeq we are in the RAM copy */
-
- ldr r2, _armboot_start
- ldr r3, _bss_start
- sub r2, r3, r2 /* r2 <- size of armboot */
- add r2, r0, r2 /* r2 <- source end address */
-
-copy_loop:
- ldmia r0!, {r3-r10} /* copy from source address [r0] */
- stmia r1!, {r3-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- blo copy_loop
-
- /* Set up the stack */
-stack_setup:
- ldr r0, _TEXT_BASE /* upper 128 KiB: relocated uboot */
- sub r0, r0, #CONFIG_SYS_MALLOC_LEN /* malloc area */
- sub r0, r0, #GENERATED_GBL_DATA_SIZE /* bdinfo */
-#ifdef CONFIG_USE_IRQ
- sub r0, r0, #(CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ)
-#endif
- sub sp, r0, #12 /* leave 3 words for abort-stack */
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
-
-clear_bss:
- ldr r0, _bss_start /* find start of bss segment */
- ldr r1, _bss_end /* stop here */
- mov r2, #0x00000000 /* clear */
-
-clbss_l:str r2, [r0] /* clear loop... */
- add r0, r0, #4
- cmp r0, r1
- blo clbss_l
-
- ldr pc, _start_armboot
-
-_start_armboot:
- .word start_armboot
-
-#endif /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
-
/*
*************************************************************************
*
@@ -400,13 +325,7 @@ cpu_init_crit:
sub sp, sp, #S_FRAME_SIZE
stmia sp, {r0 - r12} @ Save user registers (now in svc mode) r0-r12
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
- ldr r2, _armboot_start
- sub r2, r2, #(CONFIG_STACKSIZE+CONFIG_SYS_MALLOC_LEN)
- sub r2, r2, #(GENERATED_GBL_DATA_SIZE+8) @ set base 2 words into abort stack
-#else
ldr r2, IRQ_STACK_START_IN
-#endif
@ get values for "aborted" pc and cpsr (into parm regs)
ldmia r2, {r2 - r3}
add r0, sp, #S_FRAME_SIZE @ grab pointer to old stack
@@ -438,13 +357,7 @@ cpu_init_crit:
.endm
.macro get_bad_stack
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
- ldr r13, _armboot_start @ setup our mode stack
- sub r13, r13, #(CONFIG_STACKSIZE+CONFIG_SYS_MALLOC_LEN)
- sub r13, r13, #(GENERATED_GBL_DATA_SIZE+8) @ reserved a couple spots in abort stack
-#else
ldr r13, IRQ_STACK_START_IN @ setup our mode stack
-#endif
str lr, [r13] @ save caller lr in position 0 of saved stack
mrs lr, spsr @ get the spsr
diff --git a/arch/arm/cpu/armv7/omap3/emif4.c b/arch/arm/cpu/armv7/omap3/emif4.c
index da2cd90013..0870857ede 100644
--- a/arch/arm/cpu/armv7/omap3/emif4.c
+++ b/arch/arm/cpu/armv7/omap3/emif4.c
@@ -136,29 +136,6 @@ void do_emif4_init(void)
* dram_init -
* - Sets uboots idea of sdram size
*/
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
-int dram_init(void)
-{
- DECLARE_GLOBAL_DATA_PTR;
- unsigned int size0 = 0, size1 = 0;
-
- size0 = get_sdr_cs_size(CS0);
- /*
- * If a second bank of DDR is attached to CS1 this is
- * where it can be started. Early init code will init
- * memory on CS0.
- */
- if ((sysinfo.mtype == DDR_COMBO) || (sysinfo.mtype == DDR_STACKED))
- size1 = get_sdr_cs_size(CS1);
-
- gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
- gd->bd->bi_dram[0].size = size0;
- gd->bd->bi_dram[1].start = PHYS_SDRAM_1 + get_sdr_cs_offset(CS1);
- gd->bd->bi_dram[1].size = size1;
-
- return 0;
-}
-#else
int dram_init(void)
{
DECLARE_GLOBAL_DATA_PTR;
@@ -190,7 +167,6 @@ void dram_init_banksize (void)
gd->bd->bi_dram[1].start = PHYS_SDRAM_1 + get_sdr_cs_offset(CS1);
gd->bd->bi_dram[1].size = size1;
}
-#endif
/*
* mem_init() -
diff --git a/arch/arm/cpu/armv7/omap3/sdrc.c b/arch/arm/cpu/armv7/omap3/sdrc.c
index 6c419f5b93..c75aa1d11c 100644
--- a/arch/arm/cpu/armv7/omap3/sdrc.c
+++ b/arch/arm/cpu/armv7/omap3/sdrc.c
@@ -163,33 +163,6 @@ void do_sdrc_init(u32 cs, u32 early)
* dram_init -
* - Sets uboots idea of sdram size
*/
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
-int dram_init(void)
-{
- DECLARE_GLOBAL_DATA_PTR;
- unsigned int size0 = 0, size1 = 0;
-
- size0 = get_sdr_cs_size(CS0);
- /*
- * If a second bank of DDR is attached to CS1 this is
- * where it can be started. Early init code will init
- * memory on CS0.
