summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-05-08Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini
- H6 Beelink GS1 board (Clément) - Olimex A64-Teres-I board (Jonas) - sunxi build fix for CONFIG_CMD_PXE|DHCP (Ondrej) - Change include order (Jagan) - EPHY clock changes (Jagan) - EMAC enablement on Cubietruck Plus, BPI-M3 (Chen-Yu Tsai)
2019-05-09sunxi: Enable EMAC on the Bananapi M3Chen-Yu Tsai
The Bananapi M3 has an RTL8211E PHY connected to the EMAC using RGMII. The PHY is powered by DCDC1 through SW @ 3.3V. The board is designed to use 3.3V with RGMII, instead of the standard reduced voltage of 2.5V we see everywhere. DLDO3, which provides the I/O voltages, is raised to match. This patch enables the EMAC and Realtek PHY drivers in the defconfig. The device tree file already has the EMAC enabled. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-05-09sunxi: Enable EMAC on the Cubietruck PlusChen-Yu Tsai
The Cubietruck Plus has an RTL8211E PHY connected to the EMAC using RGMII. The PHY is powered by DLDO4 @ 3.3V, while the I/O pins are powered by DLDO3 @ 2.5V. This patch enables the EMAC and Realtek PHY drivers in the defconfig. The device tree file already has the EMAC enabled. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-05-09sun50i: a64: Add Olimex A64-Teres-I board initial supportJonas Smedegaard
Olimex A64-Teres-I board is a mainboard (the only one so far) for Olimex Teres-I DIY laptop kit. Key features: - Allwinner A64 Cortex-A53 - Mali-400MP2 GPU - AXP803 PMIC - 2GB DDR3 RAM - MicroSD Slot - 16GB eMMC Flash - eDP LCD display - HDMI - USB Host - Battery management - 5V DC power supply - Certified Open Source Hardware (OSHW) Works: - i2C - MMC/SD - PWM backlight Known broken: - Internal keyboard (seems to be because the keyboard firmware loads a bootloader first, and then disconnects bootloader and connect real keyboard). External ones connected to the USB port work fine. This patch enables support for the A64-Teres-I board to u-boot, including enabling screen backlight (lacking from Linux device-tree). Linux commit details about the sun50i-a64-teres-i.dts sync: "arm64: dts: allwinner: a64: Rename uart0_pins_a label to uart0_pb_pins" (sha1: d91ebb95b96c8840932dc3a10c9f243712555467) Cosmetic warnings regarding whitespace and placement of SPDX notice for dts file was ignored. config and .dtsi file are adapted from pinebook files. Tested-by: Jonas Smedegaard <dr@jones.dk> Signed-off-by: Jonas Smedegaard <dr@jones.dk> Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> [jagan: move board entry in MAINTAINERS file at proper position] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-05-09net: sun8i_emac: Add EPHY CLK and RESET supportJagan Teki
Add EPHY CLK and RESET support for sun8i_emac driver to enable EPHY TX clock and EPHY reset pins via CLK and RESET framework. Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Lothar Felten <lothar.felten@gmail.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-05-09test/dm: reset: Add reset_get_by_index[_nodev] testJagan Teki
Add sample dm reset test for reset_get_by_index and reset_get_by_index_nodev functionality code. Cc: Stephen Warren <swarren@nvidia.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-05-09reset: Get the RESET by index without deviceJagan Teki
Getting a RESET by index with device is not straight forward for some use-cases like handling clock operations for child node in parent driver. So we need to process the child node in parent probe via ofnode and process RESET operation for child without udevice but with ofnode. So add reset_get_by_index_nodev() and move the common code in reset_get_by_index_tail() to use for reset_get_by_index() Cc: Stephen Warren <swarren@nvidia.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-05-09test/dm: clk: Add clk_get_by_index[_nodev] testJagan Teki
Add sample dm clk test for clk_get_by_index and clk_get_by_index_nodev functionality code. Cc: Stephen Warren <swarren@nvidia.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-05-09clk: Use clk_get_by_index_tail()Jagan Teki
clk_get_by_index_tail() now handle common clk get by index code so use it from clk_get_by_indexed_prop(). Cc: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-05-09clk: Get the CLK by index without deviceJagan Teki
Getting a CLK by index with device is not straight forward for some use-cases like handling clock operations for child node in parent driver. So we need to process the child node in parent probe via ofnode and process CLK operation for child without udevice but with ofnode. So add clk_get_by_index_nodev() and move the common code in clk_get_by_index_tail() to use for clk_get_by_index() Cc: Stephen Warren <swarren@nvidia.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-05-09serial: sifive: Change include orderJagan Teki
