diff options
Diffstat (limited to 'arch/x86/include/asm')
| -rw-r--r-- | arch/x86/include/asm/intel_pinctrl.h | 306 | ||||
| -rw-r--r-- | arch/x86/include/asm/intel_pinctrl_defs.h | 373 |
2 files changed, 679 insertions, 0 deletions
diff --git a/arch/x86/include/asm/intel_pinctrl.h b/arch/x86/include/asm/intel_pinctrl.h new file mode 100644 index 0000000000..72fd9246cb --- /dev/null +++ b/arch/x86/include/asm/intel_pinctrl.h @@ -0,0 +1,306 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (C) 2017 Intel Corporation. + * Copyright 2019 Google LLC + * + * Modified from coreboot gpio.h + */ + +#ifndef __ASM_INTEL_PINCTRL_H +#define __ASM_INTEL_PINCTRL_H + +#include <dm/pinctrl.h> + +/** + * struct pad_config - config for a pad + * @pad: offset of pad within community + * @pad_config: Pad config data corresponding to DW0, DW1, etc. + */ +struct pad_config { + int pad; + u32 pad_config[4]; +}; + +#include <asm/arch/gpio.h> + +/* GPIO community IOSF sideband clock gating */ +#define MISCCFG_GPSIDEDPCGEN BIT(5) +/* GPIO community RCOMP clock gating */ +#define MISCCFG_GPRCOMPCDLCGEN BIT(4) +/* GPIO community RTC clock gating */ +#define MISCCFG_GPRTCDLCGEN BIT(3) +/* GFX controller clock gating */ +#define MISCCFG_GSXSLCGEN BIT(2) +/* GPIO community partition clock gating */ +#define MISCCFG_GPDPCGEN BIT(1) +/* GPIO community local clock gating */ +#define MISCCFG_GPDLCGEN BIT(0) +/* Enable GPIO community power management configuration */ +#define MISCCFG_ENABLE_GPIO_PM_CONFIG (MISCCFG_GPSIDEDPCGEN | \ + MISCCFG_GPRCOMPCDLCGEN | MISCCFG_GPRTCDLCGEN | MISCCFG_GSXSLCGEN \ + | MISCCFG_GPDPCGEN | MISCCFG_GPDLCGEN) + +/* + * GPIO numbers may not be contiguous and instead will have a different + * starting pin number for each pad group. + */ +#define INTEL_GPP_BASE(first_of_community, start_of_group, end_of_group,\ + group_pad_base) \ + { \ + .first_pad = (start_of_group) - (first_of_community), \ + .size = (end_of_group) - (start_of_group) + 1, \ + .acpi_pad_base = (group_pad_base), \ + } + +/* + * A pad base of -1 indicates that this group uses contiguous numbering + * and a pad base should not be used for this group. + */ +#define PAD_BASE_NONE -1 + +/* The common/default group numbering is contiguous */ +#define INTEL_GPP(first_of_community, start_of_group, end_of_group) \ + INTEL_GPP_BASE(first_of_community, start_of_group, end_of_group,\ + PAD_BASE_NONE) + +/** + * struct reset_mapping - logical to actual value for PADRSTCFG in DW0 + * + * Note that the values are expected to be within the field placement of the + * register itself. i.e. if the reset field is at 31:30 then the values within + * logical and chipset should occupy 31:30. + */ +struct reset_mapping { + u32 logical; + u32 chipset; +}; + +/** + * struct pad_group - describes the groups within each community + * + * @first_pad: offset of first pad of the group relative to the community + * @size: size of the group + * @acpi_pad_base: starting pin number for the pads in this group when they are + * used in ACPI. This is only needed if the pins are not contiguous across + * groups. Most groups will have this set to PAD_BASE_NONE