- */
- if ((sysinfo.mtype == DDR_COMBO) || (sysinfo.mtype == DDR_STACKED)) {
- do_sdrc_init(CS1, NOT_EARLY);
- make_cs1_contiguous();
-
- size1 = get_sdr_cs_size(CS1);
- }
-
- gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
- gd->bd->bi_dram[0].size = size0;
- gd->bd->bi_dram[1].start = PHYS_SDRAM_1 + get_sdr_cs_offset(CS1);
- gd->bd->bi_dram[1].size = size1;
-
- return 0;
-}
-#else
int dram_init(void)
{
DECLARE_GLOBAL_DATA_PTR;
@@ -225,7 +198,6 @@ void dram_init_banksize (void)
gd->bd->bi_dram[1].start = PHYS_SDRAM_1 + get_sdr_cs_offset(CS1);
gd->bd->bi_dram[1].size = size1;
}
-#endif
/*
* mem_init -
diff --git a/arch/arm/cpu/armv7/omap4/board.c b/arch/arm/cpu/armv7/omap4/board.c
index 24a66f5b94..e7651d2dd5 100644
--- a/arch/arm/cpu/armv7/omap4/board.c
+++ b/arch/arm/cpu/armv7/omap4/board.c
@@ -102,12 +102,7 @@ int dram_init(void)
{
DECLARE_GLOBAL_DATA_PTR;
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
- gd->bd->bi_dram[0].start = 0x80000000;
- gd->bd->bi_dram[0].size = sdram_size();
-#else
gd->ram_size = sdram_size();
-#endif
return 0;
}
diff --git a/arch/arm/cpu/armv7/start.S b/arch/arm/cpu/armv7/start.S
index bdf2fad380..4a0710c96d 100644
--- a/arch/arm/cpu/armv7/start.S
+++ b/arch/arm/cpu/armv7/start.S
@@ -70,12 +70,6 @@ _end_vect:
_TEXT_BASE:
.word CONFIG_SYS_TEXT_BASE
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
-.globl _armboot_start
-_armboot_start:
- .word _start
-#endif
-
/*
* These are defined in the board-specific linker script.
*/
@@ -99,7 +93,6 @@ FIQ_STACK_START:
.word 0x0badc0de
#endif
-#if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
/* IRQ stack memory (calculated at run-time) + 8 bytes */
.globl IRQ_STACK_START_IN
IRQ_STACK_START_IN:
@@ -295,94 +288,6 @@ _rel_dyn_end_ofs:
_dynsym_start_ofs:
.word __dynsym_start - _start
-#else /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
-/*
- * the actual reset code
- */
-
-reset:
- /*
- * set the cpu to SVC32 mode
- */
- mrs r0, cpsr
- bic r0, r0, #0x1f
- orr r0, r0, #0xd3
- msr cpsr,r0
-
-#if (CONFIG_OMAP34XX)
- /* Copy vectors to mask ROM indirect addr */
- adr r0, _start @ r0 <- current position of code
- add r0, r0, #4 @ skip reset vector
- mov r2, #64 @ r2 <- size to copy
- add r2, r0, r2 @ r2 <- source end address
- mov r1, #SRAM_OFFSET0 @ build vect addr
- mov r3, #SRAM_OFFSET1
- add r1, r1, r3
- mov r3, #SRAM_OFFSET2
- add r1, r1, r3
-next:
- ldmia r0!, {r3 - r10} @ copy from source address [r0]
- stmia r1!, {r3 - r10} @ copy to target address [r1]
- cmp r0, r2 @ until source end address [r2]
- bne next @ loop until equal */
-#if !defined(CONFIG_SYS_NAND_BOOT) && !defined(CONFIG_SYS_ONENAND_BOOT)
- /* No need to copy/exec the clock code - DPLL adjust already done
- * in NAND/oneNAND Boot.