Like clk_get_by_index, there is requirement for clk_get_by_index_nodev. In this case to make common code functionalities for dev and nodev, clk_get_by_index is trying to get the index of clock by passing ofnode instead of actual dev like current gpio uclass does. In these scenarios with current order of include files the serial_sifive driver is unable to find CONFIG_ENV_SIZE. In file included from arch/riscv/include/asm/u-boot.h:23:0, from include/dm/of.h:10, from include/dm/ofnode.h:12, from include/clk.h:11, from drivers/serial/serial_sifive.c:6: include/environment.h:145:19: error: 'CONFIG_ENV_SIZE' undeclared here (not in a function); did you mean 'CONFIG_CMD_XIMG'? #define ENV_SIZE (CONFIG_ENV_SIZE - ENV_HEADER_SIZE) So, fix consists of changing the order of include files in serial_sifive.c to include first common.h file. Cc: Anup Patel <Anup.Patel@wdc.com> Cc: Rick Chen <rick@andestech.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-05-09clk: sifive: fu540-prci: Change include orderJagan Teki
Like clk_get_by_index, there is requirement for clk_get_by_index_nodev. In this case to make common code functionalities for dev and nodev, clk_get_by_index is trying to get the index of clock by passing ofnode instead of actual dev like current gpio uclass does. In these scenarios with current order of include files the fu540-prci driver is unable to find CONFIG_ENV_SIZE. In file included from arch/riscv/include/asm/u-boot.h:23:0, from include/dm/of.h:10, from include/dm/ofnode.h:12, from include/clk.h:11, from include/clk-uclass.h:13, from drivers/clk/sifive/fu540-prci.c:32: include/environment.h:145:19: error: 'CONFIG_ENV_SIZE' undeclared here (not in a function); did you mean 'CONFIG_CMD_XIMG'? #define ENV_SIZE (CONFIG_ENV_SIZE - ENV_HEADER_SIZE) So, fix consists of changing the order of include files in fu540-prci.c to include first common.h file. Cc: Anup Patel <Anup.Patel@wdc.com> Cc: Rick Chen <rick@andestech.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-05-09spi: atcspi200: Change include orderJagan Teki
Like clk_get_by_index, there is requirement for clk_get_by_index_nodev. In this case to make common code functionalities for dev and nodev, clk_get_by_index is trying to get the index of clock by passing ofnode instead of actual dev like current gpio uclass does. In these scenarios with current order of include files the atcspi200_spi driver is unable to find CONFIG_ENV_SIZE. In file included from arch/nds32/include/asm/u-boot.h:24, from include/dm/of.h:10, from include/dm/ofnode.h:12, from include/clk.h:11, from drivers/spi/atcspi200_spi.c:9: include/environment.h:145:19: error: 'CONFIG_ENV_SIZE' undeclared here (not in a function); did you mean 'CONFIG_CMD_XIMG'? #define ENV_SIZE (CONFIG_ENV_SIZE - ENV_HEADER_SIZE) So, fix consists of changing the order of include files in atcspi200_spi.c to include first common.h file. Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-05-08Merge git://git.denx.de/u-boot-x86Tom Rini
- Allow x86 boards to use TPL, SPL and U-Boot proper - Update sysreset x86 driver to utilize ACPI registers to do power off - Add a new chromebook_samus_tpl board for TPL support - Several minor changes in binman tool
2019-05-08Merge tag 'efi-2019-07-rc2-2' of git://git.denx.de/u-boot-efiTom Rini
Pull request for UEFI sub-system for v2019.07-rc2 (2) Fix a bunch of errors in the UEFI sub-system: * implement missing UnloadImage(), * implement missing RegisterProtocolNotify(), * unload images in Exit(), * parameter checks. Provide a unit test for UnloadImage(). Remove a redundant function for unit tests. Clean up the UEFI sub-system initialization
2019-05-08rockchip: dts: rk3399: Sync rk3399-nanopi4.dtsi from LinuxJagan Teki
Sync rk3399-nanopi4.dtsi from Linux 5.1-rc2 tag. Linux commit details about the rk3399-nanopi4.dtsi sync: "arm64: dts: rockchip: Add nanopi4 bluetooth" (sha1: 3e2f0bb72be36aa6c14ee7f11ac4dd8014801030) Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08arm: rockchip: rk3399: Move common configs in KconfigJagan Teki
Few SPL and U-Boot proper configs are common to all rk3399 target defconfigs, move them and select it from platform kconfig. Moved configs: - SPL_ATF - SPL_ATF_NO_PLATFORM_PARAM if SPL_ATF - SPL_LOAD_FIT - SPL_CLK if SPL - SPL_PINCTRL if SPL - SPL_RAM if SPL - SPL_REGMAP if SPL - SPL_SYSCON if SPL - CLK - FIT - PINCTRL - RAM - REGMAP - SYSCON - DM_PMIC - DM_REGULATOR_FIXED Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08Kconfig: Add default SPL_FIT_GENERATOR for rockchipJagan Teki
Add default SPL_FIT_GENERATOR py script for rockchip platforms if specific target enabled SPL_LOAD_FIT. So, this would help get rid of explicitly mentioning the default SPL FIT generator in defconfigs. however some targets, like puma_rk3399 still require their own FIT generator so in those cases the default will override with defconfig defined generator. Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08rockchip: dts: rk3399: Sync pwm2_pin_pull_down from Linux 5.1-rc2Jagan Teki
