| Age | Commit message (Collapse) | Author |
|---|
|
Add missing parenthesis around the variable into the macro.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
Extend the boot device autodetection from SAMA5D2 only to the entire
SAMA5Dx family of microcontrollers.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[minor compile fix for SAMA5D2]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
|
|
This board is based on Snapper 9G45 which has an Atmel AT91SAM9G45 chip and
128MB of SDRAM. It includes a small LCD, 2xUSB host, SD card, Ethernet and
two UARTs.
Signed-off-by: Andre Renaud <andre@designa-electronics.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[apply CONFIG_BOOTDELAY transition]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
|
|
Add these definitions so that GPIOs can be used with driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-on: smartweb, corvus, taurus, axm
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
|
|
Add register definitions for the AT91 RTC so that this can potentially be
used in U-Boot.
Signed-off-by: Andre Renaud <andre@designa-electronics.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
|
|
Add this file from Linux v4.5.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-on: smartweb, corvus, taurus, axm
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
|
|
At present CONFIG_SKIP_LOWLEVEL_INIT prevents U-Boot from calling
lowlevel_init(). This means that the instruction cache is not enabled and
the board runs very slowly.
What is really needed in many cases is to skip the call to lowlevel_init()
but still perform CP15 init. Add an option to handle this.
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-on: smartweb, corvus, taurus, axm
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
|
|
This is available on AT91SAM9G45. Add the peripheral address and flag
definitions.
Signed-off-by: Andre Renaud <andre@designa-electronics.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
|
|
Currently omap_vcores which holds pmic data is being assigned based
on the SoC type. PMIC is not a part of SoC. It is logical to
to assign omap_vcores based on board type. Hence over ride the
vcores_init function and assign omap_vcores based on the board type.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
|
|
|
|
|
|
|
|
|
|
At present pinctrl driver gets probed in ich6_gpio driver's probe
routine, which has two issues:
- Pin's PADs only gets configured when GPIO driver is probed, which
is not done by default. This leaves the board in a partially
functional state as we must initialize PADs correctly to get
perepherals fully working.
- The probe routine of pinctrl driver is called multiple times, as
normally there are multiple GPIO controllers. It should really
be called just once.
Move the call to syscon_get_by_driver_data() from ich6_gpio driver
to cpu_init_r().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
|
|
As of today, the latest version FSP (gold4) for BayTrail misses the
PAD configuration of the SD controller's Card Detect signal. The
default PAD value for the CD pin sets the pin to work in GPIO mode,
which causes card detect status cannot be reflected by the Present
State register in the SD controller (bit 16 & bit 18 are always zero).
Add a configuration for this pin in the pinctrl node.
Note I've checked the PAD configuration for all the pins in all the
3 controllers (eMMC/SDIO/SD). Only this SDMMC3_CD_B pin does not get
initialized to correct mode by FSP. With fsp,emmc-boot-mode set to
2 (eMMC 4.1), eMMC pins are initialized to func 1, but if we set
fsp,emmc-boot-mode to 1 (auto), those pins are initialized to func 3
which is correct according to datasheet.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
At present all BayTrail boards configure fsp,emmc-boot-mode to 2,
which means "eMMC 4.1" per FSP documentation. However, eMMC 4.1
only shows up on some early stepping silicon of BayTrail SoC.
Newer stepping SoC integrates an eMMC 4.5 controller. Intel FSP
provides a config option fsp,emmc-boot-mode which tells FSP which
eMMC controller it initializes. Instead of hardcoded to 2, now
we change it to 1 which means "auto".
With this change, MinnowMax board (with a D0 stepping BayTrail SoC)
can see the eMMC 4.5 controller at PCI address 00.17.00 via U-Boot
'pci' command.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Without a 'reg' property, pinctrl driver probe routine fails in
its pre_probe() with a return value of -EINVAL.
Add 'reg' property for all BayTrail boards. Note for BayleyBay,
the pinctrl node is newly added.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
An accumulated length was incorrectly added to current each pass
through the loop. On system with more than 2 cores this caused a
corrupt MADT to be generated.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This patch adds QSPI boot support for LS2080AQDS board.
The QSPI boot image need to be programmed into the QSPI flash
first. Then we can switch to booting from QSPI memory space.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Add QSPI controller and slave dts node for LS2080AQDS board.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
QSPI module output SCLK divisor value is configured through SCFG.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Environment variable mcinitcmd is defined to initiate MC and DPL
deployment from the location where it is stored (NOR, NAND, SD, SATA,
USB) during booting. If this variable is not defined then macro
MC_BOOT_ENV_VAR will be null and MC will not be booted and DPL will
not be applied during U-boot booting.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
The SP805-WDT module on LS2080A requires configuration of PMU's
PCTBENR register to enable watchdog counter decrement and reset
signal generation. The watchdog clock needs to be enabled first.
Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Currently the AHB1 clock speed is configured as 200MHz by
the SPL, but this causes a subtle and hard to reproduce data
corruption in SRAM C (for example, this can't be easily
detected with a trivial memset/memcmp test).
For what it's worth, the Allwinner's BSP configures AHB1
as 200MHz, as can be verified by running the devmem2 tool
in the system running the Allwinner's kernel 3.10.x:
0x1C20028: PLL_PERIPH0_CTRL_REG = 0x90041811
0x1C20054: AHB1_APB1_CFG_REG = 0x3180
0x1C20058: APB2_CFG_REG = 0x1000000
0x1C2005C: AHB2_CFG_REG = 0x1
However the FEL mode uses more conservative settings (100MHz
for AHB1):
0x1C20028: PLL_PERIPH0_CTRL_REG = 0x90041811
0x1C20054: AHB1_APB1_CFG_REG = 0x3190
0x1C20058: APB2_CFG_REG = 0x1000000
0x1C2005C: AHB2_CFG_REG = 0x0
It is yet to be confirmed whether faster AHB1/AHB2 clock settings
can be used safely if we initialize the AXP803 PMIC instead of
using reset defaults. But in order to resolve the data corruption
problem right now, it's best to downclock AHB1 to a safe level.
