summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2016-05-26ARM: uniphier: disable cache in SPL of PH1-LD20Masahiro Yamada
The Boot ROM has enabled D-cache and MMU setting DDR memory area as Normal Memory in its page table. Disable D-cache and MMU before jumping to U-Boot proper. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-05-25Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini
2016-05-24powerpc:t4240: MAC9 and MAC10 should not be identified as 1G interface in ↵Ying Zhang
some case When using rcw protocols to support 10G on MAC9 and MAC10, these MACs should not be identified as 1G interface, otherwise, one MAC will be listed as two Ethernet ports. For example, MAC9 will be listed as FM1@TGEC1 and FM1@DTSEC9. Signed-off-by: Ying Zhang <b40530@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-24powerpc:t4240rdb: Disable the non-existent ethernet ports on T4240RDBYing Zhang
Disable the non-existent ethernet ports on T4240RDB:FM1_DTSEC5, FM1_DTSEC6, FM2_DTSEC5 and FM2_DTSEC6. Signed-off-by: Ying Zhang <ying.zhang22455@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-24Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini
2016-05-24powerpc/mpc85xx: set L2PE in L2CSR0 before enabling L2 cacheAneesh Bansal
While enabling L2 cache, the value of L2PE (L2 cache parity/ECC error checking enable) must not be changed while the L2 cache is enabled. So, L2PE must be set before enabling L2 cache. Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-24Merge branch 'master' of git://git.denx.de/u-boot-netTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: drivers/net/zynq_gem.c
2016-05-24net: phy: dp83867: Add SGMII helper for configurationDan Murphy
The code assumed that if the interface is not RGMII configured then it must be SGMII configured. This device has the ability to support most of the MII interfaces. Therefore add the helper for SGMII and only configure the device if the interface is configured for SGMII. Signed-off-by: Dan Murphy <dmurphy@ti.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24net: phy: Add phy_interface_is_sgmii to phy.hDan Murphy
Add a helper to phy.h to identify whether the phy is configured for SGMII all variables. Signed-off-by: Dan Murphy <dmurphy@ti.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24net: phy: Move is_rgmii helper to phy.hDan Murphy
Move the phy_interface_is_rgmii to the phy.h file for all phy's to be able to use the API. This now aligns with the Linux kernel based on commit e463d88c36d42211aa72ed76d32fb8bf37820ef1 Signed-off-by: Dan Murphy <dmurphy@ti.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24net: phy: ti: Allow the driver to be more configurableDan Murphy
Not all devices use the same internal delay or fifo depth. Add the ability to set the internal delay for rx or tx and the fifo depth via the devicetree. If the value is not set in the devicetree then set the delay to the default. If devicetree is not used then use the default defines within the driver. Signed-off-by: Dan Murphy <dmurphy@ti.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24net: phy: dp83867: Add device tree bindings and documentationDan Murphy
Add the device tree bindings and the accompanying documentation for the TI DP83867 Giga bit ethernet phy driver. The original document was from: [commit 2a10154abcb75ad0d7b6bfea6210ac743ec60897 from the Linux kernel] Signed-off-by: Dan Murphy <dmurphy@ti.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24net: zynq_gem: Add the passing of the phy-handle nodeDan Murphy
Add the ability to pass the phy-handle node offset to the phy driver. This allows the phy driver to access the DT subnode's data and parse accordingly. Signed-off-by: Dan Murphy <dmurphy@ti.com> Tested-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24drivers: net: cpsw: Add reading of DT phy-handle nodeDan Murphy
Add the ability to read the phy-handle node of the cpsw slave. Upon reading this handle the phy-id can be stored based on the reg node in the DT. The phy-handle also needs to be stored and passed to the phy to access any phy data that is available. Signed-off-by: Dan Murphy <dmurphy@ti.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24defconfig: dra74_evm: enable eth driver modelMugunthan V N
Enable eth driver model for dra74_evm as cpsw supports driver model. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24defconfig: am437x_sk_evm: enable eth driver modelMugunthan V N
Enable eth driver model for am437x_sk_evm as cpsw supports driver model. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24defconfig: am437x_gp_evm: enable eth driver modelMugunthan V N
Enable eth driver model for am437x_gp_evm as cpsw supports driver model. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24arm: dts: dra7: fix ethernet name with proper device addressMugunthan V N