To make successful build with dts(i) files syncing from Linux 5.1-rc2 the rk3399.dtsi would require pwm2_pin_pull_down. So, sync the pwm2_pin_pull_down node from Linux 5.1-rc2. Since this node is strictly not part of any commit alone, I have mentioned Linux 5.1-rc2 tag for future reference of where would this sync coming from. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08rockchip: rk3399: orangepi: Add SPL_TEXT_BASEJagan Teki
CONFIG_SPL_TEXT_BASE was available in configs/rk3399_common.h when the OrangePI rk3399 board supported during first version patch. But, later below change which move this config into Kconfig and same has been merged in mainline tree. "configs: move CONFIG_SPL_TEXT_BASE to Kconfig" (sha1: f89d6133eef2e068f9c33853b6584d7fcbfa9d2e) Unfortunately, the maintainer applied the initial version patch, instead of looking for next version changes. Fix it by adding SPL_TEXT_BASE in orangepi-rk3399 defconfig. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08arm64: rockchip: dts: rk3399: Use rk3399-u-boot.dtsiJagan Teki
Now we have - board specific -u-boot.dtsi files for board specific u-boot dts changes. - soc specific rk3399-u-boot.dtsi for soc specific u-boot dts changes. So, include the rk3399-u-boot-dtsi on respective board -u-boot.dtsi and drop the properties which are globally available in rk3399-u-boot.dtsi Right now rk3399-u-boot.dtsi has sdmmc, spi1 u-boot,dm-pre-reloc property and more properties and nodes can be move further based on the requirements. This would fix, the -u-boot.dtsi inclusion for evb, firefly, puma boards that was accidentally merged on below commit. "rockchip: dts: rk3399: Create initial rk3399-u-boot.dtsi" (sha1: e05b4a4fa84b65a0c8873e8f34721741fe2bc09d) Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08rockchip: dts: rk3399-u-boot: Add u-boot, dm-pre-reloc for spi1Jagan Teki
Add u-boot,dm-pre-reloc property for spi1, so-that the subsequent rk3399 boards which boot from SPI. This help to separate the u-boot specific properties away from base dts files so-that the Linux sync become easy and meaningful. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08arm64: rockchip: dts: rk3399: Add board -u-boot.dtsi filesJagan Teki
Devicetree files in RK3399 platform is synced from Linux, like other platforms does. Apart from these u-boot in rk3399 would also require some u-boot specific node like dmc. dmc node has big chunk of DDR timing parameters which are specific to specific board, and maintained with rk3399-sdram*.dtsi. So, create board specific -u-boot.dtsi files and move these sdram dtsi files accordingly. This would help of maintain u-boot specific changes separately without touching Linux dts(i) files which indeed easy for syncing from Linux between releases. These board specific -u-boot.dtsi can be extendible to add more u-boot specific nodes or properties in future. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08dts: Makefile: Build rockchip dtbs based on SoC typesJagan Teki
- Sometimes u-boot specific dtsi files are included automatically which would build for entire rockchip SoC, even-though the respective dtsi should used it for specific family of rockchip SoC. - Sometimes u-boot specific dts nodes or properties can use config macros from respective rockchip family include/configs files, example CONFIG_SPL_PAD_TO. So, it's better to compile the dtbs based on the respective rockchip family types rather than rockchip itself to avoid compilation issues. This patch organize the existing dtb's based on the rockchip family types. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08pinctrl: rockchip: Also move common set_schmitter func into per Soc fileDavid Wu
Only some Soc need Schmitter feature, so move the implementation into their own files. Signed-off-by: David Wu <david.wu@rock-chips.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08pinctrl: rockchip: Clean the unused type and labelDavid Wu
As the mux/pull/drive feature implement at own file, the type and label are not necessary. Signed-off-by: David Wu <david.wu@rock-chips.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08pinctrl: rockchip: Special treatment for RK3288 gpio0 pins' pullDavid Wu
RK3288 pmu_gpio0 pull setting have no higher 16 writing corresponding bits, need to read before write the register. Signed-off-by: David Wu <david.wu@rock-chips.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08pinctrl: rockchip: Split the common set_pull() func into per SocDavid Wu
As the common set_mux func(), implement the feature at the own file for each Soc. Signed-off-by: David Wu <david.wu@rock-chips.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08pinctrl: rockchip: Special treatment for RK3288 gpio0 pins' drive strengthDavid Wu
RK3288 pmu_gpio0 drive strength setting have no higher 16 writing corresponding bits, need to read before write the register. Signed-off-by: David Wu <david.wu@rock-chips.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08pinctrl: rockchip: Split the common set_drive() func into per SocDavid Wu
