| Age | Commit message (Collapse) | Author |
|---|
|
The MPC8536DS_NAND SPL build was failing due to code size increase
introduced by commit:
commit 33f57bd553edf29dffef5a6c7d76e169c79a6049
Author: Kumar Gala <galak@kernel.crashing.org>
Date: Fri Mar 26 15:14:43 2010 -0500
85xx: Fix enabling of L1 cache parity on secondary cores
We built in some NS16550 functions that we dont need and can get
rid of them via CONFIG_NS16550_MIN_FUNCTIONS.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The Freescale P2020DS board uses a new type of PIXIS FPGA, called the ngPIXIS.
The ngPIXIS has one distinct new feature: the values of the on-board switches
can be selectively overridden with shadow registers. This feature is used to
boot from a different NOR flash bank, instead of having a register dedicated
for this purpose. Because the ngPIXIS is so different from the previous PIXIS,
a new file is introduced: ngpixis.c.
Also update the P2020DS checkboard() function to use the new macros defined
in the header file.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Refactor and document the Freescale PIXIS code, used on most 85xx and 86xx
boards. This makes the code easier to read and more flexible.
Delete pixis.h, because none of the exported functions were actually being
used by any other file. Make all of the functions in pixis.c 'static'.
Remove "#include pixis.h" from every file that has it.
Remove some unnecessary #includes.
Make 'pixis_base' into a macro, so that we don't need to define it in every
function.
Add "while(1);" loops at the end of functions that reset the board, so that
execution doesn't continue while the reset is in progress.
Replace in_8/out_8 calls with clrbits_8, setbits_8, or clrsetbits_8, where
appropriate.
Replace ulong/uint with their spelled-out equivalents. Remove unnecessary
typecasts, changing the types of some variables if necessary.
Add CONFIG_SYS_PIXIS_VCFGEN0_ENABLE and CONFIG_SYS_PIXIS_VBOOT_ENABLE to make
it easier for specific boards to support variations in the PIXIS registers
sets. No current boards appears to need this feature.
Fix the definition of CONFIG_SYS_PIXIS_VBOOT_MASK for the MPC8610 HPCD.
Apparently, "pixis_reset altbank" has never worked on this board.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The HID1[MBDD] bit is new on rev5.0 or greater cores and will optimize
the performance of mbar/eieio instructions.
Signed-off-by: Sandeep Gopalpet <sandeep.kumar@freescale.com>
|
|
There are various locations that we have chip specific info:
* Makefile for which ddr code to build
* Added P1012/P1013/P1021/P1022 to cpu_type_list and SVR list
* Added number of LAWs for P1012/P1013/P1021/P1022
* Set CONFIG_MAX_CPUS to 2 for P1021/P1022
* PCI port config
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
If the PCI controller wasn't configured or enabled delete from the
device tree (include its alias).
For the case that we didn't even configure u-boot with knowledge of
the controller we can use the fact that the pci_controller pointer
is NULL to delete the node in the device tree. We determine that
a controller was not setup (because of HW config) based on the fact
that cfg_addr wasn't setup.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add a helper function that given an alias will delete both the node
the alias points to and the alias itself
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
|
|
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
For 64B cacheline SoC, set the fixed 8-beat burst len,
for 32B cacheline SoC, set the On-The-Fly as default.
Signed-off-by: Dave Liu <daveliu@freescale.com>
|
|
Read-to-read/Write-to-write turnaround for same chip select
of DDR3 memory, BL/2+2 cycles is enough for them at BC4 and
OTF case, BL/2 cycles is enough for fixed BL8.
Cutting down the turnaround from BL/2+4 to BL/2+2 or BL/2
will improve the memory performance.
Signed-off-by: Dave Liu <daveliu@freescale.com>
|
|
When we set the read or write watermark in WML we should maintain the
rest of the register as is, rather than using some hard coded value.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
To support multiple block read command we must set abort or use auto
CMD12. If we booted from eSDHC controller neither of these are used
and thus we need to reset the controller to allow multiple block read
to function.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
We need to stop the clocks on 83xx/85xx as well as imx. No need to make
this code conditional to just imx.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
As this seems unclear, document how the flow of setting up
the MAC address is correct.
Signed-off-by: Heiko Schocher <hs@denx.de>
Text changed slightly, adding input from Mike Frysinger.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Only fill the device enetaddr with the contents of the eeprom,
do not program it in MAC address registers
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
|
|
The ramdisk sections in doc/uImage.FIT/multi.its lack
load address and entry point properties. Using examples
from this file will result in unbootable image, u-boot
will issue the following error messages:
Can't get ramdisk subimage load address!