Fix typo error for cpsw device name with proper device address Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24arm: dts: dra7: add syscon node to cpsw to read mac addressMugunthan V N
Add syscon node to cpsw device node to read mac address from efuse. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24arm: dts: am4372: add syscon node to cpsw to read mac addressMugunthan V N
Add syscon node to cpsw device node to read mac address from efuse. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24drivers: net: cpsw: add support for reading mac address from efuseMugunthan V N
Different TI platforms has to read with different combination to get the mac address from efuse. So add support to read mac address based on machine/device compatibles. The code is taken from Linux drivers/net/ethernet/ti/cpsw-common.c done by Tony Lindgren. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24drivers: net: cpsw: fix get mdio base and gmii_sel reg from DTMugunthan V N
Since dra7x platforms address bus is define as 64 bits to support LAPE, fdtdec_get_addr() returns a invalid address for mdio based and gmii_sel register address. Fixing this by using fdtdec_get_addr_size_auto_noparent() which will derive address cell and size cell from its parent. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24ARM: omap5: add platform specific ethernet phy modes configurationsMugunthan V N
Add platforms specific phy mode configuration bits to be used to configure phy mode in control module. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24drivers: net: cpsw: fix cpsw dp parse when num slaves as 1Mugunthan V N
On some boards number of slaves can be 1 when only one port ethernet is pinned out. So do not break when slave_index and num slaves check fails, instead continue to parse the next child. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24ti_omap5_common: eth: do not define DM_ETH for splMugunthan V N
Since omap's spl doesn't support DM currently, do not define DM_ETH for spl build. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24drivers: core: device: add support to check dt compatible for a device/machineMugunthan V N
Provide an api to check whether the given device or machine is compatible with the given compat string which helps in making decisions in drivers based on device or machine compatible. Idea taken from Linux. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24net: phy: Add PHY driver for mv88e61xx switchesKevin Smith
The previous mv88e61xx driver was a driver for configuring the switch, but did not integrate with the PHY/networking system, so it could not be used as a PHY by U-boot. This is a complete rework to support this device as a PHY. Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com> Acked-by: Prafulla Wadaskar <prafulla@marvell.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Stefan Roese <sr@denx.de> Cc: Marek Vasut <marex@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24net: Remove unused mv88e61xx switch driverKevin Smith
No boards are using this driver. Remove in preparation for a new driver with integrated PHY support. Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Stefan Roese <sr@denx.de> Cc: Marek Vasut <marex@denx.de>
2016-05-24Merge branch 'master' of git://www.denx.de/git/u-boot-microblazeTom Rini
2016-05-24Merge branch 'master' of git://git.denx.de/u-boot-atmelTom Rini
2016-05-24ARM: zynq: Simplify zynq configurationMichal Simek
Extending Kconfig for adding new platform is a lot of work for nothing. Setting SYS_CONFIG_NAME directly in Kconfig and remove all dependencies on TARGET_ZYNQ_* options including SPL. As a side-effect it also remove custom init folder for ps7_init_gpl.* files. Folder is chosen based on device-tree file. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24phy: marvell: Do not reset phy after negotiationMichal Simek
The patch "net: phy: do not read configuration register on reset" (sha1: a058052c358c3ecf5f394ff37def6a45eb26768c) was causing regression on zynq zc702 board where Marwell 88e1118 phy was resetted after negotiation was setup. Phy reset is done pretty early in phy_connect_dev() and doens't need to be called again in phy code. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24phy: Wire return value from phy_config()Michal Simek
Fix zynq_gem driver to handle error from phy_config correctly. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24image: Add boot_get_fpga() to load fpga with bootmMichal Simek
Add function boot_get_fpga() which find and load bitstream to programmable logic if fpga entry is present. Function is supported on Xilinx devices for full and partial bitstreams in BIN and BIT format. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Remove additional blankline in image.h
2016-05-24net: phy: Handle phy_startup() error codes properlyMichal Simek