- */
- bl cpy_clk_code @ put dpll adjust code behind vectors
-#endif /* NAND Boot */
-#endif
- /* the mask ROM code should have PLL and others stable */
-#ifndef CONFIG_SKIP_LOWLEVEL_INIT
- bl cpu_init_crit
-#endif
-
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
-relocate: @ relocate U-Boot to RAM
- adr r0, _start @ r0 <- current position of code
- ldr r1, _TEXT_BASE @ test if we run from flash or RAM
- cmp r0, r1 @ don't reloc during debug
- beq stack_setup
-
- ldr r2, _armboot_start
- ldr r3, _bss_start
- sub r2, r3, r2 @ r2 <- size of armboot
- add r2, r0, r2 @ r2 <- source end address
-
-copy_loop: @ copy 32 bytes at a time
- ldmia r0!, {r3 - r10} @ copy from source address [r0]
- stmia r1!, {r3 - r10} @ copy to target address [r1]
- cmp r0, r2 @ until source end address [r2]
- blo copy_loop
-#endif /* CONFIG_SKIP_RELOCATE_UBOOT */
-
- /* Set up the stack */
-stack_setup:
- ldr r0, _TEXT_BASE @ upper 128 KiB: relocated uboot
- sub r0, r0, #CONFIG_SYS_MALLOC_LEN @ malloc area
- sub r0, r0, #GENERATED_GBL_DATA_SIZE @ bdinfo
-#ifdef CONFIG_USE_IRQ
- sub r0, r0, #(CONFIG_STACKSIZE_IRQ + CONFIG_STACKSIZE_FIQ)
-#endif
- sub sp, r0, #12 @ leave 3 words for abort-stack
- bic sp, sp, #7 @ 8-byte alignment for ABI compliance
-
- /* Clear BSS (if any). Is below tx (watch load addr - need space) */
-clear_bss:
- ldr r0, _bss_start @ find start of bss segment
- ldr r1, _bss_end @ stop here
- mov r2, #0x00000000 @ clear value
-clbss_l:
- str r2, [r0] @ clear BSS location
- cmp r0, r1 @ are we at the end yet
- add r0, r0, #4 @ increment clear index pointer
- bne clbss_l @ keep clearing till at end
-
- ldr pc, _start_armboot @ jump to C code
-
-_start_armboot: .word start_armboot
-#endif /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
-
/*************************************************************************
*
* CPU_init_critical registers
@@ -464,14 +369,8 @@ cpu_init_crit:
@ user stack
stmia sp, {r0 - r12} @ Save user registers (now in
@ svc mode) r0-r12
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
- ldr r2, _armboot_start
- sub r2, r2, #(CONFIG_SYS_MALLOC_LEN)
- sub r2, r2, #(GENERATED_GBL_DATA_SIZE + 8) @ set base 2 words into abort
-#else
ldr r2, IRQ_STACK_START_IN @ set base 2 words into abort
@ stack
-#endif
ldmia r2, {r2 - r3} @ get values for "aborted" pc
@ and cpsr (into parm regs)
add r0, sp, #S_FRAME_SIZE @ grab pointer to old stack
@@ -507,14 +406,8 @@ cpu_init_crit:
.endm
.macro get_bad_stack
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
- ldr r13, _armboot_start @ setup our mode stack (enter
- sub r13, r13, #(CONFIG_SYS_MALLOC_LEN) @ move past malloc pool
- sub r13, r13, #(GENERATED_GBL_DATA_SIZE + 8) @ move to reserved a couple
-#else
ldr r13, IRQ_STACK_START_IN @ setup our mode stack (enter
@ in banked mode)
-#endif
str lr, [r13] @ save caller lr in position 0
@ of saved stack
@@ -535,14 +428,8 @@ cpu_init_crit:
sub r13, r13, #4 @ space on current stack for
@ scratch reg.
str r0, [r13] @ save R0's value.
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
- ldr r0, _armboot_start @ get data regions start
- sub r0, r0, #(CONFIG_SYS_MALLOC_LEN) @ move past malloc pool
- sub r0, r0, #(GENERATED_GBL_DATA_SIZE + 8) @ move past gbl and a couple
-#else
ldr r0, IRQ_STACK_START_IN @ get data regions start
@ spots for abort stack
-#endif
str lr, [r0] @ save caller lr in position 0
@ of saved stack
mrs r0, spsr @ get the spsr
diff --git a/arch/arm/cpu/ixp/start.S b/arch/arm/cpu/ixp/start.S
index a2560d4c2a..0269207bb2 100644
--- a/arch/arm/cpu/ixp/start.S
+++ b/arch/arm/cpu/ixp/start.S
@@ -98,12 +98,6 @@ _fiq: .word fiq
_TEXT_BASE:
.word CONFIG_SYS_TEXT_BASE
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
-.globl _armboot_start
-_armboot_start:
- .word _start
-#endif
-
/*
* These are defined in the board-specific linker script.