As the common set_mux func(), implement the feature at the own file for each Soc. Signed-off-by: David Wu <david.wu@rock-chips.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08pinctrl: rockchip: Special treatment for RK3288 gpio0 pins' iomuxDavid Wu
RK3288 pmu_gpio0 iomux setting have no higher 16 writing corresponding bits, need to read before write the register. Signed-off-by: David Wu <david.wu@rock-chips.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08pinctrl: rockchip: Split the common set_mux() into per SocDavid Wu
Such as rk3288's pins of pmu_gpio0 are a special feature, which have no higher 16 writing corresponding bits, use common set_mux() func would introduce more code, so implement their set_mux() in each Soc's own file to reduce the size of code. Signed-off-by: David Wu <david.wu@rock-chips.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08pinctrl: rockchip: Remove redundant spacesDavid Wu
Some files have the redundant spaces, remove them. Signed-off-by: David Wu <david.wu@rock-chips.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08pinctrl: rockchip: Add pull-pin-default param and remove unused paramDavid Wu
Some Socs use the pull-pin-default config param, need to add it. And input-enable/disable config params are not necessary, remove it. Signed-off-by: David Wu <david.wu@rock-chips.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08Revert "pinctrl: rockchip: Add 32bit writing function for rk3288 gpio0 pinctrl"Kever Yang
This reverts commit 502980914b2d6f9ee85a823aa3ef9ead76c0b7f2. This is a superseded version, revert this to apply new patch set. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08rockchip: chromebook_minnie: Enable soundSimon Glass
Enable sound for this board, which has the same codec as jerry. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08rockchip: rk3399: update defconfig for TPLKever Yang
The SPL is now running at SDRAM, and 0x10000 is used by BL31, and the ARM SPL do not support relocate now, we need reserved 0x50000 so that it won't overwrite the code when we load the bl31 to target space. We should remove this after we enable the relocate feature. The SPL need malloc 0x9000 for MMC as buffer used for transfer data to IRAM(The EMMC DMA can not transfer data to IRAM directly). Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08rockchip: ram: rk3399: update for TPLKever Yang
Init the ddr sdram in TPL instead of SPL, update the code. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Tested-by: Andy Yan <andy.yan@rock-chips.com>
2019-05-08rockchip: rk3399: add tpl supportKever Yang
Rockchip platform suppose to use TPL(run in SRAM) as dram init and SPL(run in DDR SDRAM) as pre-loader, so that the SPL would not be limited by SRAM size. This patch add rk3399-board-tpl.c and its common configs. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08rockchip: add u-boot-tpl-v8.ldsKever Yang
We don't have both sram and sdram in TPL, so update from: arch/arm/cpu/armv8/u-boot-spl.lds Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-05-08rockchip: px5: add timer0 dts node as tick timerKever Yang
Let's use rockchip timer before stimer patches can be merged. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08rockchip: rk3368: remove uart iomux init in SPLKever Yang
The iomux should have been set in board_debug_uart_init(), do not set in board_init_f(), remove it. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08rockchip: dmc: rk3368: update rank number for evb-px5Kever Yang
evb-px5 has only 1 CS, update for it. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Tested-by: Andy Yan <andy.yan@rock-chips.com>
2019-05-08rockchip: boot0: update CONFIG_ROCKCHIP_SPL_RESERVE_IRAM for SPL onlyKever Yang
The CONFIG_ROCKCHIP_SPL_RESERVE_IRAM is for SPL only, add condition to limit it not affect TPL. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08rockchip: px5: update defconfig for TPL/SPLKever Yang
Add options to support TPL. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08rockchip: px5: update SPL size for spl/tplKever Yang
Use larger space for load bl31 in SPL Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Tested-by: Andy Yan <andy.yan@rock-chips.com>
2019-05-08rockchip: px5 update dts for spl/tplKever Yang
TPL need dmc to init ddr sdram, and emmc, boot-order. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Tested-by: Andy Yan <andy.yan@rock-chips.com>
2019-05-08rockchip: rk3368: support UART2/4 in board_debug_uart_init()Kever Yang
evb-rk3368 is using UART2 and PX5 evb is using UART4 Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Tested-by: Andy Yan <andy.yan@rock-chips.com>
2019-05-08rockchip: evb-rk322x: update defconfig with tpl and optee supportKever Yang
Enable all the options for TPL/SPL and OPTEE. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08rockchip: evb-rk3229: add README file for OP-TEE supportKever Yang
Detail of step by step to bring up the board with OP-TEE support. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
generated by cgit (git 2.34.1) at 2025-01-01 20:40:17 +0000