and use + * contiguous numbering for ACPI. + */ +struct pad_group { + int first_pad; + uint size; + int acpi_pad_base; +}; + +/** + * struct pad_community - community of pads + * + * This describes a community, or each group within a community when multiple + * groups exist inside a community + * + * @name: Community name + * @acpi_path: ACPI path + * @num_gpi_regs: number of gpi registers in community + * @max_pads_per_group: number of pads in each group; number of pads bit-mapped + * in each GPI status/en and Host Own Reg + * @first_pad: first pad in community + * @last_pad: last pad in community + * @host_own_reg_0: offset to Host Ownership Reg 0 + * @gpi_int_sts_reg_0: offset to GPI Int STS Reg 0 + * @gpi_int_en_reg_0: offset to GPI Int Enable Reg 0 + * @gpi_smi_sts_reg_0: offset to GPI SMI STS Reg 0 + * @gpi_smi_en_reg_0: offset to GPI SMI EN Reg 0 + * @pad_cfg_base: offset to first PAD_GFG_DW0 Reg + * @gpi_status_offset: specifies offset in struct gpi_status + * @port: PCR Port ID + * @reset_map: PADRSTCFG logical to chipset mapping + * @num_reset_vals: number of values in @reset_map + * @groups; list of groups for this community + * @num_groups: number of groups + */ +struct pad_community { + const char *name; + const char *acpi_path; + size_t num_gpi_regs; + size_t max_pads_per_group; + uint first_pad; + uint last_pad; + u16 host_own_reg_0; + u16 gpi_int_sts_reg_0; + u16 gpi_int_en_reg_0; + u16 gpi_smi_sts_reg_0; + u16 gpi_smi_en_reg_0; + u16 pad_cfg_base; + u8 gpi_status_offset; + u8 port; + const struct reset_mapping *reset_map; + size_t num_reset_vals; + const struct pad_group *groups; + size_t num_groups; +}; + +/** + * struct intel_pinctrl_priv - private data for each pinctrl device + * + * @comm: Pad community for this device + * @num_cfgs: Number of configuration words for each pad + * @itss: ITSS device (for interrupt handling) + * @itss_pol_cfg: Use to program Interrupt Polarity Control (IPCx) register + * Each bit represents IRQx Active High Polarity Disable configuration: + * when set to 1, the interrupt polarity associated with IRQx is inverted + * to appear as Active Low to IOAPIC and vice versa + */ +struct intel_pinctrl_priv { + const struct pad_community *comm; + int num_cfgs; + struct udevice *itss; + bool itss_pol_cfg; +}; + +/* Exported common operations for the pinctrl driver */ +extern const struct pinctrl_ops intel_pinctrl_ops; + +/* Exported common probe function for the pinctrl driver */ +int intel_pinctrl_probe(struct udevice *dev); + +/** + * intel_pinctrl_ofdata_to_platdata() - Handle common platdata setup + * + * @dev: Pinctrl device + * @comm: Pad community for this device + * @num_cfgs: Number of configuration words for each pad + * @return 0 if OK, -EDOM if @comm is NULL, other -ve value on other error + */ +int intel_pinctrl_ofdata_to_platdata(struct udevice *dev, + const struct pad_community *comm, + int num_cfgs); + +/** + * pinctrl_route_gpe() - set GPIO groups for the general-purpose-event blocks + * + * The values from PMC register GPE_CFG are passed which is then mapped to + * proper groups for MISCCFG. This basically sets the MISCCFG