| Age | Commit message (Collapse) | Author |
|---|
|
The error checking should also catch the case that no range has beeen
defined.
syscon_get_first_range() returns NULL if no range is defined.
cf. rk3399_mipi.c
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Pointers are never negative. Use macro IS_ERR() for checking.
cf. rk3288_mipi.c
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Assigning f_rkusb->reboot_flag twice doesn't make sense.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
If we want to check the duration we need to increment the counter.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Clean the iomux definitions at grf_rk3188.h, and move them into
pinctrl-driver for resolving the compiling error of redefinition.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Clean the iomux definitions at grf_rk3036.h, and move them into
pinctrl-driver for resolving the compiling error of redefinition.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
This adds support for the (to date unsupported) I2C controllers 1~4
and 6~7 (i.e. now all controllers except I2C5, which is not accessible
on the RK3399-Q7, are supported by pinctrl).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
The shift values for GPIO2B1 and GPIO2B2 had in fact referred to
GPIO2B0 and GPIO2B1, respectively. This substitutes the correct
values.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
|
|
|
|
|
|
Xilinx changes for v2018.05
- Fix mkimage recognition
- Update all my fragments
ZynqMP:
- Use clk driver
- Support loading elfs in el1
- Various DTS and defconfig changes
- Enable newer pmufw versions
- Support more clocks
- Remove ep108
- Secure image support
- Fix memtest setup
Zynq:
- Enabling watchdog driver
- Support more clocks
- defconfig changes
fpga:
- Simplify error path
net:
- GMII case update
|
|
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
|
|
Introduce another difference from upstream (kernel) source in
fs/ubifs/super.c: adding preprocessor condition as y variable in
mount_ubifs() depends on CONFIG_UBIFS_SILENCE_MSG:
fs/ubifs/super.c:1337:15: error: variable ?y? set but not used [-Werror=unused-but-set-variable]
long long x, y;
Not setting CONFIG_UBIFS_SILENCE_MSG in am335x_igep003x_defconfig and
igep0032_defconfig. Although it was defined in their config headers, it
depends on CMD_UBIFS which is not set for them.
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Heiko Schocher <hs@denx.de>
|
|
Use of CONFIG_UBIFS_SILENCE_MSG was added in
147162dac6 ("ubi: ubifs: Turn off verbose prints")
Then it was removed in
ff94bc40af ("mtd, ubi, ubifs: resync with Linux-3.14")
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
|
|
The ti,pindir-d0-out-d1-in property is not expected to have a value
according to the device-tree binding, so treat it as a boolean not a
uint property.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
Alexey:
1. Significantly rework cache-related functionality.
In particular that fixes coherency problems in some corner-cases,
allows us to enable and disable caches in run-time and still
have properly running system, finally support execution from
real flash (before we used to run from DDR from the very beginning).
2. Remove string routines implemented in assembly.
That allows us to build and run U-Boot on wide range of ARC cores
with different configurations. I.e. whatever tuning is used on GCC's
command-line we'll get code for desired flavor of ARC.
Otherwise for each and every corner-case we would need to add ifdefs
in assembly code to accommodate missing instructions etc.
3. Get use of GCC's garbage collector which helps to slim-down resulting image
quite a bit.
4. Also now we may disable U-Boot self-relocation for ARC if needed either
by platform or for debugging purposes.
|
|
Refactor GO and PREP subcommands implementation for a simpler
override in the boards platform code.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
Fix my fragments to list all files in the repo.
Also fix path to for Xilinx Zynq SoC (mach-zynq)
It should be the part of
"ARM: zynq: move SoC sources to mach-zynq"
(sha1: 0107f2403669f764ab726d0d404e35bb9447bbcc)
And cover dts files in board MAINTAINERS files.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
There is an issue to recognize zynq or zynqmp image because header
checking is just the same. That's why zynqmp images are recognized as
zynq one.
Check unused fields which are initialized to zero in zynq format
(__reserved1 0x38 and __reserved2 0x44) which are initialized for
zynqmp. This should ensure that images are properly recognized by:
./tools/mkimage -l spl/boot.bin
Also show image type as ZynqMP instead of Zynq which is confusing.
Reported-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Alexander Graf <agraf@suse.de>
|
|
This patch adds new command "zynqmp" to handle zynqmp
specific commands like "zynqmp secure". This secure command is
used for verifying zynqmp specific secure images. The secure
image can either be authenticated or encrypted or both encrypted
and authenticated. The secure image is prepared using bootgen
and will be in xilinx specific BOOT.BIN format. The optional
key can be used for decryption of encrypted image if user
key was specified while creation BOOT.BIN.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
ZynqMP Emulation board is no longer tested and there is no reason to
keep maintaining it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
The vcu disable bit in efuse ipdisable register is valid only
if PL powered up so, consider PL powerup status for determing
EG/EV part. If PL is not powered up, ignore EG/EV part of string.
The PL powerup status will be filled by pmufw based on PL PROGB
status in the 9th bit of version field.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch print pl clocks (pl0...pl3) and watchdog
clock using clk dump.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
NAND erase was not happening for size 1GiB or more. Erase
command was executing successfully but in actual, it was not
erasing.
This patch fixed erase issue for 1 GiB or more size nand.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Use appended dtb which is default option for zynq boards.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
The same command should be used for x16 configuration.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch changed CONFIG_SYS_MEMTEST_SCRATCH address to the
accessible DDR address used by alternate memory test.
