| Age | Commit message (Collapse) | Author |
|---|
|
Now that we have converted all x86 boards to use driver model pci,
remove these legacy pci codes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
These are leftover when converted to use driver model pci.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Move to driver model for ETH (e1000) on QEMU.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Move to driver model for USB on QEMU.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Move to driver model for pci on QEMU.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Move chipset-specific codes such as PAM init, PCIe ECAM and MP table
from pci.c to qemu.c, to prepare for DM PCI conversion.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
The call to pci_run_vga_bios() is not needed as this is handled
in the vesa_fb driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Currently timer_init() is called in board_r.c which is quite late.
Some vgabios execution requires we set up the i8254 timer correctly,
but video initialization comes before timer_init(). Move the call
to board_f.c.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
According to Atom E6xx datasheet, setting VGA Disable (bit17)
of Graphics Controller register (offset 0x50) prevents IGD
(D2:F0) from reporting itself as a VGA display controller
class in the PCI configuration space, and should also prevent
it from responding to VGA legacy memory range and I/O addresses.
However test result shows that with just VGA Disable bit set and
a PCIe graphics card connected to one of the PCIe controllers on
the E6xx, accessing the VGA legacy space still causes system hang.
After a number of attempts, it turns out besides VGA Disable bit,
the SDVO (D3:F0) device should be disabled to make it work.
To simplify, use the Function Disable register (offset 0xc4)
to disable both IGD (D2:F0) and SDVO (D3:F0) devices. Now these
two devices will be completely disabled (invisible in the PCI
configuration space) unless a system reset is performed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Add Kconfig options for 8259 and 8254.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Rename pcat_timer.c to i8254.c and pcat_interrupts.c to i8259.c,
to match their header file names (i8254.h and i8259.h).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Initialize counter 1, used to refresh request signal. This is
required for legacy purpose as some codes like vgabios utilizes
counter 1 to provide delay functionality.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
This cleans up i8254 and i8259 codes to fix several cosmetic
issues, like coding convention and some comments improvement.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
PARANOID_IRQ_TRIGGERS is not referenced anywhere in U-Boot.
Remove these dead codes wrapped by it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
CONFIG_SYS_NUM_IRQS is actually not something we can configure,
but an architecture defined number of ISA IRQs. Move it from
x86-common.h to asm/interrupt.h and rename it to SYS_NUM_IRQS.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Prior to commit 5ba534d247d418 ("arm: Switch 32-bit ARM to using generic
global_data setup") we used to have assembly code that configured the
malloc_base address.
Since this commit we use the board_init_f_mem() function in C to setup
malloc_base address.
In board_init_f_mem() there was a deliberate choice to support only
early malloc() or full malloc() in SPL, but not both.
Adapt this logic to allow both to be used, one after the other, in SPL.
This issue has been observed in a Congatec board, where we need to
retrieve the manufacturing information from the SPI NOR (the SPI API
calls malloc) prior to configuring the DRAM. In this case as malloc_base
was not configured we always see malloc to fail.
With this change we are able to use malloc in SPL prior to DRAM gets
initialized.
Also update the CONFIG_SYS_SPL_MALLOC_START entry in the README file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
|
|
This adds support to update firmware on qspi flash present on
am437x-sk-evm and am43xx-epos-evm via DFU.
On device:
=> setenv dfu_alt_info ${dfu_alt_info_qspi}
=> dfu 0 sf 0:0
On host:
$ sudo dfu-util -l
$ sudo dfu-util -D u-boot.bin -a u-boot.bin
Signed-off-by: Vignesh R <vigneshr@ti.com>
|
|
CONFIG_OF_EMBED=y is the option which is here only for testing purpose
and shouldn't be enabled by default as is describe at:
"dts: Add a comment about CONFIG_OF_EMBED being for local use"
(sha1: 3d3f60cb7a6bb6c338e00a9769fa918a8536096c)
But still enabling this option locally shouldn't end up with compilation
error when you build SPL. This patch fix it.
Compilation error:
lib/built-in.o: In function `fdtdec_setup':
/mnt/disk/u-boot/lib/fdtdec.c:1246: undefined reference to
`__dtb_dt_begin'
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reported-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Dear u-boot community,
I just made a small change on the openrisc-generic platform
configuration to take in account the new naming convention (or1k instead
of or32, so the build process gets fine).