Ramdisk image is corrupt or invalid
This patch adds missing properties to ramdisk sections.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
|
|
$ ./MAKEALL suen3
jffs2_1pass.c: In function 'get_fl_mem':
jffs2_1pass.c:399: warning: unused variable 'id'
jffs2_1pass.c: In function 'get_node_mem':
jffs2_1pass.c:423: warning: unused variable 'id'
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Tom <Tom.Rix@windriver.com>
|
|
|
|
|
|
After determining how much DDR is actually in the system, set DBAT0 and
IBAT0 accordingly. This ensures that the CPU won't attempt to access
(via speculation) addresses outside of actual memory.
On 86xx systems, DBAT0 and IBAT0 (the BATs for DDR) are initialized to 2GB
and kept that way. If the system has less than 2GB of memory (typical for
an MPC8610 HPCD), the CPU may attempt to access this memory during
speculation. The zlib code is notorious for generating such memory reads,
and indeed on the MPC8610, uncompressing the Linux kernel causes a machine
check (without this patch).
Currently we are limited to power of two sized DDR since we only use a
single bat. If a non-power of two size is used that is less than
CONFIG_MAX_MEM_MAPPED u-boot will crash.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Use the same code between primary and secondary cores to init the
L1 cache. We were not enabling cache parity on the secondary cores.
Also, reworked the L1 cache init code to match the e500mc L2 init code
that first invalidates the cache and locks. Than enables the cache and
makes sure its enabled before continuing.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This patch fixes a problem introduced with patch eb5eb2b0
[ppc4xx: Cleanup PPC4xx I2C infrastructure]. We need to assign the I2C
base address to the "i2c" pointer inside of the controller loop.
Otherwise controller 0 is initialized multiple times instead of
initializing each I2C controller sequentially.
Tested on Katmai.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
Booting a "Multi-File Image" including a linux kernel, ramdisk and
fdt, generated with
mkimage -A ppc \
-O linux \
-T multi \
-C gzip \
-a 00000000 \
-e 00000000 \
-n "kernel-2.6+initrd+dtb" \
-d "vmlinux.bin.gz:ramdisk_image.gz:board.dtb" \
multi.bin
actually fails, because ramdisk start and end addresses
didn;t get initialized. This patch fixes this issue.
Tested on the KUP4K board.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
and removed it from the .h file
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
|
|
The code to parse alen appeared 6 times in the function.
Factored this out in a small helper function
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
|
|
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
|
|
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
|
|
Declared all functions that were not called outside the file as static
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
|
|
|
|
|
|
Update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
The ml300 board has a number of issues, but nobody cares about this
long-orphaned board any more. Remove it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Michal Simek <monstr@monstr.eu>
|
|
|
|
The restructuring of the mkimage command in commit 89a4d6b1 ("tools:
mkimage: split code into core, default and FIT image specific")
introduced a bug that caused mkimage to segfault when run without
"-n name" option. Initialize the imagename entry to prevent that.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
|
|
|
|
This patch adds status polling method to offer an alternative to
data toggle method for amd flash chips.
This patch is needed for nios2 cfi flash interface, where the bus
controller performs 4 bytes read cycles for a single byte read
instruction. The data toggle method can not detect chip busy
status correctly. So we have to poll DQ7, which will be inverted
when the chip is busy.
This feature is enabled with the config def,
CONFIG_SYS_CFI_FLASH_STATUS_POLL
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
With old configuration it could happen tout=0 if CONFIG_SYS_HZ<1000.
Signed-off-by: Renato Andreola <renato.andreola@imagos.it>
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
The ATMEL flash does not have buffer write feature. Assgined
buffer_size = 1, so that when there is a write to the flash
will not use buffer write function.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
|
|
The flash location is at 0xff800000, not 0
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
|
|
The CF will call cache functions in lib_m68/cache.c and the
cache settings are defined in platform configuration file.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
|
|
The proper SDRAM size is 32MB not 64MB
Signed-off-by: Jingchang Lu <b22599@freescale.com>
|
|
Reside Ethernet buffer descriptors in SRAM instead of DRAM. Add
CONFIG_SYS_TX_ETH_BUFFER in platform configuration file. Update
DRAM control and SRAM control register setting. Update cache
setting where size does not write to proper region.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
|
|
Add CPU compile flag -mcpu=53015 in cpu/config.mk
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
|
|
Provide extra environment Data. Remove default network
address and MAC address.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
|
|
Fix proper portsize: The register for portsize is either 00b, 01b,
or 1xb. The value that previous assigned is 32d.
Fix DRAM bring up: insert asm("nop") for every DRAM register setup
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
|
|
Fix incorrect default environment for flash erase or protect
range. Change offset from 0 to 0xff80nnnn. Remove default
ethernet setup and MAC address.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
|
