summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-11-19ehci-mxc: Fix host power mask bit for i.MX25Benoît Thébaudeau
The correct bit for H1_PM is 16, not 8, which is the DP pull-up impedance selection bit. This issue has been reported by Eric Bénard <eric@eukrea.com> and fixed by Christoph Fritz <chf.fritz@googlemail.com> on Linux, from which these #define-s had been copied. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Marek Vasut <marex@denx.de>
2012-11-19mx35pdk: Configure CONFIG_BOOTDELAY to one secondFabio Estevam
One second is enough time for users to react in case they want to stop the booting process. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-11-19mx31pdk: Configure CONFIG_BOOTDELAY to one secondFabio Estevam
One second is enough time for users to react in case they want to stop the booting process. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-11-19mx25pdk: Configure CONFIG_BOOTDELAY to one secondFabio Estevam
One second is enough time for users to react in case they want to stop the booting process. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-11-19mx51evk: Configure CONFIG_BOOTDELAY to one secondFabio Estevam
One second is enough time for users to react in case they want to stop the booting process. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-11-19mx6qsabre_common: Configure CONFIG_BOOTDELAY to one secondFabio Estevam
One second is enough time for users to react in case they want to stop the booting process. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Jason Liu <r64343@freescale.com>
2012-11-19mx6qsabrelite: Configure CONFIG_BOOTDELAY to one secondFabio Estevam
One second is enough time for users to react in case they want to stop the booting process. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Jason Liu <r64343@freescale.com>
2012-11-19mx53loco: Configure CONFIG_BOOTDELAY to one secondFabio Estevam
One second is enough time for users to react in case they want to stop the booting process. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-11-19mx28evk: Configure CONFIG_BOOTDELAY to one secondFabio Estevam
One second is enough time for users to react in case they want to stop the booting process. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-11-19ehci-mxc: Fix host power mask bit for i.MX35Benoît Thébaudeau
The correct bit for H1_PM is 16, not 8, which is the DP pull-up impedance selection bit. This issue has been reported by Michael Burkey <mdburkey@gmail.com> and fixed by Christoph Fritz <chf.fritz@googlemail.com> on Linux, from which these #define-s had been copied. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Marek Vasut <marex@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
2012-11-19mx6: clock: Only show CSPI clock if CSPI is enabledFabio Estevam
If a board does not enable CSPI, there is no need to show the CSPI clock frequency as part of the 'clock' command. Reported-by: Dirk Behme <dirk.behme@gmail.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Dirk Behme <dirk.behme@gmail.com>
2012-11-19spi: mxc_spi: Fix spi clock glitch durant resetFabio Estevam
Measuring the spi clock line on a scope shows a 'glitch' during the reset of the spi. Fix this by toggling only the MXC_CSPICTRL_EN bit, so that the clock line becomes always stable. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2012-11-19spi: mxc_spi: Fix handling of chip selectFabio Estevam
In decode_cs() function the polarity of the chip select must be taken into account. Also, for the case of low active chip select, the CS was activated too early. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-11-19mx5: Print CSPI clock in 'clock' commandFabio Estevam
Print CSPI clock in 'clock' command. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2012-11-19mx5: Align SPI CS naming with i.MX53 reference manualFabio Estevam
Align SPI chip select naming with i.MX53 reference manual. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-11-16ehci-mx5/6: Make board_ehci_hcd_init() optionalBenoît Thébaudeau
A custom board_ehci_hcd_init() may be unneeded, so add a weak default implementation doing nothing. By the way, use simple __weak from linux/compiler.h for board_ehci_hcd_postinit() instead of weak alias with full attribute. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2012-11-16mx35pdk: Add support for OTGBenoît Thébaudeau
Add support for the OTG port on the mx35pdk Personality board. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Tested-by: Stefano Babic <sbabic@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Marek Vasut <marex@denx.de>
2012-11-16ehci-mxc: Add support for i.MX35Benoît Thébaudeau
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2012-11-16ehci-mxc: Define host offsetsBenoît Thébaudeau