*/
@@ -127,7 +121,6 @@ FIQ_STACK_START:
.word 0x0badc0de
#endif
-#if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
/* IRQ stack memory (calculated at run-time) + 8 bytes */
.globl IRQ_STACK_START_IN
IRQ_STACK_START_IN:
@@ -394,190 +387,6 @@ clbss_l:str r2, [r0] /* clear loop... */
_board_init_r: .word board_init_r
-#else /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
-/****************************************************************************/
-/* */
-/* the actual reset code */
-/* */
-/****************************************************************************/
-
-reset:
- /* disable mmu, set big-endian */
- mov r0, #0xf8
- mcr p15, 0, r0, c1, c0, 0
- CPWAIT r0
-
- /* invalidate I & D caches & BTB */
- mcr p15, 0, r0, c7, c7, 0
- CPWAIT r0
-
- /* invalidate I & Data TLB */
- mcr p15, 0, r0, c8, c7, 0
- CPWAIT r0
-
- /* drain write and fill buffers */
- mcr p15, 0, r0, c7, c10, 4
- CPWAIT r0
-
- /* disable write buffer coalescing */
- mrc p15, 0, r0, c1, c0, 1
- orr r0, r0, #1
- mcr p15, 0, r0, c1, c0, 1
- CPWAIT r0
-
- /* set EXP CS0 to the optimum timing */
- ldr r1, =CONFIG_SYS_EXP_CS0
- ldr r2, =IXP425_EXP_CS0
- str r1, [r2]
-
- /* make sure flash is visible at 0 */
-#if 0
- ldr r2, =IXP425_EXP_CFG0
- ldr r1, [r2]
- orr r1, r1, #0x80000000
- str r1, [r2]
-#endif
- mov r1, #CONFIG_SYS_SDR_CONFIG
- ldr r2, =IXP425_SDR_CONFIG
- str r1, [r2]
-
- /* disable refresh cycles */
- mov r1, #0
- ldr r3, =IXP425_SDR_REFRESH
- str r1, [r3]
-
- /* send nop command */
- mov r1, #3
- ldr r4, =IXP425_SDR_IR
- str r1, [r4]
- DELAY_FOR 0x4000, r0
-
- /* set SDRAM internal refresh val */
- ldr r1, =CONFIG_SYS_SDRAM_REFRESH_CNT
- str r1, [r3]
- DELAY_FOR 0x4000, r0
-
- /* send precharge-all command to close all open banks */
- mov r1, #2
- str r1, [r4]
- DELAY_FOR 0x4000, r0
-
- /* provide 8 auto-refresh cycles */
- mov r1, #4
- mov r5, #8
-111: str r1, [r4]
- DELAY_FOR 0x100, r0
- subs r5, r5, #1
- bne 111b
-
- /* set mode register in sdram */
- mov r1, #CONFIG_SYS_SDR_MODE_CONFIG
- str r1, [r4]
- DELAY_FOR 0x4000, r0
-
- /* send normal operation command */
- mov r1, #6
- str r1, [r4]
- DELAY_FOR 0x4000, r0
-
- /* copy */
- mov r0, #0
- mov r4, r0
- add r2, r0, #CONFIG_SYS_MONITOR_LEN
- mov r1, #0x10000000
- mov r5, r1
-
- 30:
- ldr r3, [r0], #4
- str r3, [r1], #4
- cmp r0, r2
- bne 30b
-
- /* invalidate I & D caches & BTB */
- mcr p15, 0, r0, c7, c7, 0
- CPWAIT r0
-
- /* invalidate I & Data TLB */
- mcr p15, 0, r0, c8, c7, 0
- CPWAIT r0
-
- /* drain write and fill buffers */
- mcr p15, 0, r0, c7, c10, 4
- CPWAIT r0
-
- /* move flash to 0x50000000 */
- ldr r2, =IXP425_EXP_CFG0
- ldr r1, [r2]
- bic r1, r1, #0x80000000
- str r1, [r2]
-
- nop
- nop
- nop
- nop
- nop
- nop
-
- /* invalidate I & Data TLB */
- mcr p15, 0, r0, c8, c7, 0
- CPWAIT r0
-
- /* enable I cache */
- mrc p15, 0, r0, c1, c0, 0
- orr r0, r0, #MMU_Control_I
- mcr p15, 0, r0, c1, c0, 0
- CPWAIT r0
-
- mrs r0,cpsr /* set the cpu to SVC32 mode */
- bic r0,r0,#0x1f /* (superviser mode, M=10011) */
- orr r0,r0,#0x13
- msr cpsr,r0
-
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
-relocate: /* relocate U-Boot to RAM */
- adr r0, _start /* r0 <- current position of code */
- ldr r1, _TEXT_BASE /* test if we run from flash or RAM */
- cmp r0, r1 /* don't reloc during debug */
- beq stack_setup
-
- ldr r2, _armboot_start
- ldr r3, _bss_start
- sub r2, r3, r2 /* r2 <- size of armboot */
- add r2, r0, r2 /* r2 <- source end address */
-
-copy_loop:
- ldmia r0!, {r3-r10} /* copy from source address [r0] */
