summaryrefslogtreecommitdiff
path: root/cpu
AgeCommit message (Collapse)Author
2007-05-09Add the files for the SMN42 boardPeter Pearse
2007-05-08add: reading special purpose registersMichal Simek
2007-05-08add: Microblaze V5 exception handlingMichal Simek
2007-05-08Merge git://www.denx.de/git/u-bootMichal Simek
Conflicts: include/asm-microblaze/microblaze_intc.h include/linux/stat.h
2007-05-07new: USE_MSR_INTR supportMichal Simek
2007-05-07[MPC5xxx] There are networking problems on the Motion-PRO board withBartlomiej Sieka
current PHY initalization code (tftp timeouts all the time). This commit temporarily disables PHY initalization sequence to make the networking operational, until a fix is found.
2007-05-07fix: interrupt handlerMichal Simek
remove asm code
2007-05-07fix: remove asm codeMichal Simek
2007-05-07fix: clean interruptMichal Simek
2007-05-07fix: interrupt handler for multiple sourcesMichal Simek
2007-05-055xxx: write MAC address to mac-address and local-mac-addressTimur Tabi
Some device trees have a mac-address property, some have local-mac-address, and some have both. To support all of these device trees, ftp_cpu_setup() should write the MAC address to mac-address and local-mac-address, if they exist. Signed-off-by: Timur Tabi <timur@freescale.com> Acked-by: Grant Likely <grant.likely@secretlab.ca>
2007-05-05[PATCH] Use PVR to distinguish MPC5200B from MPC5200 in boot messageGrzegorz Wianecki
MPC5200B systems are incorrectly reported as MPC5200 in U-Boot start-up message. Use PVR to distinguish between the two variants, and print proper CPU information. Signed-off-by: Grzegorz Wianecki <grzegorz.wianecki@gmail.com> Signed-off-by: Bartlomiej Sieka <tur@semihalf.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2007-05-05Coding stylke cleanup; update CHANGELOG.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2007-05-05Merge with /home/wd/git/u-boot/custodian/u-boot-ppc4xxWolfgang Denk
2007-05-05Merge with /home/wd/git/u-boot/custodian/u-boot-mpc85xxWolfgang Denk
2007-05-05Merge with /home/wd/git/u-boot/custodian/u-boot-nand-flashWolfgang Denk
2007-05-02Cleaned up some 85xx PCI bugsAndy Fleming
* Cleaned up the CDS PCI Config Tables and added NULL entries to the end * Fixed PCIe LAWBAR assignemt to use the cpu-relative address * Fixed 85xx PCI code to assign powar region sizes based on the config values (rather than hard-coding them) * Fixed the 8548 CDS PCI2 IO to once again have 0 as the base address Signed-off-by: Andy Fleming <afleming@freescale.com>
2007-05-02Add support for the 8568 MDS boardAndy Fleming
This included some changes to common files: * Add 8568 processor SVR to various places * Add support for setting the qe bus-frequency value in the dts * Add the 8568MDS target to the Makefile Signed-off-by: Andy Fleming <afleming@freescale.com>
2007-05-01Conditionalize 8641 Rev1.0 MCM workaroundsJames Yang
Signed-off-by: James Yang <James.Yang@freescale.com> Signed-off-by: Jon Loeliger <jdl@freescale.com>
2007-05-01Fix memory initialization on MPC8349E-mITXTimur Tabi
Define CFG_DDR_SDRAM_CLK_CNTL for the MPC8349E-mITX and MPC8349E-mITX-GP. This allows ddr->sdram_clk_cntl to be properly initialized. This is necessary on some ITX boards, notably those with a revision 3.1 CPU. Also change spd_sdram() in cpu/mpc83xx/spd_sdram.c to not write anything into ddr->sdram_clk_cntl if CFG_DDR_SDRAM_CLK_CNTL is not defined. Signed-off-by: Timur Tabi <timur@freescale.com> Acked-by: Michael Benedict <MBenedict@twacs.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2007-05-01mpc83xx: replace elaborate boottime verbosity with 'clocks' commandKim Phillips
and fix CPU: to align with Board: display text. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2007-05-01Rewrote picos_to_clk() to avoid rounding errors.James Yang
Clarified that conversion is to DRAM clocks rather than platform clocks. Made function static to spd_sdram.c. Signed-off-by: James Yang <James.Yang@freescale.com> Signed-off-by: Jon Loeliger <jdl@freescale.com>
2007-04-29Merge with git://www.denx.de/git/u-boot.gitStefan Roese
2007-04-25mpc83xx: minor fixups for 8313rdb introductionKim Phillips
2007-04-24ppc4xx: setup 440EPx/GRx ZMII/RGMII bridge depending on PFC register content.Matthias Fuchs
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2007-04-23Reworked 85xx speed detection codeAndy Fleming
Changed the code to read the registers and calculate the clock rates, rather than using a "switch" statement. Idea from Andrew Klossner <andrew@cesa.opbu.xerox.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2007-04-23Support 1G size on 8548Andy Fleming