Note that this issue only affects the SPL, which is not fully
supported on Allwinner A64 yet and it should not affect the boot0
usage (unless somebody can confirm SRAM C corruption with the
boot0 too).
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
For consistency with the other cache-related Kconfig entries & the
values actually set by boards, make CONFIG_SYS_DCACHE_LINE_SIZE an int
entry instead of a hex entry.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 372286217f05 ("MIPS: Split I & D cache line size config")
|
|
Commit fb64cda57998 ("MIPS: Abstract cache op loops with a macro")
accidentally modified invalidate_dcache_range to operate on the L1
Icache instead of the Dcache. Fix the cache op used to operate on the
Dcache.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: fb64cda57998 ("MIPS: Abstract cache op loops with a macro")
|
|
In the draco CPU board family, etamin is a new variant
with bigger flash and more RAM. Due to new flash that
uses larger pages (4K) some changes are necessary because
it impacts the MTD partition layout and the ubi mount
parameters.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
[trini: Move BOOTDELAY into defconfig, just always be 3 now]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
support in omap_nand_switch_ecc() also an eccstrength
from 16.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
U-Boot SPL 2016.03-rc3-00019-g6dfb4c2-dirty (Mar 09 2016 - 07:40:06)
SHC C3-Sample
MPU reference clock runs at 6 MHz
Setting MPU clock to 594 MHz
Enabling Spread Spectrum of 18 permille for MPU
Trying to boot from MMC
reading u-boot.img
reading u-boot.img
U-Boot 2016.03-rc3-00019-g6dfb4c2-dirty (Mar 09 2016 - 07:05:35 +0100)
Watchdog enabled
I2C: ready
DRAM: 512 MiB
reloc off 1f783000
MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
Net: cpsw
U-Boot#
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
make this function weak, so board code can setup in SPL
MMC init with board special values.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
Enable Spread Spectrum for the MPU by calculating the required
values and setting the registers accordingly.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
add missing CM_CLKMODE_DPLL_SSC_ACK_MASK,
CM_CLKMODE_DPLL_SSC_DOWNSPREAD_MASK and
CM_CLKMODE_DPLL_SSC_TYPE_MASK
defines. Used for enabling spread spectrum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
add missing:
OMAP_GPIO_IRQSTATUS_SET_0 and OMAP_GPIO_IRQSTATUS_SET_1
registers.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
I noticed secondary CPUs sometimes fail to wake up, and the root
cause is that the sev instruction wakes up slave CPUs before the
preceding the register write is observed by them.
The read-back of the accessed register does not guarantee the order.
In order to ensure the order between the register write and the sev
instruction, a dsb instruction should be executed prior to the sev.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This code auto-detects the best-match FDT file name, but it should
respect the user's choice if "fdt_file" environment is found in a
saved set of environments.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Because setenv() may fail, it is better to check its return code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This function is shared between PH1-LD11 and PH1-LD20. The difference
is the boot-mode latch for the USB boot mode.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The Boot ROM on PH1-LD11/LD20 exports built-in APIs to load images
from an eMMC device. They are useful to reduce the memory footprint
of SPL, rather than compiling the whole MMC framework.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Just sort the board entries, no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
This adds support for IS1 board. Pretty usual socfpga board,
256MB of RAM, does not have MMC, two SPI chips, one ethernet port, two
additional ethernet ports connected to the FPGA.
Signed-off-by: Pavel Machek <pavel@denx.de>
|
|
Both comments look like being copy & paste errors.
Signed-off-by: Michael Heimpold <michael.heimpold@i2se.com>
Cc: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
Conflicts:
configs/peach-pi_defconfig
configs/peach-pit_defconfig
|
|
Some SPL loaders (like Allwinner's boot0, and Broadcom's boot0)
require a header before the actual U-Boot binary to both check its
validity and to find other data to load. Sometimes this header may
only be a few bytes of information, and sometimes this might simply
be space that needs to be reserved for a post-processing tool.
Introduce a config option to allow assembler preprocessor commands
to be inserted into the code at the appropriate location; typical
assembler preprocessor commands might be:
.space 1000
.word 0x12345678
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
Commit Notes:
Please note that the current code:
start.S (arm64) and
vectors.S (arm)
already jumps over some portion of data already, so this option basically
just increases the size of this region (and the resulting binary).
For use with Allwinner's boot0 blob there is a tool called boot0img[1],
which fills the header to allow booting A64 based boards.
For the Pine64 we need a 1536 byte header (including the branch
instruction) at the moment, so we add this to the defconfig.
[1] https://github.com/apritzel/pine64/tree/master/tools
END
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Since bcopy() is no longer used, delete all remaining references to
it.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
|
|
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
|
|
To quit an EFI application we will need logic to jump to the caller
of a function without returning from the function we called into,
so we need setjmp/longjmp functionality.
This patch introduces a trivial implementation of these that I
verified works on armv7, thumb2 and aarch64.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Signed-off-by: Peter Howard <phoward@gme.net.au>
|
|
|
|
0xc000 is not sufficient page table size if dc4 with 4 gems
is enabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