Before this, 0xfffc0000 address was used, which is the OCM
address and not enabled in MMU table. So, whenever trying
to access 0xfffc0000 address, got Synchronous Abort exception.
After changing CONFIG_SYS_MEMTEST_SCRATCH address, alternate
memory test is working fine.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Enable watchdog with reset-on-timeout feature.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Watchdog is only enabled in full u-boot. Adoption for SPL should be also
done because that's the right place where watchdog should be enabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This IP can be found on Zynq and ZynqMP devices.
The driver was tested with reset-on-timeout; feature.
Also adding WATCHDOG symbol to Kconfig because it is required.
Signed-off-by: Shreenidhi Shedi <imshedi@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
watchdog clock is also connected to cpu 1X clocksource.
Zynq> clk dump
...
Before:
swdt 4294967290
After:
swdt 111111110
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
As of now newer pmufw is keeping old interfaces. That's why permit
u-boot to run on newer version. Recommended version will be setup later.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch bypasses phy detection logic for GMII interface
and just depend on phy address received from DT. This patch
is required as phy detection logic is different for some phys
like xilinx phy which can be connected over SGMII and GMII
interface.
This fixes the issue of ethernet failures when xilinx phy is
connected over GMII interface.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
This patch is adding support to switch to EL1 while loading an EL1
application with u-boot running at EL above EL1 in aarch64 mode.
Signed-off-by: Nitin Jain <nitinj@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
It helps with debugging.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Enable missing driver on this board.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Check !desc earlier to simplify code.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Reviewed-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
|
|
Make defconfigs up2date with current location.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Use zynqmp clock driver instead of fixed clocks.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
In
lpi2c_status_t result = A;
result = B;
the first assignment has no effect. Let's remove it.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
|
|
Enable Driver Model and Device-tree support for omapl138 board
in U-Boot. Also enable DM_SERIAL and DM_I2C.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Sync dts from Linux 4.16 and also add u-boot specific
dtsi for OMAPl138 board.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Commit 6aa4ad8e3820 ("Convert CONFIG_SOC_DA8XX et al to Kconfig")
converted SOC_DA8XX to Kconfig but missed enabling DDR_INIT for
SOC_DA8XX, which broke OMAPL138 to boot.
Commit 2e87980580d0 ("davinci: Fix omapl138_lcdk builds") disabled
DDR_INIT for all DA850 SoCs. This failed all DA850 boards to boot
as ddr is not being initialized.
Enable SYS_DA850_DDR_INIT for DA8XX so that all DA850 and OMAPL138
will have ddr initialized
Fixes: 2e87980580d0 ("davinci: Fix omapl138_lcdk builds")
Fixes: 6aa4ad8e3820 ("Convert CONFIG_SOC_DA8XX et al to Kconfig")
Reported-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: David Lechner <david@lechnology.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
With gpio devices getting created in SPL, the size of the heap is
no longer sufficient. Therefore, increase SPL_SYS_MALLOC_F_LEN
to 0x1000.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
With DM enabled in SPL, DM_FLAG_PRE_RELOC is required for
the omap_gpio driver to be bound to the gpio devices.
Therefore, add DM_FLAG_PRE_RELOC flag to the omap_gpio driver.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
scripts/check-config.sh exits successfully and silently without doing
any checks when the 'comm' command is not found.
The problem triggers from the command around line 39:
comm -23 ${suspects} ${ok} >${new_adhoc}
This statement fails when 'comm' is not in $PATH, creating an empty
${new_adhoc} file. But the script continues and the following line,
which is supposed to detect an error:
if [ -s ${new_adhoc} ]; then
will always be false since the file is empty, and the script will exit
successfully as if everything were OK.
The case where 'comm' in not in $PATH is not theoretical. It used to
happen on yocto until a recent fix [0], and still happens on the
current stable branch (rocko).
Fix by setting the errexit flag to exit with error when a statement
fails, so that at least the problem is noticed.
For additional safety also set the nounset flag to detect expansion
errors.
[0] http://git.yoctoproject.org/cgit/cgit.cgi/poky/commit/?id=fe0b4cb5b48580d4a3f3c0eb82bfa6f1b13801e4
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
commit 1601dd97edc6 ("davinci: omapl138_lcdk: increase PLL0 frequency")
changed the PLL0 frequency to 456MHz, which is needed for the LCDC IP
block. However, in doing so, it caused the PLLOUT clock to be outside
of the allowable specifications given in the OMAP-L138 data sheet. (It
says PLLOUT must be 600MHz max). It also uses a PLLM value outside of
the range given in the TRM (it says PLLM must in the range 0 to 0x1f).
So here is what we have currently:
PLLOUT = 24 / (0 + 1) * (37 + 1) = 912MHz (out of spec)
^ ^ ^
CLKIN PREDIV PLLM (out of spec)
input to PLLDIVn = 912 / (1 + 1) = 456MHz (desired result)
^ ^
PLLOUT POSTDIV
This changes the PLLM value to 18 and the POSTDIV value to 0 so that
PLLOUT is now within specification but we still get the desired
result.
PLLOUT = 24 / (0 + 1) * (18 + 1) = 456MHz (within spec)
^ ^ ^
CLKIN PREDIV PLLM
input to PLLDIVn = 456 / (0 + 1) = 456MHz (desired result)
^ ^
PLLOUT POSTDIV
Fixes: 1601dd97edc6 ("davinci: omapl138_lcdk: increase PLL0 frequency")
Signed-off-by: David Lechner <david@lechnology.com>
Reported-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
|
