summaryrefslogtreecommitdiff
path: root/include
AgeCommit message (Collapse)Author
2018-01-19ARC: devboards: Allow huge uImages (up to 128 MiB)Alexey Brodkin
Even though in production uImage usually is quite small as it contains just Linux kernel image during development it might be pretty convenient to have root-FS built into the same image. That makes uImage much larger but given on our dev platforms we have quite a lot of DDR (> 512 MiB) we may afford loading huge uImages. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2018-01-19ARC: HSDK: CGU: Update AXI, TUN, ARC clock optionsEugeniy Paltsev
Update default AXI, TUN, ARC clock set options: instead of changing only IDIV divider settings adjust also domain PLL settings. Add support of TUN_ROM and TUN_PWM clocks (subclocks of TUNN_PLL) Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2018-01-17Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
2018-01-17armv8: ls1088ardb: Add environment variable address location for QSPI-NORAshish Kumar
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-17arm64: ls1012a: Add sata distro boot supportYuantian Tang
Sata is equipped on ls1012a and can be a boot source. Add sata boot support as an option if available. Signed-off-by: Tang Yuantian <andy.tang@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-17arm64: ls1046a: Add sata distro boot supportYuantian Tang
Sata is equipped on ls1046a and can be a boot source. Add sata boot support as an option if available. Signed-off-by: Tang Yuantian <andy.tang@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-16Merge git://git.denx.de/u-boot-dmTom Rini
2018-01-15fix incorrect usage of DT node unit address in commentsAndre Przywara
The DT spec demands a unit-address in a node name to match the "reg" property in that node. Newer dtc versions will throw warnings if this is not the case. Fix all occurences in the tree where node names were mentioned in comments, to not give bad examples to the reader. Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2018-01-15Merge git://git.denx.de/u-boot-netTom Rini
2018-01-15Merge git://git.denx.de/u-boot-imxTom Rini
2018-01-15db410c: on aarch64 the fdtfile is in per-vendor subdirectoryRob Clark
Signed-off-by: Rob Clark <robdclark@gmail.com>
2018-01-15fdtdec: allow board to provide fdt for CONFIG_OF_SEPARATERob Clark
Similar to CONFIG_OF_BOARD, but in this case the fdt is still built by u-boot build. This allows the board to patch the fdt, etc. In the specific case of dragonboard 410c, we pass the u-boot generated fdt to the previous stage of bootloader (by embedding it in the u-boot.img that is loaded by lk/aboot), which patches the fdt and passes it back to u-boot. Signed-off-by: Rob Clark <robdclark@gmail.com> [trini: Update board_fdt_blob_setup #if check] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-01-15db410c: configs: increase gunzip buffer size for the kernelJorge Ramirez-Ortiz
the kernel fails to boot when it goes over the limit. Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
2018-01-15db820c: stop autoboot when vol- pressedJorge Ramirez-Ortiz
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
2018-01-15db820c: add qualcomm dragonboard 820C supportJorge Ramirez-Ortiz
This commit adds support for 96Boards Dragonboard820C. The board is based on APQ8086 Qualcomm Soc, complying with the 96Boards specification. Features - 4x Kyro CPU (64 bit) up to 2.15GHz - USB2.0 - USB3.0 - ISP - Qualcomm Hexagon DSP - SD 3.0 (UHS-I) - UFS 2.0 - Qualcomm Adreno 530 GPU - GPS - BT 4.2 - Wi-Fi 2.4GHz, 5GHz (802.11ac) - PCIe 2.0 - MIPI-CSI, MIPI-DSI - I2S U-Boot boots chained from LK (LK implements the fastboot protocol) in 64-bit mode. For detailed build instructions see readme.txt in the board directory. Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
2018-01-15board: ls1012a: LS1012A-2G5RDB board supportBhaskar Upadhaya
LS1012A-2G5RDB belongs to LS1012A family with features 2 2.5G SGMII PFE MAC, SATA, USB 2.0/3.0, WiFi DDR, eMMC, QuadSPI, UART. Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-15net: sh-eth: Add to Kconfig and convertNobuhiro Iwamatsu
This adds SH_ETHER to drivers/net/Kconfig and convert to Kconfig. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-01-15net: phy: Add Broadcom BCM53xx switch driverFlorian Fainelli
Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar to the Marvell MV88E617x. This takes care of configuring the minimum amount out of the switch hardware such that each user visible port (configurable) and the CPU port can forward packets between each other while preserving isolation with other ports. This is useful for e.g: the Lamobo R1 board featuring a Broadcom BCM53125 switch. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2018-01-15poplar: configs: increase gunzip buffer size for the kernelJorge Ramirez-Ortiz
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
2018-01-14Merge git://git.denx.de/u-boot-mmcTom Rini
2018-01-12Merge git://git.denx.de/u-boot-tegraTom Rini
2018-01-12ARM: Tegra: p2771-0000: use calculate env var featureStephen Warren
Request that all environment variables containing hard-coded address be calculated at boot time instead. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2018-01-12ARM: tegra: p2771-000: increase max DRAM bank countStephen Warren