Could you take care to review and approve the following patch, please?
Kind regards,
|
|
Looks like one spot got missed. Probably due to the backslash.
Signed-off-by: Andy Fleming <afleming@gmail.com>
|
|
-> Add National instrument ethernet transceiver configuration used (DP83848)
-> Change cpsw slave phy address
-> modify nand configuration to use the correct ECC and correct nand features
|
|
CONFIG_AHCI_SETFEATURES_XFER is not selected by any user, so delete
the dead code.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
get_clocks is wrapped by CONFIG_FSL_CLK and CONFIG_M68K in seperate
piece code. They can be merged into one snippet.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: "angelo@sysam.it" <angelo@sysam.it>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: "Andreas Bießmann" <andreas.devel@googlemail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Angelo Dureghello <angelo@sysam.it>
|
|
CONFIG_BOOTDELAY is defined in config_distro_defaults.h
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
[trini: Drop omap3_logic.h settings which were a warning and no longer
correct usage].
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
By reading 2 consecutive bytes from i2c to an u16 value
we have an endianess issue.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
|
|
Since busses are sorted in alphabetical order, introducing more
than nine busses led to unexpected behaviour.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
|
|
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
|
|
osdsize adjusts the gdsys IHS osd dimensions in characters.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
|
|
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
|
|
hrcon DH(dual head) has two video outputs per FPGA.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
|
|
- i2c addresses for the videoboard port expanders were
wrong.
- the fpga reset signal was not initialized.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
|
|
The strider platform moved some generic code into ioep-fpga.c.
Make use of that on hrcon platform.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
|
|
The gdsys strider board is based on a Freescale MPC8308 SOC.
It boots from NOR-Flash, kernel and rootfs are stored on
SD-Card.
On board peripherals include:
- 1x 10/100 Mbit/s Ethernet (optional)
- Lattice ECP3 FPGA connected via eLBC
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
[trini: Drop setting CONFIG_SYS_GENERIC_BOARD, this is always true now]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
hrcon has no CH7301 DVI-transmitter.
Probably not removed when copying from iocon.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
|
|
- Reset FPGAs in last_stage_init()
Signed-off-by: Reinhard Pfau <pfau@gdsys.de>
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
|
|
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
|
|
Support dlvision-10g hardware with displayport output.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
|
|
DP501 only supports DP 1.1a.
Limit settings for link bandwidth and lane count to
values allowed by DP 1.1a.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
|
|
With Club 3D dual link adapter there are AUX-channel timeouts
when EDID is read. Increasing retry interval time to max (400us)
fixes this.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
Bus has to be held for repeated start regardless of
read/write access.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
Reinhard Pfau complained that macros in ihs_i2c do not follow best practices.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
Support two i2c masters per FPGA.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
Fix below warnings happening for xilinx_zynqmp_ep_defconfig
drivers/net/zynq_gem.c: In function ‘zynq_gem_init’:
drivers/net/zynq_gem.c:330:7: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
((u32)(priv->rxbuffers) +
^
In file included from drivers/net/zynq_gem.c:19:0:
drivers/net/zynq_gem.c:336:10: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
writel((u32)priv->rx_bd, ®s->rxqbase);
^
./arch/arm/include/asm/io.h:146:34: note: in definition of macro ‘writel’
#define writel(v,c) ({ u32 __v = v; __iowmb(); __arch_putl(__v,c); __v; })
^
drivers/net/zynq_gem.c: In function ‘zynq_gem_send’:
drivers/net/zynq_gem.c:399:9: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
writel((u32)priv->tx_bd, ®s->txqbase);
^