- stmia r1!, {r3-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- blo copy_loop
-#endif /* CONFIG_SKIP_RELOCATE_UBOOT */
-
- /* Set up the stack */
-stack_setup:
- ldr r0, _TEXT_BASE /* upper 128 KiB: relocated uboot */
- sub r0, r0, #CONFIG_SYS_MALLOC_LEN /* malloc area */
- sub r0, r0, #GENERATED_GBL_DATA_SIZE /* bdinfo */
-#ifdef CONFIG_USE_IRQ
- sub r0, r0, #(CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ)
-#endif
- sub sp, r0, #12 /* leave 3 words for abort-stack */
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
-
-clear_bss:
- ldr r0, _bss_start /* find start of bss segment */
- ldr r1, _bss_end /* stop here */
- mov r2, #0x00000000 /* clear */
-
-clbss_l:str r2, [r0] /* clear loop... */
- add r0, r0, #4
- cmp r0, r1
- blo clbss_l
-
- ldr pc, _start_armboot
-
-_start_armboot: .word start_armboot
-#endif /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
-
/****************************************************************************/
/* */
@@ -618,13 +427,7 @@ _start_armboot: .word start_armboot
stmia sp, {r0 - r12} /* Calling r0-r12 */
add r8, sp, #S_PC
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
- ldr r2, _armboot_start
- sub r2, r2, #(CONFIG_STACKSIZE+CONFIG_SYS_MALLOC_LEN)
- sub r2, r2, #(GENERATED_GBL_DATA_SIZE+8) @ set base 2 words into abort stack
-#else
ldr r2, IRQ_STACK_START_IN
-#endif
ldmia r2, {r2 - r4} /* get pc, cpsr, old_r0 */
add r0, sp, #S_FRAME_SIZE /* restore sp_SVC */
@@ -659,13 +462,7 @@ _start_armboot: .word start_armboot
.endm
.macro get_bad_stack
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
- ldr r13, _armboot_start @ setup our mode stack
- sub r13, r13, #(CONFIG_STACKSIZE+CONFIG_SYS_MALLOC_LEN)
- sub r13, r13, #(GENERATED_GBL_DATA_SIZE+8) @ reserved a couple spots in abort stack
-#else
ldr r13, IRQ_STACK_START_IN @ setup our mode stack
-#endif
str lr, [r13] @ save caller lr / spsr
mrs lr, spsr
diff --git a/arch/arm/cpu/lh7a40x/start.S b/arch/arm/cpu/lh7a40x/start.S
index 239ad47a4f..080d29d20b 100644
--- a/arch/arm/cpu/lh7a40x/start.S
+++ b/arch/arm/cpu/lh7a40x/start.S
@@ -75,12 +75,6 @@ _fiq: .word fiq
_TEXT_BASE:
.word CONFIG_SYS_TEXT_BASE
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
-.globl _armboot_start
-_armboot_start:
- .word _start
-#endif
-
/*
* These are defined in the board-specific linker script.
*/
@@ -104,7 +98,6 @@ FIQ_STACK_START:
.word 0x0badc0de
#endif
-#if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
/* IRQ stack memory (calculated at run-time) + 8 bytes */
.globl IRQ_STACK_START_IN
IRQ_STACK_START_IN:
@@ -278,100 +271,6 @@ clbss_l:str r2, [r0] /* clear loop... */
_board_init_r: .word board_init_r
-#else /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
-/*
- * the actual reset code
- */
-
-reset:
- /*
- * set the cpu to SVC32 mode
- */
- mrs r0,cpsr
- bic r0,r0,#0x1f
- orr r0,r0,#0xd3
- msr cpsr,r0
-
-#define pWDTCTL 0x80001400 /* Watchdog Timer control register */
-#define pINTENC 0x8000050C /* Interupt-Controller enable clear register */
-#define pCLKSET 0x80000420 /* clock divisor register */
-
- /* disable watchdog, set watchdog control register to
- * all zeros (default reset)
- */
- ldr r0, =pWDTCTL
- mov r1, #0x0
- str r1, [r0]
-
- /*
- * mask all IRQs by setting all bits in the INTENC register (default)
- */
- mov r1, #0xffffffff
- ldr r0, =pINTENC
- str r1, [r0]
-
- /* FCLK:HCLK:PCLK = 1:2:2 */
- /* default FCLK is 200 MHz, using 14.7456 MHz fin */
- ldr r0, =pCLKSET
- ldr r1, =0x0004ee39
-@ ldr r1, =0x0005ee39 @ 1: 2: 4
- str r1, [r0]
-
- /*
- * we do sys-critical inits only at reboot,
- * not when booting from ram!