On this platform, there may be up to 1024 unusable chunks of memory. Increase CONFIG_NR_DRAM_BANKS so that U-Boot can remember all the banks required to represent such fragmented memory. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2018-01-12ARM: tegra: use CONFIG_SYS_INIT_SP_BSS_OFFSETStephen Warren
Enable CONFIG_SYS_INIT_SP_BSS_OFFSET for all 64-bit Tegra boards. Place the stack/... 512KiB from the end of the U-Boot binary. This should be plenty to accommodate the current DTBs (max 64 KiB), early malloc region (6KiB), stack usage, and plenty of slack, while still not placing it too far away from the U-Boot binary. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2018-01-12ARM: tegra: remove SPL config for non-SPL SoCsStephen Warren
No 64-bit Tegra uses SPL. Remove various unused definitions from config headers. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2018-01-12ARM: imx: cm_fx6: env: try to determine dtb to useChristopher Spinrath
Some distributions like Fedora expect U-Boot to select a proper devicetree. Since there are several variants of the cm-fx6 module featuring different SoC variants and the module can be paired with several baseboards, it is not viable to hardcode a filename. Instead, follow the lead of other i.MX6 based devices and try to determine the devicetree to use with the help of the board name and the SoC variant exported by the board code, before calling the distro bootcommand. For now, only for the Utilite Pro a proper devicetree filename is known but further variants of the Utilite Computer or other devices based on the cm-fx6 module may be added in the future. Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
2018-01-12ARM: imx: cm_fx6: export board and soc info to envChristopher Spinrath
Like many other i.MX6 based boards, there are multiple variants of the cm-fx6 module featuring different SoC variants. Furthermore, the module can be paired with multiple baseboards. At the same time modern distribution like Fedora require U-Boot to select a proper devicetree which depends on the SoC variant and the baseboard. Thus, export the SoC variant and the actual board to the environment following the conventions of other i.MX6 devices (e.g. the NXP boards) such that the environment can select a devicetree file to load. For now, we only know for sure that the cm-fx6 module and the SB-fx6m baseboard amount to a Utilite Computer variant (depending on the SoC). Further combinations may be added in the future; e.g. CompuLab's evaluation board once someone can verify the identification string stored in its eeprom. Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de> Reviewed-by: Stefano Babic <sbabic@denx.de>
2018-01-12imx: mx6ull-14x14-evk: enable DM QSPI driverPeng Fan
To support QSPI DM driver - Add spi0 alias for qspi node. Which is used for bus number 0. - Modify the n25q256a@0 compatible property to "spi-flash". - Modify spi4 (gpio_spi) node to spi5 - Define DM SPI/QSPI related config to enable QSPI Signed-off-by: Peng Fan <peng.fan@nxp.com>
2018-01-12imx: mx6sxsabresd: enlarge ENV offsetPeng Fan
The u-boot-dtb.imx size is about 519KB, so 8 * 64KB conflicts with u-boot-dtb.imx. Enlarge the offset to 14 * 64KB to fix it. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-12imx: mx6sxsabresd: Enable DM driverPeng Fan
Enable I2C/MMC/GPIO/REGUALTOR/PMIC/USB DM drivers. There are some dependency, such as when DM MMC enabled, USB compile error. Also the i.MX I2C MMC DM driver does not support legacy GPIO interface. So enable them all together. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-12mx6: Support SKS-Kinkel sksimx6 BoardStefano Babic
Board has 1GB RAM and boots from SD Card U-Boot SPL 2018.01-rc3-00005-ga1898b8 (Jan 02 2018 - 13:48:54) BT_FUSE_SEL already fused, will do nothing Trying to boot from MMC1 U-Boot 2018.01-rc3-00005-ga1898b8 (Jan 02 2018 - 13:48:54 +0100) CPU: Freescale i.MX6DL rev1.2 996 MHz (running at 792 MHz) CPU: Commercial temperature grade (0C to 95C) at 40C Reset cause: POR I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0 In: serial Out: serial Err: serial Net: FEC [PRIME] Signed-off-by: Stefano Babic <sbabic@denx.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-12riscv: Modify generic codes to support RISC-VRick Chen
Support common commands bdinfo and image format, also modify common generic flow for RISC-V. Signed-off-by: Rick Chen <rick@andestech.com> Signed-off-by: Rick Chen <rickchen36@gmail.com> Signed-off-by: Greentime Hu <green.hu@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-01-12riscv: configs: Add nx25-ae250.h to support RISC-VRick Chen
Add nx25-ae250 board configuartion options for RISC-V Signed-off-by: Rick Chen <rick@andestech.com> Signed-off-by: Rick Chen <rickchen36@gmail.com> Signed-off-by: Greentime Hu <green.hu@gmail.com>
2018-01-12mmc: remove hc_wp_grp_size from struct mmc if not neededJean-Jacques Hiblot
hc_wp_grp_size is needed only if hardware partitionning is used. On ARM removing it saves about 30 bytes of code space. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12mmc: don't read the size of eMMC enhanced user data area in SPLJean-Jacques Hiblot
This information is only used by the "mmc info" command. On ARM removing this information from SPL saves about 140 of code space. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12mmc: compile out erase and write mmc commands if write operations are not ↵Jean-Jacques Hiblot