./arch/arm/include/asm/io.h:146:34: note: in definition of macro ‘writel’
#define writel(v,c) ({ u32 __v = v; __iowmb(); __arch_putl(__v,c); __v; })
^
drivers/net/zynq_gem.c:404:22: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
priv->tx_bd->addr = (u32)ptr;
^
drivers/net/zynq_gem.c:409:9: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
addr = (u32) ptr;
^
drivers/net/zynq_gem.c:414:9: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
addr = (u32)priv->rxbuffers;
^
drivers/net/zynq_gem.c: In function ‘zynq_gem_recv’:
drivers/net/zynq_gem.c:454:31: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
net_process_received_packet((u8 *)addr, frame_len);
^
drivers/net/zynq_gem.c: In function ‘zynq_gem_initialize’:
drivers/net/zynq_gem.c:533:35: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
priv->rx_bd = (struct emac_bd *)((u32)bd_space + BD_SEPRN_SPACE);
^
drivers/net/zynq_gem.c:533:16: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
priv->rx_bd = (struct emac_bd *)((u32)bd_space + BD_SEPRN_SPACE);
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
|
|
Fix below compilation warings happening for hikey_defconfig
drivers/usb/eth/smsc95xx.c:698:56: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
debug("** %s(), len %d, buf %#x\n", __func__, length, (int)msg);
^
include/common.h:109:26: note: in definition of macro ‘debug_cond’
printf(pr_fmt(fmt), ##args); \
^
drivers/usb/eth/smsc95xx.c:698:2: note: in expansion of macro ‘debug’
debug("** %s(), len %d, buf %#x\n", __func__, length, (int)msg);
^
drivers/usb/eth/smsc95xx.c:718:2: warning: format ‘%u’ expects argument of
type ‘unsigned int’, but argument 2 has type ‘long unsigned int’ [-Wformat=]
debug("Tx: len = %u, actual = %u, err = %d\n",
^
drivers/usb/eth/smsc95xx.c: In function ‘smsc95xx_recv’:
drivers/usb/eth/smsc95xx.c:802:19: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
cur_buf_align = (int)buf_ptr - (int)recv_buf;
^
drivers/usb/eth/smsc95xx.c:802:34: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
cur_buf_align = (int)buf_ptr - (int)recv_buf;
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
|
|
Fix below compilation warings happening for hikey_defconfig
drivers/mmc/dw_mmc.c: In function ‘dwmci_set_idma_desc’:
drivers/mmc/dw_mmc.c:43:20: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
desc->next_addr = (unsigned int)desc + sizeof(struct dwmci_idmac);
^
drivers/mmc/dw_mmc.c: In function ‘dwmci_prepare_data’:
drivers/mmc/dw_mmc.c:61:35: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
dwmci_writel(host, DWMCI_DBADDR, (unsigned int)cur_idmac);
^
drivers/mmc/dw_mmc.c:73:9: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
(u32)bounce_buffer + (i * PAGE_SIZE));
^
CC drivers/mmc/hi6220_dw_mmc.o
drivers/mmc/hi6220_dw_mmc.c: In function ‘hi6220_dwmci_add_port’:
drivers/mmc/hi6220_dw_mmc.c:51:17: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
host->ioaddr = (void *)regbase;
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
|
|
Fix below compilation warnings-
drivers/gpio/hi6220_gpio.c: In function ‘hi6220_gpio_probe’:
drivers/gpio/hi6220_gpio.c:82:15: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
bank->base = (u8 *)plat->base;
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
|
|
This fixes compilation problems when using a hardfloat toolchain on
ARM, which manifest themselves as "libgcc.a(_udivmoddi4.o) uses
VFP register arguments, u-boot does not".
These problems have been reported in the U-Boot mailing list:
http://lists.denx.de/pipermail/u-boot/2015-October/230314.html
http://lists.denx.de/pipermail/u-boot/2015-October/231908.html
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
short strings can be used in type parameter of gpt command
to replace the guid string for the types known by u-boot
partitions = name=boot,size=0x6bc00,type=data; \
name=root,size=0x7538ba00,type=linux;
gpt write mmc 0 $partitions
and they are also used to display the type of partition
in "part list" command
Partition Map for MMC device 0 -- Partition Type: EFI
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00000022 0x0000037f "boot"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
type: data
guid: d117f98e-6f2c-d04b-a5b2-331a19f91cb2
2 0x00000380 0x003a9fdc "root"
attrs: 0x0000000000000000
type: 0fc63daf-8483-4772-8e79-3d69d8477de4
type: linux
guid: 25718777-d0ad-7443-9e60-02cb591c9737
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
|