- */
-#ifndef CONFIG_SKIP_LOWLEVEL_INIT
- bl cpu_init_crit
-#endif
-
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
-relocate: /* relocate U-Boot to RAM */
- adr r0, _start /* r0 <- current position of code */
- ldr r1, _TEXT_BASE /* test if we run from flash or RAM */
- cmp r0, r1 /* don't reloc during debug */
- beq stack_setup
-
- ldr r2, _armboot_start
- ldr r3, _bss_start
- sub r2, r3, r2 /* r2 <- size of armboot */
- add r2, r0, r2 /* r2 <- source end address */
-
-copy_loop:
- ldmia r0!, {r3-r10} /* copy from source address [r0] */
- stmia r1!, {r3-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- blo copy_loop
-#endif /* CONFIG_SKIP_RELOCATE_UBOOT */
-
- /* Set up the stack */
-stack_setup:
- ldr r0, _TEXT_BASE /* upper 128 KiB: relocated uboot */
- sub r0, r0, #CONFIG_SYS_MALLOC_LEN /* malloc area */
- sub r0, r0, #GENERATED_GBL_DATA_SIZE /* bdinfo */
-#ifdef CONFIG_USE_IRQ
- sub r0, r0, #(CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ)
-#endif
- sub sp, r0, #12 /* leave 3 words for abort-stack */
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
-
-clear_bss:
- ldr r0, _bss_start /* find start of bss segment */
- @add r0, r0, #4 /* start at first byte of bss */
- /* why inc. 4 bytes past then? */
- ldr r1, _bss_end /* stop here */
- mov r2, #0x00000000 /* clear */
-
-clbss_l:str r2, [r0] /* clear loop... */
- add r0, r0, #4
- cmp r0, r1
- blo clbss_l
-
- ldr pc, _start_armboot
-
-_start_armboot: .word start_armboot
-#endif /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
-
/*
*************************************************************************
*
@@ -460,13 +359,7 @@ cpu_init_crit:
.macro bad_save_user_regs
sub sp, sp, #S_FRAME_SIZE
stmia sp, {r0 - r12} @ Calling r0-r12
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
- ldr r2, _armboot_start
- sub r2, r2, #(CONFIG_STACKSIZE+CONFIG_SYS_MALLOC_LEN)
- sub r2, r2, #(GENERATED_GBL_DATA_SIZE+8) @ set base 2 words into abort stack
-#else
ldr r2, IRQ_STACK_START_IN
-#endif
ldmia r2, {r2 - r3} @ get pc, cpsr
add r0, sp, #S_FRAME_SIZE @ restore sp_SVC
@@ -497,13 +390,7 @@ cpu_init_crit:
.endm
.macro get_bad_stack
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
- ldr r13, _armboot_start @ setup our mode stack
- sub r13, r13, #(CONFIG_STACKSIZE+CONFIG_SYS_MALLOC_LEN)
- sub r13, r13, #(GENERATED_GBL_DATA_SIZE+8) @ reserved a couple spots in abort stack
-#else
ldr r13, IRQ_STACK_START_IN @ setup our mode stack
-#endif
str lr, [r13] @ save caller lr / spsr
mrs lr, spsr
diff --git a/arch/arm/cpu/pxa/start.S b/arch/arm/cpu/pxa/start.S
index bf8510eb76..03cf4dec36 100644
--- a/arch/arm/cpu/pxa/start.S
+++ b/arch/arm/cpu/pxa/start.S
@@ -299,7 +299,7 @@ fixnext:
add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
cmp r2, r3
blo fixloop
-#endif
+#endif /* #ifndef CONFIG_PRELOADER */
#endif /* #ifndef CONFIG_SKIP_RELOCATE_UBOOT */
clear_bss:
@@ -316,7 +316,7 @@ clbss_l:str r2, [r0] /* clear loop... */
add r0, r0, #4
cmp r0, r1
bne clbss_l
-#endif
+#endif /* #ifndef CONFIG_PRELOADER */
/*
* We are done. Do not return, instead branch to second part of board
@@ -343,7 +343,7 @@ _start_oneboot_ofs
_board_init_r_ofs:
.word board_init_r - _start
-#endif
+#endif /* CONFIG_ONENAND_IPL */
_rel_dyn_start_ofs:
.word __rel_dyn_start - _start
@@ -352,7 +352,7 @@ _rel_dyn_end_ofs:
_dynsym_start_ofs:
.word __dynsym_start - _start
-#else /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
+#else /* CONFIG_PRELOADER */
/****************************************************************************/
/* */
@@ -377,7 +377,7 @@ reset:
/* Start OneNAND IPL */
ldr pc, =start_oneboot
-#endif /* #if !defined(CONFIG_ONENAND_IPL) */
+#endif /* CONFIG_PRELOADER */
#ifndef CONFIG_PRELOADER
/****************************************************************************/
@@ -419,13 +419,7 @@ reset:
stmia sp, {r0 - r12} /* Calling r0-r12 */
add r8, sp, #S_PC
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
- ldr r2, _armboot_start
- sub r2, r2, #(CONFIG_STACKSIZE+CONFIG_SYS_MALLOC_LEN)
- sub r2, r2, #(GENERATED_GBL_DATA_SIZE+8) @ set base 2 words into abort stack
-#else
ldr r2, IRQ_STACK_START_IN
-#endif
ldmia r2, {r2 - r4} /* get pc, cpsr, old_r0 */
add r0, sp, #S_FRAME_SIZE /* restore sp_SVC */