enabled Also remove erase_grp_size and write_bl_len from struct mmc as they are not used anymore. On ARM, removing them saves about 100 bytes of code space in SPL. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12mmc: read ssr only if MMC write support is enabledJean-Jacques Hiblot
The content of ssr is useful only for erase operations. on ARM, removing sd_read_ssr() saves around 300 bytes. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12mmc: make UHS and HS200 optionalJean-Jacques Hiblot
Supporting USH and HS200 increases the code size as it brings in IO voltage control, tuning and fatter data structures. Use Kconfig configuration to select which of those features should be built in. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12dm: mmc: update mmc_of_parse()Jean-Jacques Hiblot
* convert to livetree API * don't fail because of an invalid bus-width, instead default to 1-bit. * recognize 1.2v DDR and 1.2v HS200 flags Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12dm: mmc: Add a library function to parse generic dt bindingKishon Vijay Abraham I
Add a new function to parse host controller dt node and set mmc_config. This function can be used by mmc controller drivers to set the generic mmc_config. This function can be extended to set other UHS mode caps once UHS mode support is added. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12mmc: add a library function to send tuning commandJean-Jacques Hiblot
HS200/SDR104 requires tuning command to be sent to the card. Add a simple function to send tuning command and to read and compare the received data with the tuning block pattern. This function can be used by platform driver to perform DLL tuning. This patch is similar to commit 996903de92f0 ("mmc: core: add core-level function for sending tuning commands") added in linux kernel. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12mmc: use the right voltage level for MMC DDR and HS200 modesJean-Jacques Hiblot
HS200 only supports 1.2v and 1.8v signal voltages. DDR52 supports 3.3v/1.8v or 1.2v signal voltages. Select the lowest voltage available when using those modes. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12mmc: Retry some MMC cmds on failureKishon Vijay Abraham I
With certain SD cards like Kingston 8GB/16GB UHS card, it is seen that MMC_CMD_ALL_SEND_CID cmd fails on first attempt, but succeeds subsequently. Therefore, retry MMC_CMD_ALL_SEND_CID cmd a few time as done in Linux kernel. Similarly, it is seen that MMC_CMD_SET_BLOCKLEN may fail on first attempt, therefore retry this cmd a few times as done in kernel. To make it clear that those are optionnal workarounds, a new Kconfig option 'MMC_QUIRKS' is added (enabled by default). Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12mmc: Change mode when switching to a boot partitionJean-Jacques Hiblot
Boot partitions do not support HS200. Changing to a lower performance mode is required to access them. mmc_select_mode_and_width() and sd_select_mode_and_width() are modified to make it easier to call them outside of the initialization context. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-01-12mmc: disable UHS modes if Vcc cannot be switched on and offJean-Jacques Hiblot
If a power cycle cannot be done on Vcc, it is safer not to try the UHS modes because we wouldn't be able to recover from an error occurring during the UHS initialization. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12mmc: Add support for UHS modesJean-Jacques Hiblot
Add UHS modes to the list of supported modes, get the UHS capabilites of the SDcard and implement the procedure to switch the voltage (UHS modes use 1v8 IO lines) During the voltage switch procedure, DAT0 is used by the card to signal when it's ready. The optional card_busy() callback can be used to get this information from the host driver. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-01-12mmc: add HS200 support in MMC coreKishon Vijay Abraham I
Add HS200 to the list of supported modes and introduce tuning in the MMC startup process. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-01-12mmc: Add a execute_tuning() callback to the mmc operations.Kishon Vijay Abraham I
Tuning is a mandatory step in the initialization of SDR104 and HS200 modes. This callback execute the tuning process. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12mmc: add a new mmc parameter to disable mmc clockKishon Vijay Abraham I
mmc clock has to be disabled in certain cases like during the voltage switch sequence. Modify mmc_set_clock function to take disable as an argument that signifies if the clock has to be enabled or disabled. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12mmc: Add a new callback function to perform the 74 clocks cycle sequenceJean-Jacques Hiblot
Add a new callback function *send_init_stream* which start a sequence of at least 74 clock cycles. The mmc core uses *mmc_send_init_stream* in order to invoke the callback function. This will be used during power cycle where the specification requires such a sequence after power up. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
generated by cgit (git 2.34.1) at 2024-12-26 07:43:34 +0000