register bits: + * dw0 = gpe0_route[11:8]. This is ACPI GPE0b. + * dw1 = gpe0_route[15:12]. This is ACPI GPE0c. + * dw2 = gpe0_route[19:16]. This is ACPI GPE0d. + * + * @dev: ITSS device + * @gpe0b: Value for GPE0B + * @gpe0c: Value for GPE0C + * @gpe0d: Value for GPE0D + * @return 0 if OK, -ve on error + */ +int pinctrl_route_gpe(struct udevice *dev, uint gpe0b, uint gpe0c, uint gpe0d); + +/** + * pinctrl_config_pads() - Configure a list of pads + * + * Configures multiple pads using the provided data from the device tree. + * + * @dev: pinctrl device (any will do) + * @pads: Pad data, consisting of a pad number followed by num_cfgs entries + * containing the data for that pad (num_cfgs is set by the pinctrl device) + * @pads_count: Number of pads to configure + * @return 0 if OK, -ve on error + */ +int pinctrl_config_pads(struct udevice *dev, u32 *pads, int pads_count); + +/** + * pinctrl_gpi_clear_int_cfg() - Set up the interrupts for use + * + * This enables the interrupt inputs and clears the status register bits + * + * @return 0 if OK, -ve on error + */ +int pinctrl_gpi_clear_int_cfg(void); + +/** + * pinctrl_config_pads_for_node() - Configure pads + * + * Set up the pads using the data in a given node + * + * @dev: pinctrl device (any will do) + * @node: Node containing the 'pads' property with the data in it + * @return 0 if OK, -ve on error + */ +int pinctrl_config_pads_for_node(struct udevice *dev, ofnode node); + +/** + * pinctrl_read_pads() - Read pad data from a node + * + * @dev: pinctrl device (any will do, it is just used to get config) + * @node: Node to read pad data from + * @prop: Property name to use (e.g. "pads") + * @padsp: Returns a pointer to an allocated array of pad data, in the format: + * <pad> + * <pad_config0> + * <pad_config1> + * ... + * + * The number of pad config values is set by the pinctrl controller. + * The caller must free this array. + * @pad_countp: Returns the number of pads read + * @ereturn 0 if OK, -ve on error + */ +int pinctrl_read_pads(struct udevice *dev, ofnode node, const char *prop, + u32 **padsp, int *pad_countp); + +/** + * pinctrl_count_pads() - Count the number of pads in a pad array + * + * This used used with of-platdata where the array may be smaller than its + * maximum size. This function searches for the last pad in the array by finding + * the first 'zero' record + * + * This works out the number of records in the array. Each record has one word + * for the pad and num_cfgs words for the config. + * + * @dev: pinctrl device (any will do) + * @pads: Array of pad data + * @size: Size of pad data in bytes + * @return number of pads represented by the data + */ +int pinctrl_count_pads(struct udevice *dev, u32 *pads, int size); + +/** + * intel_pinctrl_get_config_reg_addr() - Get address of the pin config registers + * + * @dev: Pinctrl device + * @offset: GPIO offset within this device + * @return register offset within the GPIO p2sb region + */ +u32 intel_pinctrl_get_config_reg_addr(struct udevice *dev, uint offset); + +/** + * intel_pinctrl_get_config_reg() - Get the value of a GPIO register + * + * @dev: Pinctrl device + * @offset: GPIO offset within this device + * @return register value within the GPIO p2sb region + */ +u32 intel_pinctrl_get_config_reg(struct udevice *dev, uint offset); + +/** + * intel_pinctrl_get_pad() - Get pad information for a pad + * + * This is used by the GPIO controller to find the pinctrl used by a pad. + * + * @pad: Pad to check + * @devp: Returns pinctrl device containing that pad + * @offsetp: Returns offset of pad within that pinctrl device + */ +int intel_pinctrl_get_pad(uint pad, struct udevice **devp, uint *offsetp); + +/** + * intel_pinctrl_get_acpi_pin() - Get the ACPI pin for a pinctrl pin + * + * Maps a pinctrl pin (in terms of its offset within the pins controlled by that + * pinctrl) to an ACPI GPIO pin-table entry. + * + * @dev: Pinctrl device to check + * @offset: Offset of pin within that device (0 = first) + * @return associated ACPI GPIO pin-table entry, or standard pin number if the + * ACPI pad base is not set + */ +int intel_pinctrl_get_acpi_pin(struct udevice *dev, uint offset); + +#endif diff --git a/arch/x86/include/asm/intel_pinctrl_defs.h b/arch/x86/include/asm/intel_pinctrl_defs.h new file mode 100644 index 0000000000..6da06bb52b --- /dev/null +++ b/arch/x86/include/asm/intel_pinctrl_defs.h @@ -0,0 +1,373 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2015-2016 Intel Corp. + * Copyright 2019 Google LLC + * + * Modified from coreboot gpio_defs.h + */ + +#ifndef _ASM_INTEL_PINCTRL_DEFS_H_ +#define _ASM_INTEL_PINCTRL_DEFS_H_ + +/* This file is included by device trees, so avoid BIT() macros */ + +#define PAD_CFG0_TX_STATE_BIT 0 +#define PAD_CFG0_TX_STATE (1 << PAD_CFG0_TX_STATE_BIT) +#define PAD_CFG0_RX_STATE_BIT 1 +#define PAD_CFG0_RX_STATE (1 << PAD_CFG0_RX_STATE_BIT) +#define PAD_CFG0_TX_DISABLE (1 << 8) +#define PAD_CFG0_RX_DISABLE (1 << 9) + +#define PAD_CFG0_MODE_SHIFT 10 +#define PAD_CFG0_MODE_MASK (7 << PAD_CFG0_MODE_SHIFT) +#define PAD_CFG0_MODE_GPIO (0 << PAD_CFG0_MODE_SHIFT) +#define PAD_CFG0_MODE_NF1 (1 << PAD_CFG0_MODE_SHIFT) +#define PAD_CFG0_MODE_NF2 (2 << PAD_CFG0_MODE_SHIFT) +#define PAD_CFG0_MODE_NF3 (3 << PAD_CFG0_MODE_SHIFT) +#define PAD_CFG0_MODE_NF4 (4 << PAD_CFG0_MODE_SHIFT) +#define PAD_CFG0_MODE_NF5 (5 << PAD_CFG0_MODE_SHIFT) +#define PAD_CFG0_MODE_NF6 (6 << PAD_CFG0_MODE_SHIFT) + +#define PAD_CFG0_ROUTE_MASK (0xf << 17) +#define PAD_CFG0_ROUTE_NMI (1 << 17) +#define PAD_CFG0_ROUTE_SMI (1 << 18) +#define PAD_CFG0_ROUTE_SCI (1 << 19) +#define PAD_CFG0_ROUTE_IOAPIC (1 << 20) +#define PAD_CFG0_RXTENCFG_MASK (3 << 21) +#define PAD_CFG0_RXINV_MASK (1 << 23) +#define PAD_CFG0_RX_POL_INVERT (1 << 23) +#define PAD_CFG0_RX_POL_NONE (0 << 23) +#define PAD_CFG0_PREGFRXSEL (1 << 24) +#define PAD_CFG0_TRIG_MASK (3 << 25) +#define PAD_CFG0_TRIG_LEVEL (0 << 25) +#define PAD_CFG0_TRIG_EDGE_SINGLE (1 << 25) /* controlled by RX_INVERT*/ +#define PAD_CFG0_TRIG_OFF (2 << 25) +#define PAD_CFG0_TRIG_EDGE_BOTH (3 << 25) +#define PAD_CFG0_RXRAW1_MASK (1 << 28) +#define PAD_CFG0_RXPADSTSEL_MASK (1 << 29) +#define PAD_CFG0_RESET_MASK (3 << 30) +#define PAD_CFG0_LOGICAL_RESET_PWROK (0U << 30) +#define PAD_CFG0_LOGICAL_RESET_DEEP (1U << 