@@ -460,13 +454,7 @@ reset:
.endm
.macro get_bad_stack
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
- ldr r13, _armboot_start @ setup our mode stack
- sub r13, r13, #(CONFIG_STACKSIZE+CONFIG_SYS_MALLOC_LEN)
- sub r13, r13, #(GENERATED_GBL_DATA_SIZE+8) @ reserved a couple spots in abort stack
-#else
ldr r13, IRQ_STACK_START_IN @ setup our mode stack
-#endif
str lr, [r13] @ save caller lr / spsr
mrs lr, spsr
@@ -485,7 +473,7 @@ reset:
.macro get_fiq_stack @ setup FIQ stack
ldr sp, FIQ_STACK_START
.endm
-#endif /* CONFIG_PRELOADER */
+#endif /* CONFIG_PRELOADER
/****************************************************************************/
@@ -499,7 +487,7 @@ reset:
do_hang:
ldr sp, _TEXT_BASE /* use 32 words abort stack */
bl hang /* hang and never return */
-#else /* !CONFIG_PRELOADER */
+#else
.align 5
undefined_instruction:
get_bad_stack
@@ -618,4 +606,4 @@ mmu_table:
.word (__base << 20) | 0xc12
.set __base, __base + 1
.endr
-#endif
+#endif /* CONFIG_PRELOADER */
diff --git a/arch/arm/cpu/s3c44b0/start.S b/arch/arm/cpu/s3c44b0/start.S
index c58da98798..ca95dea552 100644
--- a/arch/arm/cpu/s3c44b0/start.S
+++ b/arch/arm/cpu/s3c44b0/start.S
@@ -66,12 +66,6 @@ _start: b reset
_TEXT_BASE:
.word CONFIG_SYS_TEXT_BASE
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
-.globl _armboot_start
-_armboot_start:
- .word _start
-#endif
-
/*
* These are defined in the board-specific linker script.
*/
@@ -95,7 +89,6 @@ FIQ_STACK_START:
.word 0x0badc0de
#endif
-#if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
/* IRQ stack memory (calculated at run-time) + 8 bytes */
.globl IRQ_STACK_START_IN
IRQ_STACK_START_IN:
@@ -265,84 +258,6 @@ clbss_l:str r2, [r0] /* clear loop... */
_board_init_r: .word board_init_r
-#else /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
-/*
- * the actual reset code
- */
-
-reset:
- /*
- * set the cpu to SVC32 mode
- */
- mrs r0,cpsr
- bic r0,r0,#0x1f
- orr r0,r0,#0x13
- msr cpsr,r0
-
- /*
- * we do sys-critical inits only at reboot,
- * not when booting from ram!
- */
-
-#ifndef CONFIG_SKIP_LOWLEVEL_INIT
- bl cpu_init_crit
- /*
- * before relocating, we have to setup RAM timing
- * because memory timing is board-dependend, you will
- * find a lowlevel_init.S in your board directory.
- */
- bl lowlevel_init
-#endif
-
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
-relocate: /* relocate U-Boot to RAM */
- adr r0, _start /* r0 <- current position of code */
- ldr r1, _TEXT_BASE /* test if we run from flash or RAM */
- cmp r0, r1 /* don't reloc during debug */
- beq stack_setup
-
- ldr r2, _armboot_start
- ldr r3, _bss_start
- sub r2, r3, r2 /* r2 <- size of armboot */
- add r2, r0, r2 /* r2 <- source end address */
-
-copy_loop:
- ldmia r0!, {r3-r10} /* copy from source address [r0] */
- stmia r1!, {r3-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- blo copy_loop
-
-/*
- now copy to sram the interrupt vector
-*/
- adr r0, real_vectors
- add r2, r0, #1024
- ldr r1, =0x0c000000
- add r1, r1, #0x08
-vector_copy_loop:
- ldmia r0!, {r3-r10}
- stmia r1!, {r3-r10}
- cmp r0, r2
- blo vector_copy_loop
-#endif /* CONFIG_SKIP_RELOCATE_UBOOT */
-
- /* Set up the stack */
-stack_setup:
- ldr r0, _TEXT_BASE /* upper 128 KiB: relocated uboot */
- sub r0, r0, #CONFIG_SYS_MALLOC_LEN /* malloc area */
- sub r0, r0, #GENERATED_GBL_DATA_SIZE /* bdinfo */
-#ifdef CONFIG_USE_IRQ
- sub r0, r0, #(CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ)
-#endif
- sub sp, r0, #12 /* leave 3 words for abort-stack */
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
-
- ldr pc, _start_armboot
-
-_start_armboot: .word start_armboot
-
-#endif /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
-
/*
*************************************************************************
*
diff --git a/arch/arm/cpu/sa1100/start.S b/arch/arm/cpu/sa1100/start.S
index e6afe0f86f..ab6e2f2194 100644
--- a/arch/arm/cpu/sa1100/start.S
+++ b/arch/arm/cpu/sa1100/start.S
@@ -76,12 +76,6 @@ _fiq: .word fiq
_TEXT_BASE:
.word CONFIG_SYS_TEXT_BASE
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
-.globl _armboot_start
-_armboot_start:
- .word _start
-#endif
-
/*
* These are defined in the board-specific linker script.