Some MXC SoCs like the i.MX35 have hosts located at unusual offsets, so prepare to the introduction of i.MX35 support by defining the ehci-mxc hosts offsets at SoC level. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2012-11-16ehci-mxc: Make i.MX25 EHCI configurableBenoît Thébaudeau
Use EHCI MXC configuration options for i.MX25. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Matthias Weisser <weisserm@arcor.de>
2012-11-16ehci-mxc: Make EHCI power/oc polarities configurableBenoît Thébaudeau
Make EHCI power and overcurrent polarities configurable. If not set, these new configurartions keep the default register values so that existing board files do not have to be changed. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2012-11-16ehci-mx5: Add missing OC_DIS for i.MX53Benoît Thébaudeau
The i.MX53 has MXC_H*_UCTRL_H*_OC_DIS_BIT bits to disable the oc pin. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2012-11-16ehci-mx5: Fix *PM usage for i.MX53Benoît Thébaudeau
The MXC_*_UCTRL_*PM_BIT bits are available only on i.MX51. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2012-11-16ehci-mx5: Fix OPM usageBenoît Thébaudeau
MXC_OTG_UCTRL_OPM_BIT disables (masks) the power/oc pins if set, like MXC_H1_UCTRL_H1PM_BIT and MXC_H2_UCTRL_H2PM_BIT, not the opposite. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2012-11-16ehci-mx5: Fix OC_DIS usageBenoît Thébaudeau
MXC_OTG_PHYCTRL_OC_DIS_BIT disables the oc pin if set, like MXC_H1_OC_DIS_BIT, not the opposite. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2012-11-16ehci-mx5: Clean upBenoît Thébaudeau
Clean up ehci-mx5: - Fix column alignments. - Fix comments. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2012-11-16ehci-mxc: Clean upBenoît Thébaudeau
Clean up ehci-mxc: - Remove useless #if's. - Fix identation. - Issue a #error if used with an unsupported platform. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2012-11-16mx31: Move EHCI definitions to ehci-fsl.hBenoît Thébaudeau
The EHCI definitions in i.MX31's imx-regs.h are MXC-generic, so move them to ehci-fsl.h so that all MXC SoCs can use them. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2012-11-10arch-mx6: add mx6dl_pins.hTroy Kisky
Only the values used in the sabrelite board are added currently. Add more as other boards use them. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-11-10imx-common: cpu: add imx_ddr_sizeTroy Kisky
Read memory setup registers to determine size of available ram. This routine works for mx53/mx6x I need this because when mx6solo called get_ram_size with a too large maximum size, the system hanged. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-11-10mx6: use CONFIG_MX6 instead of CONFIG_MX6QTroy Kisky
Use CONFIG_MX6 when the particular processor variant isn't important. Reserve the use of CONFIG_MX6Q to specifically test for quad cores variant. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-11-10mx6: soc: update get_cpu_rev and get_imx_type for mx6solo/sololiteTroy Kisky
Previously, the same value was returned for both mx6dl and mx6solo. Check number of processors to differeniate. Also, a freescale patch says that sololite has its cpu/rev stored at 0x280 instead of 0x260. I don't have a sololite to verify. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-11-10Merge git://git.denx.de/u-bootStefano Babic
2012-11-09Merge branch 'master' of git://www.denx.de/git/u-boot-microblazeTom Rini
2012-11-08common/command.c: revert changes from commit 199adb60Anatolij Gustschin
commit 199adb601ff34bdbbd0667fac80dfe0a87bffc2b "common/misc: sparse fixes" broke the help command trying to fix the sparse error "command.c:44:38: error: bad constant expression". As Henrik points out, the fix was bad because the commit used CONFIG_SYS_MAXARGS whereas the code intended to use the maximum number of commands (not arguments to a command). Revert command.c changes to the original code as asked by Wolfgang. Reported-by: Henrik Nordström <henrik@henriknordstrom.net> Signed-off-by: Anatolij Gustschin <agust@denx.de>
2012-11-08microblaze: Fix compilation failure because of missing libdtsMichal Simek
Microblaze platform can use CONFIG_OF_EMBED option but also it is necessary to support boards which don't want to use this option. U-Boot doesn't compile dts/libdts.o for #undef CONFIG_OF_EMBED case that's why it should be guarded by ifdef. Signed-off-by: Michal Simek <monstr@monstr.eu>
2012-11-07microblaze: Remove asm/bitops.h from asm/posix_types.hMichal Simek