30) +#define PAD_CFG0_LOGICAL_RESET_PLTRST (2U << 30) +#define PAD_CFG0_LOGICAL_RESET_RSMRST (3U << 30) + +/* + * Use the fourth bit in IntSel field to indicate gpio ownership. This field is + * RO and hence not used during gpio configuration. + */ +#define PAD_CFG1_GPIO_DRIVER (0x1 << 4) +#define PAD_CFG1_IRQ_MASK (0xff << 0) +#define PAD_CFG1_IOSTERM_MASK (0x3 << 8) +#define PAD_CFG1_IOSTERM_SAME (0x0 << 8) +#define PAD_CFG1_IOSTERM_DISPUPD (0x1 << 8) +#define PAD_CFG1_IOSTERM_ENPD (0x2 << 8) +#define PAD_CFG1_IOSTERM_ENPU (0x3 << 8) +#define PAD_CFG1_PULL_MASK (0xf << 10) +#define PAD_CFG1_PULL_NONE (0x0 << 10) +#define PAD_CFG1_PULL_DN_5K (0x2 << 10) +#define PAD_CFG1_PULL_DN_20K (0x4 << 10) +#define PAD_CFG1_PULL_UP_1K (0x9 << 10) +#define PAD_CFG1_PULL_UP_5K (0xa << 10) +#define PAD_CFG1_PULL_UP_2K (0xb << 10) +#define PAD_CFG1_PULL_UP_20K (0xc << 10) +#define PAD_CFG1_PULL_UP_667 (0xd << 10) +#define PAD_CFG1_PULL_NATIVE (0xf << 10) + +/* Tx enabled driving last value driven, Rx enabled */ +#define PAD_CFG1_IOSSTATE_TX_LAST_RXE (0x0 << 14) +/* + * Tx enabled driving 0, Rx disabled and Rx driving 0 back to its controller + * internally + */ +#define PAD_CFG1_IOSSTATE_TX0_RX_DCR_X0 (0x1 << 14) +/* + * Tx enabled driving 0, Rx disabled and Rx driving 1 back to its controller + * internally + */ +#define PAD_CFG1_IOSSTATE_TX0_RX_DCR_X1 (0x2 << 14) +/* + * Tx enabled driving 1, Rx disabled and Rx driving 0 back to its controller + * internally + */ +#define PAD_CFG1_IOSSTATE_TX1_RX_DCR_X0 (0x3 << 14) +/* + * Tx enabled driving 1, Rx disabled and Rx driving 1 back to its controller + * internally + */ +#define PAD_CFG1_IOSSTATE_TX1_RX_DCR_X1 (0x4 << 14) +/* Tx enabled driving 0, Rx enabled */ +#define PAD_CFG1_IOSSTATE_TX0_RXE (0x5 << 14) +/* Tx enabled driving 1, Rx enabled */ +#define PAD_CFG1_IOSSTATE_TX1_RXE (0x6 << 14) +/* Hi-Z, Rx driving 0 back to its controller internally */ +#define PAD_CFG1_IOSSTATE_HIZCRX0 (0x7 << 14) +/* Hi-Z, Rx driving 1 back to its controller internally */ +#define PAD_CFG1_IOSSTATE_HIZCRX1 (0x8 << 14) +/* Tx disabled, Rx enabled */ +#define PAD_CFG1_IOSSTATE_TXD_RXE (0x9 << 14) +#define PAD_CFG1_IOSSTATE_IGNORE (0xf << 14) /* Ignore Iostandby */ +/* mask to extract Iostandby bits */ +#define PAD_CFG1_IOSSTATE_MASK (0xf << 14) +#define PAD_CFG1_IOSSTATE_SHIFT 14 /* set Iostandby bits [17:14] */ + +#define PAD_CFG2_DEBEN 1 +/* Debounce Duration = (2 ^ PAD_CFG2_DEBOUNCE_x_RTC) * RTC clock duration */ +#define PAD_CFG2_DEBOUNCE_8_RTC (0x3 << 1) +#define PAD_CFG2_DEBOUNCE_16_RTC (0x4 << 1) +#define PAD_CFG2_DEBOUNCE_32_RTC (0x5 << 1) +#define PAD_CFG2_DEBOUNCE_64_RTC (0x6 << 1) +#define PAD_CFG2_DEBOUNCE_128_RTC (0x7 << 1) +#define PAD_CFG2_DEBOUNCE_256_RTC (0x8 << 1) +#define PAD_CFG2_DEBOUNCE_512_RTC (0x9 << 1) +#define PAD_CFG2_DEBOUNCE_1K_RTC (0xa << 1) +#define PAD_CFG2_DEBOUNCE_2K_RTC (0xb << 1) +#define PAD_CFG2_DEBOUNCE_4K_RTC (0xc << 1) +#define PAD_CFG2_DEBOUNCE_8K_RTC (0xd << 1) +#define PAD_CFG2_DEBOUNCE_16K_RTC (0xe << 1) +#define PAD_CFG2_DEBOUNCE_32K_RTC (0xf << 1) +#define PAD_CFG2_DEBOUNCE_MASK 0x1f + +/* voltage tolerance 0=3.3V default 1=1.8V