*/
@@ -105,7 +99,6 @@ FIQ_STACK_START:
.word 0x0badc0de
#endif
-#if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
/* IRQ stack memory (calculated at run-time) + 8 bytes */
.globl IRQ_STACK_START_IN
IRQ_STACK_START_IN:
@@ -254,75 +247,6 @@ clbss_l:str r2, [r0] /* clear loop... */
_board_init_r: .word board_init_r
-#else /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
-
-/*
- * the actual reset code
- */
-
-reset:
- /*
- * set the cpu to SVC32 mode
- */
- mrs r0,cpsr
- bic r0,r0,#0x1f
- orr r0,r0,#0x13
- msr cpsr,r0
-
- /*
- * we do sys-critical inits only at reboot,
- * not when booting from ram!
- */
-#ifndef CONFIG_SKIP_LOWLEVEL_INIT
- bl cpu_init_crit
-#endif
-
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
-relocate: /* relocate U-Boot to RAM */
- adr r0, _start /* r0 <- current position of code */
- ldr r1, _TEXT_BASE /* test if we run from flash or RAM */
- cmp r0, r1 /* don't reloc during debug */
- beq stack_setup
-
- ldr r2, _armboot_start
- ldr r3, _bss_start
- sub r2, r3, r2 /* r2 <- size of armboot */
- add r2, r0, r2 /* r2 <- source end address */
-
-copy_loop:
- ldmia r0!, {r3-r10} /* copy from source address [r0] */
- stmia r1!, {r3-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- blo copy_loop
-#endif /* CONFIG_SKIP_RELOCATE_UBOOT */
-
- /* Set up the stack */
-stack_setup:
- ldr r0, _TEXT_BASE /* upper 128 KiB: relocated uboot */
- sub r0, r0, #CONFIG_SYS_MALLOC_LEN /* malloc area */
- sub r0, r0, #GENERATED_GBL_DATA_SIZE /* bdinfo */
-#ifdef CONFIG_USE_IRQ
- sub r0, r0, #(CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ)
-#endif
- sub sp, r0, #12 /* leave 3 words for abort-stack */
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
-
-clear_bss:
- ldr r0, _bss_start /* find start of bss segment */
- ldr r1, _bss_end /* stop here */
- mov r2, #0x00000000 /* clear */
-
-clbss_l:str r2, [r0] /* clear loop... */
- add r0, r0, #4
- cmp r0, r1
- blo clbss_l
-
- ldr pc, _start_armboot
-
-_start_armboot: .word start_armboot
-
-#endif /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
-
/*
*************************************************************************
*
@@ -441,13 +365,7 @@ cpu_init_crit:
stmia sp, {r0 - r12} @ Calling r0-r12
add r8, sp, #S_PC
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
- ldr r2, _armboot_start
- sub r2, r2, #(CONFIG_STACKSIZE+CONFIG_SYS_MALLOC_LEN)
- sub r2, r2, #(GENERATED_GBL_DATA_SIZE+8) @ set base 2 words into abort stack
-#else
ldr r2, IRQ_STACK_START_IN
-#endif
ldmia r2, {r2 - r4} @ get pc, cpsr, old_r0
add r0, sp, #S_FRAME_SIZE @ restore sp_SVC
@@ -478,13 +396,7 @@ cpu_init_crit:
.endm
.macro get_bad_stack
-#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
- ldr r13, _armboot_start @ setup our mode stack
- sub r13, r13, #(CONFIG_STACKSIZE+CONFIG_SYS_MALLOC_LEN)
- sub r13, r13, #(GENERATED_GBL_DATA_SIZE+8) @ reserved a couple spots in abort stack
-#else
ldr r13, IRQ_STACK_START_IN @ setup our mode stack
-#endif
str lr, [r13] @ save caller lr / spsr
mrs lr, spsr