diff options
Diffstat (limited to 'drivers')
| -rw-r--r-- | drivers/mtd/spi/Kconfig | 2 | ||||
| -rw-r--r-- | drivers/mtd/spi/sunxi_spi_spl.c | 16 | ||||
| -rw-r--r-- | drivers/net/sun8i_emac.c | 2 | ||||
| -rw-r--r-- | drivers/power/Kconfig | 4 | ||||
| -rw-r--r-- | drivers/usb/host/ehci-sunxi.c | 2 |
5 files changed, 13 insertions, 13 deletions
diff --git a/drivers/mtd/spi/Kconfig b/drivers/mtd/spi/Kconfig index 1f23c8e34e..5ca0a712d8 100644 --- a/drivers/mtd/spi/Kconfig +++ b/drivers/mtd/spi/Kconfig @@ -132,7 +132,7 @@ if SPL config SPL_SPI_SUNXI bool "Support for SPI Flash on Allwinner SoCs in SPL" - depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || MACH_SUN8I_H3 || MACH_SUN50I + depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || MACH_SUNXI_H3_H5 || MACH_SUN50I ---help--- Enable support for SPI Flash. This option allows SPL to read from sunxi SPI Flash. It uses the same method as the boot ROM, so does diff --git a/drivers/mtd/spi/sunxi_spi_spl.c b/drivers/mtd/spi/sunxi_spi_spl.c index a24c115174..852abd41de 100644 --- a/drivers/mtd/spi/sunxi_spi_spl.c +++ b/drivers/mtd/spi/sunxi_spi_spl.c @@ -185,14 +185,14 @@ static void spi0_deinit(void) #define SPI_READ_MAX_SIZE 60 /* FIFO size, minus 4 bytes of the header */ static void sunxi_spi0_read_data(u8 *buf, u32 addr, u32 bufsize, - u32 spi_ctl_reg, - u32 spi_ctl_xch_bitmask, - u32 spi_fifo_reg, - u32 spi_tx_reg, - u32 spi_rx_reg, - u32 spi_bc_reg, - u32 spi_tc_reg, - u32 spi_bcc_reg) + ulong spi_ctl_reg, + ulong spi_ctl_xch_bitmask, + ulong spi_fifo_reg, + ulong spi_tx_reg, + ulong spi_rx_reg, + ulong spi_bc_reg, + ulong spi_tc_reg, + ulong spi_bcc_reg) { writel(4 + bufsize, spi_bc_reg); /* Burst counter (total bytes) */ writel(4, spi_tc_reg); /* Transfer counter (bytes to send) */ diff --git a/drivers/net/sun8i_emac.c b/drivers/net/sun8i_emac.c index b87210bad7..abdfada646 100644 --- a/drivers/net/sun8i_emac.c +++ b/drivers/net/sun8i_emac.c @@ -62,7 +62,7 @@ #define AHB_GATE_OFFSET_EPHY 0 -#if defined(CONFIG_MACH_SUN8I_H3) +#if defined(CONFIG_MACH_SUNXI_H3_H5) #define SUN8I_GPD8_GMAC 2 #else #define SUN8I_GPD8_GMAC 4 diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig index f2c5629be2..64e5bc2f74 100644 --- a/drivers/power/Kconfig +++ b/drivers/power/Kconfig @@ -12,7 +12,7 @@ choice default AXP209_POWER if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I default AXP221_POWER if MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 default AXP818_POWER if MACH_SUN8I_A83T - default SUNXI_NO_PMIC if MACH_SUN8I_H3 || MACH_SUN50I + default SUNXI_NO_PMIC if MACH_SUNXI_H3_H5 || MACH_SUN50I config SUNXI_NO_PMIC bool "board without a pmic" @@ -60,7 +60,7 @@ config AXP818_POWER config SY8106A_POWER bool "SY8106A pmic support" - depends on MACH_SUN8I_H3 + depends on MACH_SUNXI_H3_H5 ---help--- Select this to enable support for the SY8106A pmic found on some H3 boards. diff --git a/drivers/usb/host/ehci-sunxi.c b/drivers/usb/host/ehci-sunxi.c index 5bb97ff45b..068f24f483 100644 --- a/drivers/usb/host/ehci-sunxi.c +++ b/drivers/usb/host/ehci-sunxi.c @@ -45,7 +45,7 @@ static int ehci_usb_probe(struct udevice *dev) * clocks resp. phys. */ priv->ahb_gate_mask = 1 << AHB_GATE_OFFSET_USB_EHCI0; -#if defined(CONFIG_MACH_SUN8I_H3) || defined(CONFIG_MACH_SUN50I) +#if defined(CONFIG_MACH_SUNXI_H3_H5) || defined(CONFIG_MACH_SUN50I) extra_ahb_gate_mask = 1 << AHB_GATE_OFFSET_USB_OHCI0; #endif priv->phy_index = ((uintptr_t)hccr - SUNXI_USB1_BASE) / BASE_DIST; |