tolerant */ +#if IS_ENABLED(INTEL_PINCTRL_IOSTANDBY) +#define PAD_CFG1_TOL_MASK (0x1 << 25) +#define PAD_CFG1_TOL_1V8 (0x1 << 25) +#endif + +#define PAD_FUNC(value) PAD_CFG0_MODE_##value +#define PAD_RESET(value) PAD_CFG0_LOGICAL_RESET_##value +#define PAD_PULL(value) PAD_CFG1_PULL_##value + +#define PAD_IOSSTATE(value) PAD_CFG1_IOSSTATE_##value +#define PAD_IOSTERM(value) PAD_CFG1_IOSTERM_##value + +#define PAD_IRQ_CFG(route, trig, inv) \ + (PAD_CFG0_ROUTE_##route | \ + PAD_CFG0_TRIG_##trig | \ + PAD_CFG0_RX_POL_##inv) + +#if IS_ENABLED(INTEL_PINCTRL_DUAL_ROUTE_SUPPORT) +#define PAD_IRQ_CFG_DUAL_ROUTE(route1, route2, trig, inv) \ + (PAD_CFG0_ROUTE_##route1 | \ + PAD_CFG0_ROUTE_##route2 | \ + PAD_CFG0_TRIG_##trig | \ + PAD_CFG0_RX_POL_##inv) +#endif /* CONFIG_INTEL_PINCTRL_DUAL_ROUTE_SUPPORT */ + +#define _PAD_CFG_STRUCT(__pad, __config0, __config1) \ + __pad(__config0) (__config1) + +/* Native function configuration */ +#define PAD_CFG_NF(pad, pull, rst, func) \ + _PAD_CFG_STRUCT(pad, PAD_RESET(rst) | PAD_FUNC(func), PAD_PULL(pull) | \ + PAD_IOSSTATE(TX_LAST_RXE)) + +#if IS_ENABLED(CONFIG_INTEL_GPIO_PADCFG_PADTOL) +/* + * Native 1.8V tolerant pad, only applies to some pads like I2C/I2S. Not + * applicable to all SOCs. Refer EDS. + */ +#define PAD_CFG_NF_1V8(pad, pull, rst, func) \ + _PAD_CFG_STRUCT(pad, PAD_RESET(rst) | PAD_FUNC(func), PAD_PULL(pull) |\ + PAD_IOSSTATE(TX_LAST_RXE) | PAD_CFG1_TOL_1V8) +#endif + +/* Native function configuration for standby state */ +#define PAD_CFG_NF_IOSSTATE(pad, pull, rst, func, iosstate) \ + _PAD_CFG_STRUCT(pad, PAD_RESET(rst) | PAD_FUNC(func), PAD_PULL(pull) | \ + PAD_IOSSTATE(iosstate)) + +/* + * Native function configuration for standby state, also configuring iostandby + * as masked + */ +#define PAD_CFG_NF_IOSTANDBY_IGNORE(pad, pull, rst, func) \ + _PAD_CFG_STRUCT(pad, PAD_RESET(rst) | PAD_FUNC(func), PAD_PULL(pull) | \ + PAD_IOSSTATE(IGNORE)) + +/* + * Native function configuration for standby state, also configuring iosstate + * and iosterm + */ +#define PAD_CFG_NF_IOSSTATE_IOSTERM(pad, pull, rst, func, iosstate, iosterm) \ + _PAD_CFG_STRUCT(pad, PAD_RESET(rst) | PAD_FUNC(func), PAD_PULL(pull) | \ + PAD_IOSSTATE(iosstate) | PAD_IOSTERM(iosterm)) + +/* General purpose output, no pullup/down */ +#define PAD_CFG_GPO(pad, val, rst) \ + _PAD_CFG_STRUCT(pad, \ + PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_CFG0_RX_DISABLE | !!val, \ + PAD_PULL(NONE) | PAD_IOSSTATE(TX_LAST_RXE)) + +/* General purpose output, with termination specified */ +#define PAD_CFG_TERM_GPO(pad, val, pull, rst) \ + _PAD_CFG_STRUCT(pad, \ + PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_CFG0_RX_DISABLE | !!val, \ + PAD_PULL(pull) | PAD_IOSSTATE(TX_LAST_RXE)) + +/* General purpose output, no pullup/down */ +#define PAD_CFG_GPO_GPIO_DRIVER(pad, val, rst, pull) \ + _PAD_CFG_STRUCT(pad, \ + PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_CFG0_RX_DISABLE | !!val, \ + PAD_PULL(pull) | PAD_IOSSTATE(TX_LAST_RXE) | \ + PAD_CFG1_GPIO_DRIVER) + +/* General purpose output */ +#define PAD_CFG_GPO_IOSSTATE_IOSTERM(pad, val, rst, pull, iosstate, ioterm) \ + _PAD_CFG_STRUCT(pad, \ + PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_CFG0_RX_DISABLE | !!val, \ + PAD_PULL(pull) | PAD_IOSSTATE(iosstate) | PAD_IOSTERM(ioterm)) + +/* General purpose input */ +#define PAD_CFG_GPI(pad, pull, rst) \ + _PAD_CFG_STRUCT(pad, \ + PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_CFG0_TX_DISABLE, \ + PAD_PULL(pull) | PAD_IOSSTATE(TXD_RXE)) + +/* General purpose input. The following macro sets the + * Host Software Pad Ownership to GPIO Driver mode. + */ +#define PAD_CFG_GPI_GPIO_DRIVER(pad, pull, rst) \ + _PAD_CFG_STRUCT(pad, \ + PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_CFG0_TX_DISABLE, \ + PAD_PULL(pull) | PAD_CFG1_GPIO_DRIVER | PAD_IOSSTATE(TXD_RXE)) + +#define PAD_CFG_GPIO_DRIVER_HI_Z(pad, pull, rst, iosstate, iosterm) \ + _PAD_CFG_STRUCT(pad, \ + PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_CFG0_TX_DISABLE | \ + PAD_CFG0_RX_DISABLE, \ + PAD_PULL(pull) | PAD_CFG1_GPIO_DRIVER | \ + PAD_IOSSTATE(iosstate) | PAD_IOSTERM(iosterm)) + +#define PAD_CFG_GPIO_HI_Z(pad, pull, rst, iosstate, iosterm) \ + _PAD_CFG_STRUCT(pad, \ + PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_CFG0_TX_DISABLE | \ + PAD_CFG0_RX_DISABLE, PAD_PULL(pull) | \ + PAD_IOSSTATE(iosstate) | PAD_IOSTERM(iosterm)) + +/* GPIO Interrupt */ +#define PAD_CFG_GPI_INT(pad, pull, rst, trig) \ + _PAD_CFG_STRUCT(pad, \ + PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_CFG0_TX_DISABLE | \ + PAD_CFG0_TRIG_##trig | PAD_CFG0_RX_POL_NONE, \ + PAD_PULL(pull) | PAD_CFG1_GPIO_DRIVER | PAD_IOSSTATE(TXD_RXE)) + +/* + * No Connect configuration for unused pad. + * Both TX and RX are disabled. RX disabling is done to avoid unnecessary + * setting of GPI_STS. + */ +#define PAD_NC(pad, pull) \ + _PAD_CFG_STRUCT(pad, \ + PAD_FUNC(GPIO) | PAD_RESET(DEEP) | \ + PAD_CFG0_TX_DISABLE | PAD_CFG0_RX_DISABLE, \ + PAD_PULL(pull) | PAD_IOSSTATE(TXD_RXE)) + +/* General purpose input, routed to APIC */ +#define PAD_CFG_GPI_APIC(pad, pull, rst, trig, inv) \ + _PAD_CFG_STRUCT(pad, \ + PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_CFG0_TX_DISABLE | \ + PAD_IRQ_CFG(IOAPIC, trig, inv), PAD_PULL(pull) | \ + PAD_IOSSTATE(TXD_RXE)) + +/* General purpose input, routed to APIC - with IOStandby Config*/ +#define PAD_CFG_GPI_APIC_IOS(pad, pull, rst, trig, inv, iosstate, iosterm) \ + _PAD_CFG_STRUCT(pad, \ + PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_CFG0_TX_DISABLE | \ + PAD_IRQ_CFG(IOAPIC, trig, inv), PAD_PULL(pull) | \ + PAD_IOSSTATE(iosstate) | PAD_IOSTERM(iosterm)) + +/* + * The following APIC macros assume the APIC will handle the filtering + * on its own end. One just needs to pass an active high message into the + * ITSS. + */ +#define PAD_CFG_GPI_APIC_LOW(pad, pull, rst) \ + PAD_CFG_GPI_APIC(pad, pull, rst, LEVEL, INVERT) + +#define PAD_CFG_GPI_APIC_HIGH(pad, pull, rst) \ + PAD_CFG_GPI_APIC(pad, pull, rst, LEVEL, NONE) + +#define PAD_CFG_GPI_APIC_EDGE_LOW(pad, pull, rst) \ + PAD_CFG_GPI_APIC(pad, pull, rst, EDGE_SINGLE, INVERT) + +/* General purpose input, routed to SMI */ +#define PAD_CFG_GPI_SMI(pad, pull, rst, trig, inv) \ + _PAD_CFG_STRUCT(pad, \ + PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_CFG0_TX_DISABLE | \ + PAD_IRQ_CFG(SMI, trig, inv), PAD_PULL(pull) | \ + PAD_IOSSTATE(TXD_RXE)) + +/* General purpose input, routed to SMI */ +#define PAD_CFG_GPI_SMI_IOS(pad, pull, rst, trig, inv, iosstate, iosterm) \ + _PAD_CFG_STRUCT(pad, \ + PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_CFG0_TX_DISABLE | \ + PAD_IRQ_CFG(SMI, trig, inv), PAD_PULL(pull) | \ + PAD_IOSSTATE(iosstate) | PAD_IOSTERM(iosterm)) + +#define PAD_CFG_GPI_SMI_LOW(pad, pull, rst, trig) \ + PAD_CFG_GPI_SMI(pad, pull, rst, trig, INVERT) + +#define PAD_CFG_GPI_SMI_HIGH(pad, pull, rst, trig) \ + PAD_CFG_GPI_SMI(pad, pull, rst, trig, NONE) + +/* General purpose input, routed to SCI */ +#define PAD_CFG_GPI_SCI(pad, pull, rst, trig, inv) \ + _PAD_CFG_STRUCT(pad, \ + PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_CFG0_TX_DISABLE | \ + PAD_IRQ_CFG(SCI, trig, inv), PAD_PULL(pull) | \ + PAD_IOSSTATE(TXD_RXE)) + +/* General purpose input, routed to SCI */ +#define PAD_CFG_GPI_SCI_IOS(pad, pull, rst, trig, inv, iosstate, iosterm) \ + _PAD_CFG_STRUCT(pad, \ + PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_CFG0_TX_DISABLE | \ + PAD_IRQ_CFG(SCI, trig, inv), PAD_PULL(pull) | \ + PAD_IOSSTATE(iosstate) | PAD_IOSTERM(iosterm)) + +#define PAD_CFG_GPI_SCI_LOW(pad, pull, rst, trig) \ + PAD_CFG_GPI_SCI(pad, pull, rst, trig, INVERT) + +#define PAD_CFG_GPI_SCI_HIGH(pad, pull, rst, trig) \ + PAD_CFG_GPI_SCI(pad, pull, rst, trig, NONE) + +#define PAD_CFG_GPI_SCI_DEBEN(pad, pull, rst, trig, inv, dur) \ + _PAD_CFG_STRUCT_3(pad, \ + PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_CFG0_TX_DISABLE | \ + PAD_IRQ_CFG(SCI, trig, inv), PAD_PULL(pull) | \ + PAD_IOSSTATE(TXD_RXE), PAD_CFG2_DEBEN | PAD_CFG2_##dur) + +#define PAD_CFG_GPI_SCI_LOW_DEBEN(pad, pull, rst, trig, dur) \ + PAD_CFG_GPI_SCI_DEBEN(pad, pull, rst, trig, INVERT, dur) + +#define PAD_CFG_GPI_SCI_HIGH_DEBEN(pad, pull, rst, trig, dur) \ + PAD_CFG_GPI_SCI_DEBEN(pad, pull, rst, trig, NONE, dur) + +/* General purpose input, routed to NMI */ +#define PAD_CFG_GPI_NMI(pad, pull, rst, trig, inv) \ + _PAD_CFG_STRUCT(pad, \ + PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_CFG0_TX_DISABLE | \ + PAD_IRQ_CFG(NMI, trig, inv), PAD_PULL(pull) | \ + PAD_IOSSTATE(TXD_RXE)) + +#if IS_ENABLED(INTEL_PINCTRL_DUAL_ROUTE_SUPPORT) +/* GPI, GPIO Driver, SCI interrupt */ +#define PAD_CFG_GPI_GPIO_DRIVER_SCI(pad, pull, rst, trig, inv) \ + _PAD_CFG_STRUCT(pad, \ + PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_CFG0_TX_DISABLE | \ + PAD_IRQ_CFG(SCI, trig, inv), \ + PAD_PULL(pull) | PAD_CFG1_GPIO_DRIVER | PAD_IOSSTATE(TXD_RXE)) + +#define PAD_CFG_GPI_DUAL_ROUTE(pad, pull, rst, trig, inv, route1, route2) \ + _PAD_CFG_STRUCT(pad, \ + PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_CFG0_TX_DISABLE | \ + PAD_IRQ_CFG_DUAL_ROUTE(route1, route2, trig, inv), \ + PAD_PULL(pull) | PAD_IOSSTATE(TXD_RXE)) + +#define PAD_CFG_GPI_IRQ_WAKE(pad, pull, rst, trig, inv) \ + PAD_CFG_GPI_DUAL_ROUTE(pad, pull, rst, trig, inv, IOAPIC, SCI) + +#endif /* CONFIG_INTEL_PINCTRL_DUAL_ROUTE_SUPPORT */ + +#endif /* _ASM_INTEL_PINCTRL_DEFS_H_ */ |