The patch "include/linux/byteorder: import latest endian definitions from linux" (sha1: eef1cf2d5cf1cae5fb76713e912263dedf110aeb) Introduced a lot of compilation failures with unknow types. include/linux/byteorder/big_endian.h:45:1: error: unknown type name '__le64' include/linux/byteorder/big_endian.h: In function '__cpu_to_le64p': include/linux/byteorder/big_endian.h:47:18: error: '__le64' undeclared (first use in this function) include/linux/byteorder/big_endian.h:47:18: note: each undeclared identifier is reported only once for each function it appears in include/linux/byteorder/big_endian.h:47:25: error: expected ';' before '__swab64p' include/linux/byteorder/big_endian.h: At top level: include/linux/byteorder/big_endian.h:49:1: error: unknown type name '__le64' include/linux/byteorder/big_endian.h:53:1: error: unknown type name '__le32' include/linux/byteorder/big_endian.h: In function '__cpu_to_le32p': include/linux/byteorder/big_endian.h:55:18: error: '__le32' undeclared (first use in this function) include/linux/byteorder/big_endian.h:55:25: error: expected ';' before '__swab32p' include/linux/byteorder/big_endian.h: At top level: include/linux/byteorder/big_endian.h:57:1: error: unknown type name '__le32' include/linux/byteorder/big_endian.h:61:1: error: unknown type name '__le16' ... Removing asm/bitops.h solved this problem. Signed-off-by: Michal Simek <monstr@monstr.eu>
2012-11-07microblaze: Flush caches before enabling themMichal Simek
Flushing caches is necessary because of soft reset which doesn't clear caches. Signed-off-by: Michal Simek <monstr@monstr.eu> Reviewed-by: Marek Vasut <marex@denx.de>
2012-11-07microblaze: Fix byteorder for microblazeMichal Simek
Just remove ancient code. Signed-off-by: Michal Simek <monstr@monstr.eu> Acked-by: Stephan Linz <linz@li-pro.net> Reviewed-by: Marek Vasut <marex@denx.de>
2012-11-07microblaze: Fix compilation warning in ext2_find_next_zero_bitMichal Simek
ext2_find_next_zero_bit must be also static if __swab32 is also static. Warning: include/asm/bitops.h:369:22: warning: '__fswab32' is static but used in inline function 'ext2_find_next_zero_bit' which is not static [enabled by default] Signed-off-by: Michal Simek <monstr@monstr.eu> Acked-by: Stephan Linz <linz@li-pro.net>
2012-11-05Merge branch 'master' of git://git.denx.de/u-boot-avr32Tom Rini
2012-11-05Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
2012-11-04Makefile: use EXTRAVERSION for -rc? tagWolfgang Denk
When using SUBLEVEL for the -rc? tag, this results in an ugly version string like "2013.01.-rc1" - let's use EXTRAVERSION instead to get the simple "2013.01-rc1" Signed-off-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
2012-11-04Prepare v2013.01-rc1Tom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2012-11-04patman: Add additional tags to ignoreSimon Glass
The BRANCH= tag can be used to indicate the destination branch for a commit. Ignore this tag. Also ignore the gerrit 'Commit-Ready:' tag. Signed-off-by: Simon Glass <sjg@chromium.org>
2012-11-04usb gadget ether: Fix warning in is_eth_addr_valid()Tom Rini
The gadget ethernet driver needs to keep copies of the MAC address (at both endpoints) as strings so it needs a custom function for validation of the MAC. It was not however performing a totally correct check and also was emitting a warning about a set but unused variable. The solution to both is that after checking the string contents we use the standard test for a valid MAC. Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Marek Vasut <marex@denx.de> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2012-11-04drivers/serial/serial_ns16550.c: sparse fixesKim Phillips
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-11-04drivers/mtd/nand: sparse fixesKim Phillips
nand_ecc.c:82:5: warning: symbol 'nand_calculate_ecc' was not declared. Should it be static? nand_ecc.c:155:5: warning: symbol 'nand_correct_data' was not declared. Should it be static? nand_base.c:2854:1: error: directive in argument list nand_base.c:2856:1: error: directive in argument list Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Acked-by: Scott Wood <scottwood@freescale.com>
2012-11-04drivers/mtd/cfi_flash.c: sparse fixesKim Phillips
cfi_flash.c:756:43: warning: Using plain integer as NULL pointer cfi_flash.c:1150:52: warning: cast to non-scalar cfi_flash.c:1433:46: warning: cast truncates bits from constant value (890089 becomes 89) cfi_flash.c:1490:61: warning: cast truncates bits from constant value (1f001f becomes 1f) cfi_flash.c:1508:61: warning: cast truncates bits from constant value (10001 becomes 1) cfi_flash.c:1738:63: warning: cast truncates bits from constant value (10001 becomes 1) cfi_flash.c:1857:6: warning: symbol '__flash_cmd_reset' was not declared. Should it be static? Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-11-04drivers/mmc/fsl_esdhc.c: sparse fixesKim Phillips
fsl_esdhc.c:71:6: warning: symbol 'esdhc_xfertyp' was not declared. Should it be static? fsl_esdhc.c:413:6: warning: symbol 'set_sysctl' was not declared. Should it be st Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
generated by cgit (git 2.34.1) at 2025-01-02 17:42:29 +0000