e500v2 and newer cores support 1G page sizes. Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2007-04-23Only set ddrioovcr for 8548 rev1.Andy Fleming
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2007-04-23Tweak DDR ECC error counterAndy Fleming
Enable single-bit error counter when memory was cleared by ddr controller. Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2007-04-2385xx: write MAC address to mac-address and local-mac-addressTimur Tabi
Some device trees have a mac-address property, some have local-mac-address, and some have both. To support all of these device trees, ftp_cpu_setup() should write the MAC address to mac-address and local-mac-address, if they exist. Signed-off-by: Timur Tabi <timur@freescale.com>
2007-04-23Some 85xx cpu cleanupsAndy Fleming
* Cleaned up the TSR[WIS] clearing * Cleaned up DMA initialization Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: Jon Loeliger <jdl@freescale.com> Acked-by: Andy Fleming <afleming@freescale.com>
2007-04-23Add cpu support for the 8544Andy Fleming
Recognize new SVR values, and add a few register definitions Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: Jon Loeliger <jdl@freescale.com> Acked-by: Andy Fleming <afleming@freescale.com>
2007-04-23u-boot: Fix e500 v2 core reset bugZang Roy-r61911
The following patch fixes the e500 v2 core reset bug. For e500 v2 core, a new reset control register is added to reset the processor. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
2007-04-23u-boot: v2: Remove the fixed TLB and LAW entrynubmerZang Roy-r61911
Remove the fixed TLB and LAW entry nubmer. Use actually TLB and LAW entry number to control the loop. This can reduce the potential risk for the 85xx processor increasing its TLB adn LAW entry number. Signed-off-by: Swarthout Edward <swarthout@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
2007-04-23mpc83xx: Add generic PCI setup code.Scott Wood
Board code can now request the generic setup code rather than having to copy-and-paste it for themselves. Boards should be converted to use this once they're tested with it. Signed-off-by: Scott Wood <scottwood@freescale.com>
2007-04-23mpc83xx: Add 831x support to speed.c.Scott Wood
Signed-off-by: Scott Wood <scottwood@freescale.com>
2007-04-23mpc83xx: Change PVR_83xx to PVR_E300C1-3, and update checkcpu().Scott Wood
Rather than misleadingly define PVR_83xx as the specific type of 83xx being built for, the PVR of each core revision is defined. checkcpu() now prints the core that it detects, rather than aborting if it doesn't find what it thinks it wants. Signed-off-by: Scott Wood <scottwood@freescale.com>
2007-04-23mpc83xx: Recognize SPR values for MPC8311 and MPC8313.Scott Wood
Signed-off-by: Scott Wood <scottwood@freescale.com>
2007-04-23Merge git://www.denx.de/git/u-bootKim Phillips
2007-04-23Remove BOARDLIBS usage completelyStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-04-2116bit read/write little endianMichal Simek
2007-04-20mpc86xx; Write MAC address to mac-address and local-mac-addressJon Loeliger
Some device trees have a mac-address property, some have local-mac-address, and some have both. To support all of these device trees, ftp_cpu_setup() should write the MAC address to mac-address and local-mac-address, if they exist. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Jon Loeliger <jdl@freescale.com>
2007-04-20mpc86xx: protect memcpy to bad address if a mac-address is missing from dtJon Loeliger
Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Jon Loeliger <jdl@freescale.com>
2007-04-18Merge with /home/wd/git/u-boot/custodian/u-boot-fdtWolfgang Denk
2007-04-18Merge with /home/wd/git/u-boot/custodian/u-boot-mpc86xxWolfgang Denk
2007-04-18Merge with /home/wd/git/u-boot/custodian/u-boot-74xx-7xxWolfgang Denk
2007-04-18Merge with /home/wd/git/u-boot/custodian/u-boot-avr32; code cleanup.Wolfgang Denk
2007-04-18Merge with /home/wd/git/u-boot/custodian/u-boot-blackfinWolfgang Denk
2007-04-18Merge with git://www.denx.de/git/u-boot.gitStefan Roese
2007-04-18ppc4xx: Add output for bootrom location to 405EZ portsStefan Roese
Now 405EZ ports also show upon bootup from which boot device they are configured to boot: U-Boot 1.2.0-gd3832e8f-dirty (Apr 18 2007 - 07:47:05) CPU: AMCC PowerPC 405EZ Rev. A at 199.999 MHz (PLB=133, OPB=66, EBC=66 MHz) Bootstrap Option E - Boot ROM Location EBC (32 bits) 16 kB I-Cache 16 kB D-Cache Board: Acadia - AMCC PPC405EZ Evaluation Board Signed-off-by: Stefan Roese <sr@denx.de>
generated by cgit (git 2.34.1) at 2024-12-28 15:57:32 +0000