Propagate error code from genphy_update_link() to phy startup(). Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Stephen Warren <swarren@nvidia.com>
2016-05-24phy: Return correct error code when timeout happensMichal Simek
Return -ETIMEDOUT if timeout happens. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Stephen Warren <swarren@nvidia.com>
2016-05-24net: xilinx: Handle error value from phy_startup()Michal Simek
Handle error returned by phy_startup() properly. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Stephen Warren <swarren@nvidia.com>
2016-05-24mkimage: Report information about fpgaMichal Simek
Add FIT_FPGA_PROP that user can identify an optional entry for fpga. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-24fpga: Fix typo in function commentMichal Simek
Trivial patch. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24ARM64: zynqmp: Enable CLK frameworkMichal Simek
ZynqMP is using fixed clocks now that's why enabling it to be available for drivers. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24ARM64: zynqmp: Add SPL support supportMichal Simek
Support RAM and MMC boot mode in SPL also with SPL_FIT images. In MMC boot mode two boot options are available: 1) Boot flow with ATF(EL3) and full U-Boot(EL2): aarch64-linux-gnu-objcopy -O binary bl31.elf bl31.bin mkimage -A arm64 -O linux -T kernel -C none -a 0xfffe5000 -e 0xfffe5000 -d bl31.bin atf.ub cp spl/boot.bin <sdcard fat partition> cp atf.ub <sdcard fat partition> cp u-boot.bin <sdcard fat partition> 2) Boot flow with full U-Boot(EL3): cp spl/boot.bin <sdcard> cp u-boot*.img <sdcard> 3) emmc boot mode dd if=/dev/zero of=sd.img bs=1024 count=1024 parted sd.img mktable msdos parted sd.img mkpart p fat32 0% 100% kpartx -a sd.img mkfs.vfat /dev/mapper/loop0p1 mount /dev/mapper/loop0p1 /mnt/ cp spl/boot.bin /mnt cp u-boot.img /mnt cp u-boot.bin /mnt cp atf.ub /mnt umount /dev/mapper/loop0p1 kpartx -d sd.img cp sd.img /tftpboot/ and program it via u-boot tftpb 10000 sd.img mmcinfo mmc write 10000 0 $filesize mmc rescan mmc part ls mmc 0 psu_init() function contains low level SoC setup generated for every HW design by Xilinx design tools. xil_io.h is only supporting file to fix all dependencies from tools. The same solution was used on Xilinx Zynq. The patch also change CONFIG_SYS_INIT_SP_ADDR to the end of OCM which stays at the same location all the time. Bootrom expects starting address to be at 0xfffc0000 that's why this address is SPL_TEXT_BASE. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24ARM64: zynqmp: Add missing u-boot,dm-pre-reloc to DTSIMichal Simek
Add missing u-boot,dm-pre-reloc to get IPs initialized. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24ARM64: zynqmp: Align gic ranges for 64k in device treeAlexander Graf
The GIC ranges in the zynqmp device tree are only 4kb aligned. Since commit 12e14066f we automatically deal with aliases GIC regions though, so we can map them transparently into guests even on 64kb page size systems. This patch makes use of that features and sets GICC and GICV to 64kb aligned and sized regions. Signed-off-by: Alexander Graf <agraf@suse.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24tools: zynqmpimage: Add Xilinx ZynqMP boot header generationMichal Simek
Add support for the zynqmpimage to mkimage. Only basic functionality is supported without encryption and register initialization with one partition which is filled by U-Boot SPL. For more detail information look at Xilinx ZynqMP TRM. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-24SPL: FIT: Enable SPL_FIT_LOAD in RAM based boot modeMichal Simek
Support loading FIT in SPL for RAM bootmode. CONFIG_SPL_LOAD_FIT_ADRESS points to address where FIT image is stored in memory. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-24ARM: zynq: Call ps7_post_config() for SPLMichal Simek
If ps7_post_config() is defined call it. It is enabling for example level shifters for PL bitstreams. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24ARM64: zynqmp: Enable option to overwrite default variablesMichal Simek
Enable overwriting variables out of main config file. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24spl: Introduce new function spl_board_prepare_for_bootMichal Simek
Call this function before passing control from SPL. For fpga case it is necessary to enable for example level shifters when bitstream is programmed. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-24ARM64: zynqmp: Add debug uart for zc1751-dc1Michal Simek
It is helpful for debugging. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24ARM64: zynqmp: Enable SPI_FLASH and FLASH_BAR for ep108Michal Simek
Add missing SPI flash options. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
generated by cgit (git 2.34.1) at 2024-12-24 19:42:47 +0000